ALTIGA-HARDWARE-STATS-MIB -- *------------------------------------------------------------------ -- * ALTIGA-HARDWARE-STATS-MIB.my: Altiga Hardware Statistics MIB. -- * -- * Altiga Networks was acquired by Cisco Systems on March 29, 2000 -- * -- * Copyright (c) 2002, 2003 by Cisco Systems, Inc. -- * All rights reserved. -- * -- *------------------------------------------------------------------ ALTIGA-HARDWARE-STATS-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Gauge32, Counter32, TimeTicks, Unsigned32 FROM SNMPv2-SMI DisplayString, TruthValue, TEXTUAL-CONVENTION FROM SNMPv2-TC OBJECT-GROUP, MODULE-COMPLIANCE FROM SNMPv2-CONF alStatsHardware, alHardwareGroup FROM ALTIGA-MIB alHardwareMibModule FROM ALTIGA-GLOBAL-REG; altigaHardwareStatsMibModule MODULE-IDENTITY LAST-UPDATED "200303271300Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-cvpn3000@cisco.com" DESCRIPTION "The Altiga Hardware Statistics MIB models counters and objects that are of management interest for the hardware. Acronyms The following acronyms are used in this document: CPU: Central Processing Unit MB: Megabyte MIB: Management Information Base PS: Power Supply RPM: Revolutions Per Minute SEP: Scalable Encryption Processor WAN: Wide Area Network " REVISION "200303271300Z" DESCRIPTION "Added new emun to ConcentratorCard." REVISION "200209051300Z" DESCRIPTION "Added module compliance." REVISION "200207100000Z" DESCRIPTION "Updated with new header" ::= { alHardwareMibModule 2 } -- +++++++++++++++++++++++++++++++++++++++++++++++++++++++ -- MIB Objects -- +++++++++++++++++++++++++++++++++++++++++++++++++++++++ ConcentratorCard ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Concentrator Card Type." SYNTAX INTEGER { none(1), sep(2), dualT1Wan(3), sepE(4) } ConcentratorType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Concentrator Type indicates the chassis type." SYNTAX INTEGER { cxx(1), -- VPN3015 through VPN3080 c5(2), -- VPN3005 c1(3) -- VPN3002 } alStatsHardwareGlobal OBJECT IDENTIFIER ::= { alStatsHardware 1 } -- Current Settings and Alarms alHardwareCpuVoltage OBJECT-TYPE SYNTAX Gauge32 UNITS "centivolts" MAX-ACCESS read-only STATUS current DESCRIPTION "The current CPU voltage in centivolts." ::= { alStatsHardwareGlobal 1 } alHardwareCpuVoltageAlarm OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The alarm status for CPU voltage. This alarm will fired when the CPU voltage is detected out of configured range." ::= { alStatsHardwareGlobal 2 } alHardwareCpuVoltageCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of alarm events for CPU voltage." ::= { alStatsHardwareGlobal 3 } alHardwareCpuVoltageTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The sysUptime at the time of the last change of alarm status for CPU voltage." ::= { alStatsHardwareGlobal 4 } alHardwarePs1Voltage3v OBJECT-TYPE SYNTAX Gauge32 UNITS "centivolts" MAX-ACCESS read-only STATUS current DESCRIPTION "The current 3V voltage of Power Supply 1 in centivolts." ::= { alStatsHardwareGlobal 5 } alHardwarePs1Voltage3vAlarm OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The alarm status for PS1 3v voltage. This alarm will fired when the 3v power supply 1 voltage is detected out of configured range." ::= { alStatsHardwareGlobal 6 } alHardwarePs1Voltage3vCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of alarm events for PS1 3v voltage." ::= { alStatsHardwareGlobal 7 } alHardwarePs1Voltage3vTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The sysUptime at the time of the last change of alarm status for PS1 3v voltage." ::= { alStatsHardwareGlobal 8 } alHardwarePs1Voltage5v OBJECT-TYPE SYNTAX Gauge32 UNITS "centivolts" MAX-ACCESS read-only STATUS current DESCRIPTION "The current 5V voltage of Power Supply 1 in centivolts." ::= { alStatsHardwareGlobal 9 } alHardwarePs1Voltage5vAlarm OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The alarm status for PS1 5v voltage. This alarm will fired when the 5v power supply 1 voltage is detected out of configured range." ::= { alStatsHardwareGlobal 10 } alHardwarePs1Voltage5vCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of alarm events for PS1 5v voltage." ::= { alStatsHardwareGlobal 11 } alHardwarePs1Voltage5vTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The sysUptime at the time of the last change of alarm status for PS1 5v voltage." ::= { alStatsHardwareGlobal 12 } alHardwarePs2Voltage3v OBJECT-TYPE SYNTAX Gauge32 UNITS "centivolts" MAX-ACCESS read-only STATUS current DESCRIPTION "The current 3V voltage of Power Supply 2 in centivolts." ::= { alStatsHardwareGlobal 13 } alHardwarePs2Voltage3vAlarm OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The alarm status for PS2 3v voltage. This alarm will fired when the 3v power supply 2 voltage is detected out of configured range." ::= { alStatsHardwareGlobal 14 } alHardwarePs2Voltage3vCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of alarm events for PS2 3v voltage." ::= { alStatsHardwareGlobal 15 } alHardwarePs2Voltage3vTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The sysUptime at the time of the last change of alarm status for PS2 3v voltage." ::= { alStatsHardwareGlobal 16 } alHardwarePs2Voltage5v OBJECT-TYPE SYNTAX Gauge32 UNITS "centivolts" MAX-ACCESS read-only STATUS current DESCRIPTION "The current 5V voltage of Power Supply 2 in centivolts." ::= { alStatsHardwareGlobal 17 } alHardwarePs2Voltage5vAlarm OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The alarm status for PS2 5v voltage. This alarm will fired when the 5v power supply 2 voltage is detected out of configured range." ::= { alStatsHardwareGlobal 18 } alHardwarePs2Voltage5vCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of alarm events for PS2 5v voltage." ::= { alStatsHardwareGlobal 19 } alHardwarePs2Voltage5vTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The sysUptime at the time of the last change of alarm status for PS2 5v voltage." ::= { alStatsHardwareGlobal 20 } alHardwareBoardVoltage3v OBJECT-TYPE SYNTAX Gauge32 UNITS "centivolts" MAX-ACCESS read-only STATUS current DESCRIPTION "The current 3V voltage of the mainboard in centivolts." ::= { alStatsHardwareGlobal 21 } alHardwareBoardVoltage3vAlarm OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The alarm status for the mainboard 3v voltage. This alarm will fired when the 3v mainboard voltage is detected out of configured range." ::= { alStatsHardwareGlobal 22 } alHardwareBoardVoltage3vCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of alarm events for the mainboard 3v voltage." ::= { alStatsHardwareGlobal 23 } alHardwareBoardVoltage3vTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The sysUptime at the time of the last change of alarm status for the mainboard 3v voltage." ::= { alStatsHardwareGlobal 24 } alHardwareBoardVoltage5v OBJECT-TYPE SYNTAX Gauge32 UNITS "centivolts" MAX-ACCESS read-only STATUS current DESCRIPTION "The current 5V voltage of the mainboard in centivolts." ::= { alStatsHardwareGlobal 25 } alHardwareBoardVoltage5vAlarm OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The alarm status for the mainboard 5v voltage. This alarm will fired when the 5v mainboard voltage is detected out of configured range." ::= { alStatsHardwareGlobal 26 } alHardwareBoardVoltage5vCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of alarm events for the mainboard 5v voltage." ::= { alStatsHardwareGlobal 27 } alHardwareBoardVoltage5vTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The sysUptime at the time of the last change of alarm status for the mainboard 5v voltage." ::= { alStatsHardwareGlobal 28 } alHardwareCpuTemp OBJECT-TYPE SYNTAX Integer32 (-40..120) UNITS "degrees Celsius" MAX-ACCESS read-only STATUS current DESCRIPTION "The current CPU temperature in degrees C." ::= { alStatsHardwareGlobal 29 } alHardwareCpuTempAlarm OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The alarm status for the CPU temperature. This alarm will fired when the CPU temperature is detected out of configured range." ::= { alStatsHardwareGlobal 30 } alHardwareCpuTempCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of