CISCO-ALPS-MIB -- ***************************************************************** -- ALPS-MIB.my: Airline Protocol Support MIB -- -- October 1997, Shantanu Sarkar & Mohan Tadisetty -- -- Copyright (c) 1997, 1998, 1999, 2000 by cisco Systems, Inc. -- ***************************************************************** CISCO-ALPS-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Counter32, Gauge32, IpAddress, TimeTicks, NOTIFICATION-TYPE FROM SNMPv2-SMI DisplayString, TEXTUAL-CONVENTION, TruthValue, RowStatus, TimeStamp, TimeInterval FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP -- NOTIFICATION-GROUP FROM SNMPv2-CONF ifIndex, InterfaceIndex FROM IF-MIB ciscoMgmt FROM CISCO-SMI; ciscoAlpsMIB MODULE-IDENTITY LAST-UPDATED "200001280000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W. Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-alps@cisco.com" DESCRIPTION "The MIB module for Airline Protocol Support. ************************************************************** * Acronym Definitions * * * * ALPS : AirLine Protocol Support * * AX.25 : Airline X.25 * * EMTOX : Exchange of Mixed Traffic over X.25 * * ASCU : Agent Set Control Unit * * * ************************************************************** Overview of ALPS (AirLine Protocol Support) MIB ============================================== MIB description Document to refer: 'Configuring ALPS' section in Cisco IOS Command Reference & Configuration Guide. The ALPS MIB provides configuration and operational information for Cisco's Airline protocol support for IBM-P1024B(ALC) and Unisys-P1024C(UTS) protocols encapsulation over TCP/IP. The following entities are managed: 1. Peers 2. ALPS Circuits 3. ASCUs (Agent Set Control Units) 4. ALC interface 5. ALPS Host link interface to the host HOST(Emtox/Ax.25) <----> Central <---> IP Network <---> Remote <----> ASCU router router The router connected to the Host is called the Central router and the router connected to the ASCU is called the Remote router. We anticipate one Central router connecting to a large number of Remote routers. Each router has a local peer, which connects to its counterpart on the other router (referred to as the remote peer) via a TCP connection. ALPS circuits are set up over this TCP connection either on a permanent or on-demand basis. A logical grouping of ASCUs are connected via a single circuit - this has no connection to the physical interfaces that the ASCUs are connected to. The only restriction is that all the ASCUs should be directly connected to the same router. Multiple ASCUs can connect to a single serial interface and several terminals connect to an ASCU. However, terminals are not visible to the ALPS feature - the router talks only to the ASCUs. An ASCU can be identified by * the interface it is on and its Interface Address (IA) or * the circuit it is on, and its A1 and A2 values, which identify it within the circuit. Thus there are two ways of identifying an ASCU - or Circuit names are globally unique. The connection to the host is via one of two flavors of X.25 - either AX.25 (for PVCs) or EMTOX (for SVCs). Each X.25 VC corresponds to one ALPS circuit. There are several hostlinks between a host and the Central router and load balancing is done across these. EMTOX allows the host to dial out to a terminal. This requires the use of an X.121 to IP address translation table to connect to the appropriate remote peer." REVISION "200001280000Z" DESCRIPTION "Modification for ALC and Service Message Enhancements" REVISION "9901070000Z" DESCRIPTION "Additional modifications to support ALPS/MATIP. NOTE: The alpsIfHLinkHostHld object has been updated to change its range. SMI (RFC2578 section 10.2 Extending an Information Module: Object Definitons) requires a new object defined and the old object obsoleted. This is also an index module which would require the old table to be obsoleted and a new one created. After review it has been decided to minimize impacts/disruptions to customer applications, we are not going to follow the SMI guidlines." REVISION "9812310000Z" DESCRIPTION "Modifications to support ALPS/MATIP." REVISION "9812080000Z" DESCRIPTION "Modifications to allow publishing." REVISION "9805200000Z" DESCRIPTION "Change ranges for some variables and update descriptions." ::= {ciscoMgmt 95 } X121Address ::= OCTET STRING (SIZE(0..17)) -- 0 to 17 bytes in length containing the ASCII -- characters [0-9], each octet contains one digit -- of the address. -- /***************************************/ -- The OBJECT IDENTIFIERS FOR ALPS MIBS -- /***************************************/ ciscoAlpsMIBObjects OBJECT IDENTIFIER ::= { ciscoAlpsMIB 1 } -- /***************************************/ -- The Global Object Declarations -- /***************************************/ AlpsCktName ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Specifies the ALPS Circuit Name. It is configured from the parser and is adminstratively assigned. This is globally unique." SYNTAX DisplayString (SIZE (1..12)) AlpsAscuA1A2Value ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Specifies A1 or A2 value of an ASCU. The A1 & A2 values together specify an ASCU within an ALPS circuit." SYNTAX INTEGER(0..255) -- ********************************************************************* -- * Define ALPS Local Peer -- ********************************************************************* alpsGroups OBJECT IDENTIFIER ::= { ciscoAlpsMIBObjects 1} alpsPeerObjects OBJECT IDENTIFIER ::= { ciscoAlpsMIBObjects 2 } alpsCktObjects OBJECT IDENTIFIER ::= { ciscoAlpsMIBObjects 3 } alpsIfObjects OBJECT IDENTIFIER ::= { ciscoAlpsMIBObjects 4 } alpsAscuObjects OBJECT IDENTIFIER ::= { ciscoAlpsMIBObjects 5 } alpsGlobalObjects OBJECT IDENTIFIER ::= { ciscoAlpsMIBObjects 6 } -- These MIB objects configure the local ALPS peer. The local peer -- connects to remote ALPS peers using a TCP/IP tunnel and sets -- up ALPS circuits across the tunnel. alpsPeer OBJECT IDENTIFIER ::= { alpsPeerObjects 1 } alpsPeerLocalIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The configured IP address used by the ALPS component in this router." ::= { alpsPeer 1 } alpsPeerLocalAtpPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The port number used locally by the ALPS peer at this router. This is a static value but the port number used can change in later versions. This is not a configured value but is embedded into the source code. This has been provided mainly to aid in debugging so that the operator knows which TCP port to look at. ATP is the ALPS Tunnelling Protocol, a Cisco proprietary way to tunnel ALPS data across a TCP link" ::= { alpsPeer 2 } alpsPeerKeepaliveTimeout OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP keep alive timeout value for Local ALPS Peer. Keepalives are sent out periodically at this interval to the remote peer." ::= { alpsPeer 3 } alpsPeerKeepaliveMaxRetries OBJECT-TYPE SYNTAX INTEGER(0..10) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of keepalives sent with acknowledgement before declaring the remote peer dead. 0 implies that keepalives are turned off." ::= { alpsPeer 4 } alpsPeerInCallsAcceptFlag OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "If this is true, calls are accepted from any peer. If this is false, calls are accepted only from those routers which have been explicitly configured using alps remote-peer commands." DEFVAL { false } ::= { alpsPeer 5 } -- ********************************************************************* -- Deprecated ALPS Remote Peer table -- ********************************************************************* alpsRemPeerTable OBJECT-TYPE SYNTAX SEQUENCE OF AlpsRemPeerEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "A list of Remote peers that the local ALPS peer can communicate with." ::= { alpsPeerObjects 2 } alpsRemPeerEntry OBJECT-TYPE SYNTAX AlpsRemPeerEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Each entry represents an Remote ALPS Peer." INDEX { alpsRemPeerIpAddr } ::= { alpsRemPeerTable 1 } AlpsRemPeerEntry ::= SEQUENCE { alpsRemPeerIpAddr IpAddress, alpsRemPeerConnType INTEGER, alpsRemPeerLocalPort INTEGER, alpsRemPeerRemotePort INTEGER, alpsRemPeerState INTEGER, alpsRemPeerUptime TimeTicks, alpsRemPeerNumActiveCkts Gauge32, alpsRemPeerIdleTimer TimeInterval, alpsRemPeerAlarmsEnabled TruthValue, alpsRemPeerTCPQlen INTEGER, alpsRemPeerOutPackets Counter32, alpsRemPeerOutOctets Counter32, alpsRemPeerInPackets Counter32, alpsRemPeerInOctets Counter32, alpsRemPeerDropsGiant Counter32, alpsRemPeerDropsQFull Counter32, alpsRemPeerDropsPeerUnreach Counter32, alpsRemPeerRowStatus RowStatus } alpsRemPeerIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The remote IP address for the TCP