alarm events for the CPU temperature." ::= { alStatsHardwareGlobal 31 } alHardwareCpuTempTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The sysUptime at the time of the last change of alarm status for the CPU temperature." ::= { alStatsHardwareGlobal 32 } alHardwareCageTemp OBJECT-TYPE SYNTAX Integer32 (-40..120) UNITS "degrees Celsius" MAX-ACCESS read-only STATUS current DESCRIPTION "The current cage temperature in degrees C." ::= { alStatsHardwareGlobal 33 } alHardwareCageTempAlarm OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The alarm status for the cage temperature. This alarm will fired when the cage temperature is detected out of configured range." ::= { alStatsHardwareGlobal 34 } alHardwareCageTempCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of alarm events for the cage temperature." ::= { alStatsHardwareGlobal 35 } alHardwareCageTempTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The sysUptime at the time of the last change of alarm status for the cage temperature." ::= { alStatsHardwareGlobal 36 } alHardwareFan1Rpm OBJECT-TYPE SYNTAX Gauge32 UNITS "RPM" MAX-ACCESS read-only STATUS current DESCRIPTION "The current speed of fan 1 in RPM." ::= { alStatsHardwareGlobal 37 } alHardwareFan1RpmAlarm OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The alarm status for fan 1 RPM. This alarm will fired when fan 1 RPM is detected out of configured range." ::= { alStatsHardwareGlobal 38 } alHardwareFan1RpmCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of alarm events for fan 1 RPM." ::= { alStatsHardwareGlobal 39 } alHardwareFan1RpmTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The sysUptime at the time of the last change of alarm status for fan 1 RPM." ::= { alStatsHardwareGlobal 40 } alHardwareFan2Rpm OBJECT-TYPE SYNTAX Gauge32 UNITS "RPM" MAX-ACCESS read-only STATUS current DESCRIPTION "The current speed of fan 2 in RPM." ::= { alStatsHardwareGlobal 41 } alHardwareFan2RpmAlarm OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The alarm status for fan 2 RPM. This alarm will fired when fan 2 RPM is detected out of configured range." ::= { alStatsHardwareGlobal 42 } alHardwareFan2RpmCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of alarm events for fan 2 RPM." ::= { alStatsHardwareGlobal 43 } alHardwareFan2RpmTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The sysUptime at the time of the last change of alarm status for fan 2 RPM." ::= { alStatsHardwareGlobal 44 } alHardwareFan3Rpm OBJECT-TYPE SYNTAX Gauge32 UNITS "RPM" MAX-ACCESS read-only STATUS current DESCRIPTION "The current speed of fan 3 in RPM." ::= { alStatsHardwareGlobal 45 } alHardwareFan3RpmAlarm OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The alarm status for fan 3 RPM. This alarm will fired when fan 3 RPM is detected out of configured range." ::= { alStatsHardwareGlobal 46 } alHardwareFan3RpmCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of alarm events for fan 3 RPM." ::= { alStatsHardwareGlobal 47 } alHardwareFan3RpmTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The sysUptime at the time of the last change of alarm status for fan 3 RPM." ::= { alStatsHardwareGlobal 48 } -- List of Current Hardware alHardwarePs1Type OBJECT-TYPE SYNTAX INTEGER { none(1), -- no power supply detected in slot ac(2) -- AC power supply detected in slot } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of power supply for Power Supply slot 1." ::= { alStatsHardwareGlobal 49 } alHardwarePs2Type OBJECT-TYPE SYNTAX INTEGER { none(1), -- no power supply detected in slot ac(2) -- AC power supply detected in slot } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of power supply for Power Supply slot 2." ::= { alStatsHardwareGlobal 50 } alHardwareSlot1Card OBJECT-TYPE SYNTAX ConcentratorCard MAX-ACCESS read-only STATUS current DESCRIPTION "The type of card in slot 1." ::= { alStatsHardwareGlobal 51 } alHardwareSlot2Card OBJECT-TYPE SYNTAX ConcentratorCard MAX-ACCESS read-only STATUS current DESCRIPTION "The type of card in slot 