Connection." ::= { alpsRemPeerEntry 1 } alpsRemPeerConnType OBJECT-TYPE SYNTAX INTEGER { permanent(1), dynamic(2) } MAX-ACCESS read-create STATUS deprecated DESCRIPTION "Type of ALPS circuit established. Dynamic circuits are established only when there is data traffic that needs to be sent across and are closed when the alpsRemPeerIdleTimer expires. Permanent circuits stay up regardless of whether there is traffic across them or not." ::= { alpsRemPeerEntry 2 } alpsRemPeerLocalPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The port number used locally by the tcp connection for the circuit. the initiator of a connection will dynamically assign a port number. the other end of the connection will have a well-known port number applicable to the encapsulation used by the connection - e.g. the value of alpsPeerLocalAtpPort for ATP connections." ::= { alpsRemPeerEntry 3 } alpsRemPeerRemotePort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The port number used by the remote end of the tcp connection for the circuit. the initiator of a connection will dynamically assign a port number. the other end of the connection will have a well-known port number applicable to the encapsulation used by the connection - e.g. the value of alpsPeerLocalAtpPort for ATP connections. If this connection was initiated by the local router, a port number will be dynamically selected. Otherwise the value of alpsPeerLocalAtpPort will be used (for ATP connections)" ::= { alpsRemPeerEntry 4 } alpsRemPeerState OBJECT-TYPE SYNTAX INTEGER { closed(1), opening(2), opened(3) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION "TCP Peer State. Initially the connection is in the closed state. For permanent connections, it starts opening the TCP connection immediately, but for dynamic ones, it waits till there is traffic addressed to the remote peer. It then progresses via opening into the opened state." ::= { alpsRemPeerEntry 5 } alpsRemPeerUptime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Time elapsed since TCP connection was established." ::= { alpsRemPeerEntry 6 } alpsRemPeerNumActiveCkts OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Number of active ALPS circuits in this TCP session." ::= { alpsRemPeerEntry 7 } alpsRemPeerIdleTimer OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The TCP session with the peer will be closed if there is no activity for alpsInactiveTimer seconds. This is valid only for dynamic circuits" ::= { alpsRemPeerEntry 8 } alpsRemPeerAlarmsEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS deprecated DESCRIPTION "Specifies whether alarms are generated for this remote Peer" DEFVAL { false } ::= { alpsRemPeerEntry 9 } alpsRemPeerTCPQlen OBJECT-TYPE SYNTAX INTEGER (1..200) UNITS "packets" MAX-ACCESS read-create STATUS deprecated DESCRIPTION "Maximum TCP Queue size allowed for this TCP session." ::= { alpsRemPeerEntry 10 } alpsRemPeerOutPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Number of packets transmitted to the remote peer." ::= { alpsRemPeerEntry 11 } alpsRemPeerOutOctets OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Number of octets transmitted to the remote peer." ::= { alpsRemPeerEntry 12 } alpsRemPeerInPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Number of packets received from the remote peer." ::= { alpsRemPeerEntry 13 } alpsRemPeerInOctets OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Number of octets received from the remote peer." ::= { alpsRemPeerEntry 14 } alpsRemPeerDropsGiant OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Number of Packets dropped because they were larger than the maximum allowed packet size of 3840 bytes." ::= { alpsRemPeerEntry 15 } alpsRemPeerDropsQFull OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Number of packets dropped because the TCP queue (of size alpsRemPeerTCPQlen) was full." ::= { alpsRemPeerEntry 16 } alpsRemPeerDropsPeerUnreach OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Number of packets dropped because remote peer was unreachable." ::= { alpsRemPeerEntry 17 } alpsRemPeerRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS deprecated DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table." ::= { alpsRemPeerEntry 18 } -- ******************************************************************* -- Define ALPS Remote Peer Tables. -- -- The ALPS Remote Peer Tables are now