2." ::= { alStatsHardwareGlobal 52 } alHardwareSlot3Card OBJECT-TYPE SYNTAX ConcentratorCard MAX-ACCESS read-only STATUS current DESCRIPTION "The type of card in slot 3." ::= { alStatsHardwareGlobal 53 } alHardwareSlot4Card OBJECT-TYPE SYNTAX ConcentratorCard MAX-ACCESS read-only STATUS current DESCRIPTION "The type of card in slot 4." ::= { alStatsHardwareGlobal 54 } alHardwareSlot1Operational OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The operational status of card in slot 1." ::= { alStatsHardwareGlobal 55 } alHardwareSlot2Operational OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The operational status of card in slot 2." ::= { alStatsHardwareGlobal 56 } alHardwareSlot3Operational OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The operational status of card in slot 3." ::= { alStatsHardwareGlobal 57 } alHardwareSlot4Operational OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The operational status of card in slot 4." ::= { alStatsHardwareGlobal 58 } alHardwareRamSize OBJECT-TYPE SYNTAX Unsigned32 UNITS "MB" MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of memory, in MB on the concentrator." ::= { alStatsHardwareGlobal 59 } alHardwareChassis OBJECT-TYPE SYNTAX ConcentratorType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of VPN Concentrator this is." ::= { alStatsHardwareGlobal 60 } alHardwareCpuVoltageNominal OBJECT-TYPE SYNTAX Gauge32 UNITS "centivolts" MAX-ACCESS read-only STATUS current DESCRIPTION "The nominal CPU voltage in centivolts for the concentrator." ::= { alStatsHardwareGlobal 61 } alHardwareClientEthPrivSwitch OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Whether or not the 3002 Hardware Client has an Ethernet Switch for the private interface." ::= { alStatsHardwareGlobal 62 } alHardwareSerialNumber OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Unit serial number." ::= { alStatsHardwareGlobal 63 } altigaHardwareStatsMibConformance OBJECT IDENTIFIER ::= { altigaHardwareStatsMibModule 1 } altigaHardwareStatsMibCompliances OBJECT IDENTIFIER ::= { altigaHardwareStatsMibConformance 1 } altigaHardwareStatsMibCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for agents which implement the Altiga Hardware Statistics MIB." MODULE MANDATORY-GROUPS { altigaHardwareStatsGroup } ::= { altigaHardwareStatsMibCompliances 1 } altigaHardwareStatsGroup OBJECT-GROUP OBJECTS { alHardwareCpuVoltage, alHardwareCpuVoltageAlarm, alHardwareCpuVoltageCount, alHardwareCpuVoltageTime, alHardwarePs1Voltage3v, alHardwarePs1Voltage3vAlarm, alHardwarePs1Voltage3vCount, alHardwarePs1Voltage3vTime, alHardwarePs1Voltage5v, alHardwarePs1Voltage5vAlarm, alHardwarePs1Voltage5vCount, alHardwarePs1Voltage5vTime, alHardwarePs2Voltage3v, alHardwarePs2Voltage3vAlarm, alHardwarePs2Voltage3vCount, alHardwarePs2Voltage3vTime, alHardwarePs2Voltage5v, alHardwarePs2Voltage5vAlarm, alHardwarePs2Voltage5vCount, alHardwarePs2Voltage5vTime, alHardwareBoardVoltage3v, alHardwareBoardVoltage3vAlarm, alHardwareBoardVoltage3vCount, alHardwareBoardVoltage3vTime, alHardwareBoardVoltage5v, alHardwareBoardVoltage5vAlarm, alHardwareBoardVoltage5vCount, alHardwareBoardVoltage5vTime, alHardwareCpuTemp, alHardwareCpuTempAlarm, alHardwareCpuTempCount, alHardwareCpuTempTime, alHardwareCageTemp, alHardwareCageTempAlarm, alHardwareCageTempCount, alHardwareCageTempTime, alHardwareFan1Rpm, alHardwareFan1RpmAlarm, alHardwareFan1RpmCount, alHardwareFan1RpmTime, alHardwareFan2Rpm, alHardwareFan2RpmAlarm, alHardwareFan2RpmCount, alHardwareFan2RpmTime, alHardwareFan3Rpm, alHardwareFan3RpmAlarm, alHardwareFan3RpmCount, alHardwareFan3RpmTime, alHardwarePs1Type, alHardwarePs2Type, alHardwareSlot1Card, alHardwareSlot2Card, alHardwareSlot3Card, alHardwareSlot4Card, alHardwareSlot1Operational, alHardwareSlot2Operational, alHardwareSlot3Operational, alHardwareSlot4Operational, alHardwareRamSize, alHardwareChassis, alHardwareCpuVoltageNominal, alHardwareClientEthPrivSwitch, alHardwareSerialNumber } STATUS current DESCRIPTION "The objects for Hardware statistics." ::= { alHardwareGroup 2 } END