split into two tables, -- one table for ALPS remote peer configurations and a second -- table for ALPS remote peer connections. The table for ALPS -- remote peer connections contains the objects that manage -- the TCP connections used by ALPS. The table for ALPS -- remote peer configuration objects contains the information -- that objects in the remote peer connection table use to -- configure themselves. The alpsRemPeerTable was deprecated -- and split into these 2 tables because ALPS/MATIP peer connections -- do not have a 1-to-1 mapping to an ALPS remote peer configuration -- object. Several ALPS/MATIP peer connections can use the same ALPS -- remote peer configuration, provided the ALPS/MATIP peer connections -- share the same remote peer IP address. -- ******************************************************************* -- *************************************** -- ALPS Remote Peer Configuration Table -- *************************************** alpsRemPeerCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF AlpsRemPeerCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table listing of all administered ALPS remote peer configuration entries on this node. Entries in this table can be created via a CLI command or via alpsRemPeerCfgRowStatus." ::= { alpsPeerObjects 3 } alpsRemPeerCfgEntry OBJECT-TYPE SYNTAX AlpsRemPeerCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry represents an ALPS remote peer configuration entry on this node." INDEX { alpsRemPeerCfgIpAddr, alpsRemPeerCfgProtocol } ::= { alpsRemPeerCfgTable 1 } AlpsRemPeerCfgEntry ::= SEQUENCE { alpsRemPeerCfgIpAddr IpAddress, alpsRemPeerCfgProtocol INTEGER, alpsRemPeerCfgActivation INTEGER, alpsRemPeerCfgTCPQLen INTEGER, alpsRemPeerCfgIdleTimer TimeInterval, alpsRemPeerCfgNoCircTimer TimeInterval, alpsRemPeerCfgAlarmsOn TruthValue, alpsRemPeerCfgStatIntvl TimeInterval, alpsRemPeerCfgStatRetry INTEGER, alpsRemPeerCfgRowStatus RowStatus } alpsRemPeerCfgIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The configured IP address of an ALPS remote peer." ::= { alpsRemPeerCfgEntry 1 } alpsRemPeerCfgProtocol OBJECT-TYPE SYNTAX INTEGER { atp(1), matipTypeA(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The configured ALPS protocol encapsulation. This protocol encapsulation is at the layer above TCP." ::= { alpsRemPeerCfgEntry 2 } alpsRemPeerCfgActivation OBJECT-TYPE SYNTAX INTEGER { permanent(1), dynamic(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The configured type of ALPS peer activation." ::= { alpsRemPeerCfgEntry 3 } alpsRemPeerCfgTCPQLen OBJECT-TYPE SYNTAX INTEGER (1..100) UNITS "packets" MAX-ACCESS read-create STATUS current DESCRIPTION "The configured maximum TCP Queue size." ::= { alpsRemPeerCfgEntry 4 } alpsRemPeerCfgIdleTimer OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-create STATUS current DESCRIPTION "The configured idle timer for a dynamic activation peer." ::= { alpsRemPeerCfgEntry 5 } alpsRemPeerCfgNoCircTimer OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-create STATUS current DESCRIPTION "The configured no-circuit timer for a dynamic activation peer." ::= { alpsRemPeerCfgEntry 6 } alpsRemPeerCfgAlarmsOn OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "The configured parameter which specifies whether alarms are generated for remote peer connections to the IP address in alpsRemPeerCfgIpAddr." DEFVAL { false } ::= { alpsRemPeerCfgEntry 7 } alpsRemPeerCfgStatIntvl OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-create STATUS current DESCRIPTION "The configured status interval timer." ::= { alpsRemPeerCfgEntry 8 } alpsRemPeerCfgStatRetry OBJECT-TYPE SYNTAX INTEGER (0..100) MAX-ACCESS read-create STATUS current DESCRIPTION "The configured number of status retries." ::= { alpsRemPeerCfgEntry 9 } alpsRemPeerCfgRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table." ::= { alpsRemPeerCfgEntry 10 } -- *************************************** -- ALPS Remote Peer Connection Table -- *************************************** alpsRemPeerConnTable OBJECT-TYPE SYNTAX SEQUENCE OF AlpsRemPeerConnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table listing of all ALPS remote peer connections on this node." ::= { alpsPeerObjects 4 } alpsRemPeerConnEntry OBJECT-TYPE SYNTAX AlpsRemPeerConnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry represents an ALPS remote peer connection on this node." INDEX { alpsRemPeerConnIpAddr, alpsRemPeerConnIdString } ::= { alpsRemPeerConnTable 1 } AlpsRemPeerConnEntry ::= SEQUENCE { alpsRemPeerConnIpAddr IpAddress, alpsRemPeerConnIdString DisplayString, alpsRemPeerConnLocalPort INTEGER, alpsRemPeerConnForeignPort INTEGER, alpsRemPeerConnState INTEGER, alpsRemPeerConnProtocol INTEGER, alpsRemPeerConnCreation INTEGER, alpsRemPeerConnActivation INTEGER, alpsRemPeerConnUptime TimeTicks, alpsRemPeerConnNumActCirc INTEGER, alpsRemPeerConnLastTxRx TimeStamp, alpsRemPeerConnLastRxAny TimeStamp, alpsRemPeerConnIdleTimer TimeInterval, alpsRemPeerConnNoCircTimer TimeInterval, alpsRemPeerConnTCPQLen INTEGER, alpsRemPeerConnAlarmsOn TruthValue, alpsRemPeerConnStatIntvl INTEGER, alpsRemPeerConnStatRetry INTEGER, alpsRemPeerConnDownReason INTEGER, alpsRemPeerConnOutPackets Counter32, alpsRemPeerConnOutOctets Counter32, alpsRemPeerConnInPackets Counter32, alpsRemPeerConnInOctets Counter32, alpsRemPeerConnDropsGiant Counter32, alpsRemPeerConnDropsQFull Counter32, alpsRemPeerConnDropsUnreach Counter32, alpsRemPeerConnDropsVersion Counter32 } alpsRemPeerConnIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address of the ALPS remote peer." ::= { alpsRemPeerConnEntry 1 } alpsRemPeerConnIdString OBJECT-TYPE SYNTAX DisplayString (SIZE (1..20)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A descriptive ASCII string that is used to distinguish among different peer connections to the same ALPS remote peer IP address." ::= { alpsRemPeerConnEntry 2 } alpsRemPeerConnLocalPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The local TCP port number used by the underlying TCP connection to an ALPS remote peer." ::= { alpsRemPeerConnEntry 3 } alpsRemPeerConnForeignPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The foreign (remote) TCP port number used by the underlying TCP connection to an ALPS remote peer." ::= { alpsRemPeerConnEntry 4 } alpsRemPeerConnState OBJECT-TYPE SYNTAX INTEGER { closed(1), opening(2), opened(3), busy(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the connection to an ALPS remote peer." ::= { alpsRemPeerConnEntry 5 } alpsRemPeerConnProtocol OBJECT-TYPE SYNTAX INTEGER { atp(1), matipTypeA(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The ALPS protocol encapsulation used on the connection to the ALPS remote peer. This protocol encapsulation is a layer above TCP." ::= { alpsRemPeerConnEntry 6 } alpsRemPeerConnCreation OBJECT-TYPE SYNTAX INTEGER { admin(1), learned(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The stimulus for creating the peer connection object. The peer connection object may be created solely due to configuration (admin) or due to a combination of configuration and protocol events (learned)." ::= { alpsRemPeerConnEntry 7 } alpsRemPeerConnActivation OBJECT-TYPE SYNTAX INTEGER { permanent(1), dynamic(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Basis for activation a peer connection. A permanent activation peer connection will attempt to open immediately and stay open, regardless of the usage of the peer connection. A dynamic activation peer connection only opens when there is data to send and the peer connection will close if there are no data messages sent or received across the peer for the duration of the idle timer." ::= { alpsRemPeerConnEntry 8 } alpsRemPeerConnUptime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Elapsed time since the ALPS peer connection was successfully established." ::= { alpsRemPeerConnEntry 9 } alpsRemPeerConnNumActCirc OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ALPS virtual circuits using the connection to this ALPS remote peer." ::= { alpsRemPeerConnEntry 10 } alpsRemPeerConnLastTxRx OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime when a peer data message was last transmitted or received across this ALPS remote peer connection. This timestamp is not update if the peer message is a peer status inquiry/response message." ::= { alpsRemPeerConnEntry 11 } alpsRemPeerConnLastRxAny OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime when a peer data or status message is last received across the ALPS remote peer connection." ::= { alpsRemPeerConnEntry 12 } alpsRemPeerConnIdleTimer OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-only STATUS current DESCRIPTION "A dynamic activation ALPS peer connection will be closed if zero peer data messages are sent or received for a length of time greater than or equal to this timer." ::= { alpsRemPeerConnEntry 13 } alpsRemPeerConnNoCircTimer OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-only STATUS current DESCRIPTION "A dynamic activation ALPS peer connection will be closed if zero ALPS circuits are active or attempt to activate for a length of time greater than or equal to this timer." ::= { alpsRemPeerConnEntry 14 } alpsRemPeerConnTCPQLen OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of ALPS peer messages that can be queued in a single TCP session." ::= { alpsRemPeerConnEntry 15 } alpsRemPeerConnAlarmsOn OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This parameter specifies whether ALPS alarms are generated for this ALPS remote peer connection." ::= { alpsRemPeerConnEntry 16 } alpsRemPeerConnStatIntvl OBJECT-TYPE SYNTAX INTEGER (0..300) MAX-ACCESS read-only STATUS current DESCRIPTION "The time interval (in seconds) between transmission of consecutive ALPS Peer Status messages. These messages are only transmitted if zero messages are received on the peer connection for a length of time greater than or equal to this timer." ::= { alpsRemPeerConnEntry 17 } alpsRemPeerConnStatRetry OBJECT-TYPE SYNTAX INTEGER (0..100) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of consecutive unanswered ALPS Peer Status messages transmitted before closing the conenction to the ALPS remote peer." ::= { alpsRemPeerConnEntry 18 } alpsRemPeerConnDownReason OBJECT-TYPE SYNTAX INTEGER { unknown(1), idle(2), noCircuits(3), destUnreachable(4), foreignReset(5), localReset(6), noMemory(7), openingTimeout(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "Reason that an ALPS Peer connection failed to open sauccessfully." ::= { alpsRemPeerConnEntry 19 } alpsRemPeerConnOutPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets transmitted on this ALPS remote peer connection." ::= { alpsRemPeerConnEntry 20 } alpsRemPeerConnOutOctets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of octets transmitted on this ALPS remote peer connection." ::= { alpsRemPeerConnEntry 21 } alpsRemPeerConnInPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets received on this ALPS remote peer connection." ::= { alpsRemPeerConnEntry 22 } alpsRemPeerConnInOctets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of octets received on this ALPS remote peer connection." ::= { alpsRemPeerConnEntry 23 } alpsRemPeerConnDropsGiant OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of ALPS peer packets dropped due to exceeding the maximum allowed packet size of 3840 bytes." ::= { alpsRemPeerConnEntry 24 } alpsRemPeerConnDropsQFull OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of ALPS peer packets dropped because the TCP output queue is full." ::= { alpsRemPeerConnEntry 25 } alpsRemPeerConnDropsUnreach OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of ALPS peer packets dropped because the ALPS remote peer is unreachable." ::= { alpsRemPeerConnEntry 26 } alpsRemPeerConnDropsVersion OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of ALPS peer packets dropped because of a version mismatch in the ALPS encapsulation." ::= { alpsRemPeerConnEntry 27 } -- ********************************************************************* -- Define ALPS Circuit tables - these are also organised into a base -- table and a dlc-type specific table (X25 or P1024) -- Similar to the Peer tables, these would contain configured circuits at -- the remote router and entries for dynamically created circuits at the -- Central router -- ********************************************************************* alpsCktBaseTable OBJECT-TYPE SYNTAX SEQUENCE OF AlpsCktBaseEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of ALPS circuits. This table contains variables common to central & remote routers." ::= { alpsCktObjects 1 } alpsCktBaseEntry OBJECT-TYPE SYNTAX AlpsCktBaseEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Details of ALPS Circuits." INDEX { alpsCktBaseName, alpsCktBaseDlcType } ::= { alpsCktBaseTable 1 } AlpsCktBaseEntry ::= SEQUENCE { alpsCktBaseName AlpsCktName, alpsCktBaseDlcType INTEGER, alpsCktBasePriPeerAddr IpAddress, alpsCktBaseAlarmsEnabled TruthValue, alpsCktBaseConnType INTEGER, alpsCktBaseState INTEGER, alpsCktBaseNumActiveAscus INTEGER, alpsCktBaseCurrentPeer IpAddress, alpsCktBaseLifeTimeTimer TimeInterval, alpsCktBaseHostLinkNumber INTEGER, alpsCktBaseHostLinkType INTEGER, alpsCktBaseRemHld INTEGER, alpsCktBaseLocalHld INTEGER, alpsCktBaseDownReason INTEGER, alpsCktBaseOutPackets Counter32, alpsCktBaseOutOctets Counter32, alpsCktBaseInPackets Counter32, alpsCktBaseInOctets Counter32, alpsCktBaseDropsCktDisabled Counter32, alpsCktBaseDropsQOverflow Counter32, alpsCktBaseDropsLifeTimeExpd Counter32, alpsCktBaseEnabled TruthValue, alpsCktBaseRowStatus RowStatus, alpsCktBaseCurrPeerConnId DisplayString } alpsCktBaseName OBJECT-TYPE SYNTAX AlpsCktName MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the ALPS Circuit Name. This is unique within the network." ::= { alpsCktBaseEntry 1 } alpsCktBaseDlcType OBJECT-TYPE SYNTAX INTEGER { emtox(1), ax25(2), alc(3), uts(4) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies what type of circuit this is. The X25 circuit is set up with the same name as the P1024 circuit so we need this variable to distinguish between the two, in case local switching is done." ::= { alpsCktBaseEntry 2 } alpsCktBasePriPeerAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "This is the IP address of the Primary Central peer. It is mandatory to configure a primary peer, but the backup peer is optional." ::= { alpsCktBaseEntry 3 } alpsCktBaseAlarmsEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies whether alarms are generated for this ALPS circuit. Alarms can be syslog messages or SNMP traps - both are controlled using the same flags." DEFVAL { false } ::= { alpsCktBaseEntry 4 } alpsCktBaseConnType OBJECT-TYPE SYNTAX INTEGER { permanent(1), dynamic(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the ALPS Circuit Connection Type." ::= { alpsCktBaseEntry 5 } alpsCktBaseState OBJECT-TYPE SYNTAX INTEGER { disabled(1), inoperable(2), opening(3), opened(4), cktBusy(5), peerBusy(6), updating(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the state of ALPS Circuit." ::= { alpsCktBaseEntry 6 } alpsCktBaseNumActiveAscus OBJECT-TYPE SYNTAX INTEGER (0..64) MAX-ACCESS read-only STATUS current DESCRIPTION "Reports the number of enabled ASCUs that are attached to this ALPS Circuit. Attachment of an ASCU to an ALPS circuit may occur due to configuration or due to information passed in a protocol message." ::= { alpsCktBaseEntry 7 } alpsCktBaseCurrentPeer OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Reports the IP address of the peer that this ALPS circuit is currently connected to. " ::= { alpsCktBaseEntry 8 } alpsCktBaseLifeTimeTimer OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-create STATUS current DESCRIPTION "A data message that has been queued within the router for longer than this interval will be dropped." ::= { alpsCktBaseEntry 9 } alpsCktBaseHostLinkNumber OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies host link number (on Central router) for this ALPS Circuit. The host link number is used to provide a degree of transparency to the remote router. A single host link may correspond to multiple physical links between the central router and the host, which can then load-balance VCs across them." ::= { alpsCktBaseEntry 10 } alpsCktBaseHostLinkType OBJECT-TYPE SYNTAX INTEGER { ax25(1), emtox(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies host link type(on Central router) for this ALPS Circuit." ::= { alpsCktBaseEntry 11 } alpsCktBaseRemHld OBJECT-TYPE SYNTAX INTEGER(1..32639) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the HLD (High-level descriptor) of the AX.25/EMTOX host for this ALPS Circuit. This serves as an identifier for the host" ::= { alpsCktBaseEntry 12 } alpsCktBaseLocalHld OBJECT-TYPE SYNTAX INTEGER(1..32639) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the local HLD for this ALPS Circuit. HLDs are required at the host for both ends of the connection." ::= { alpsCktBaseEntry 13 } alpsCktBaseDownReason OBJECT-TYPE SYNTAX INTEGER { unknown(1), noReason(2), hostLinkDown(3), cktDisabled(4), hostLinkDisabled(5), noHostLinkMatched(6), noHldMatched(7), cktNameInUse(8), pvcLcnOutOfRange(9), x25ParamInvalid(10), cktOpeningTimeout(11), x25ClearDteNoReason(12), configMismatch(13), noResourcesAvail(14), incompatibleA1A2(15), cktIdle(16), peerDown(17), noAscusConfigured(18), x25ClearHostUnknown(19), x25ClearHostDown(20), x25ClearHostDisabled(21), x25ClearHostSaturated(22), x25ClearCallerUnknown(23), x25ClearCallerUnauth(24), x25ClearConfigRejected(25), x25ClearConfigFallback(26), x25ClearConfigIncompat(27), x25ClearHLDUnknown(28), x25ClearPIDUnknown(29), x25ClearFacilRejected(30), x25ClearNetNoReason(31), pvcLcnInUse(32), noSvcLcnAvail(33), peerIdle(34), presUnknown(35), presMismatch(36), openMsgTooShort(37), mpxUnknown(38), mpxHdrMismatch(39), trafTypeMismatch(40), codingMismatch(41), ascuInSession(42) } MAX-ACCESS read-only STATUS current DESCRIPTION "Reports the reason why this ALPS Circuit is down, if it is down." DEFVAL { noReason } ::= { alpsCktBaseEntry 14 } alpsCktBaseOutPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets transmitted to remote peer over this circuit." ::= { alpsCktBaseEntry 15 } alpsCktBaseOutOctets OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of octets transmitted to remote peer over this circuit." ::= { alpsCktBaseEntry 16 } alpsCktBaseInPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets received from remote peer over this circuit." ::= { alpsCktBaseEntry 17 } alpsCktBaseInOctets OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of octets received from remote peer over this circuit." ::= { alpsCktBaseEntry 18 } alpsCktBaseDropsCktDisabled OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets dropped because the circuit was disabled. This would typically be packets that were queueued before the circuit was disabled which are now left in the queue." ::= { alpsCktBaseEntry 19 } alpsCktBaseDropsQOverflow OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets dropped due to TCP Congestion." ::= { alpsCktBaseEntry 20 } alpsCktBaseDropsLifeTimeExpd OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets which were queued within the router for longer than alpsCktBaseLifeTimeTimer." ::= { alpsCktBaseEntry 21 } alpsCktBaseEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This specifies if the circuit has been enabled. After a circuit has been configured, it must be explicitly enabled in order for the circuit to be set up." DEFVAL { false } ::= { alpsCktBaseEntry 22 } alpsCktBaseRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table." ::= { alpsCktBaseEntry 23 } alpsCktBaseCurrPeerConnId OBJECT-TYPE SYNTAX DisplayString (SIZE (1..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "A descriptive ASCII string that is used to distinguish among different peer connections to the same ALPS remote peer IP address." ::= { alpsCktBaseEntry 24 } -- -- X.25 ckt Table -- alpsCktX25Table OBJECT-TYPE SYNTAX SEQUENCE OF AlpsCktX25Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of ALPS X.25 circuits. These entries exist only for X.25 circuits. hence this table would probably be empty at the remote router" ::= { alpsCktObjects 2 } alpsCktX25Entry OBJECT-TYPE SYNTAX AlpsCktX25Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Details of ALPS Circuits." INDEX { alpsCktBaseName, alpsCktX25DlcType } ::= { alpsCktX25Table 1 } AlpsCktX25Entry ::= SEQUENCE { alpsCktX25DlcType INTEGER, alpsCktX25IfIndex InterfaceIndex, alpsCktX25LCN INTEGER, alpsCktX25HostX121 X121Address, alpsCktX25RemoteX121 X121Address, alpsCktX25DropsVcReset Counter32 } alpsCktX25DlcType OBJECT-TYPE SYNTAX INTEGER { emtox(1), ax25(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies what type of circuit this is." ::= { alpsCktX25Entry 1 } alpsCktX25IfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Reports the interface the circuit is on. This is the interface which is connected to the host" ::= { alpsCktX25Entry 2 } alpsCktX25LCN OBJECT-TYPE SYNTAX INTEGER (1..4096) MAX-ACCESS read-only STATUS current DESCRIPTION "The Logical Channel Number being used on the X.25 VC for this ALPS Circuit." ::= { alpsCktX25Entry 3 } alpsCktX25HostX121 OBJECT-TYPE SYNTAX X121Address MAX-ACCESS read-only STATUS current DESCRIPTION "The X.121 address on the host side which the central router uses to connect to the host" ::= { alpsCktX25Entry 4 } alpsCktX25RemoteX121 OBJECT-TYPE SYNTAX X121Address MAX-ACCESS read-only STATUS current DESCRIPTION "X.121 address of the remote side. Remote here refers to the side that the ASCUS are connected to and is also referred to as the remote router." ::= { alpsCktX25Entry 5 } alpsCktX25DropsVcReset OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets dropped due to the VC being reset. These are packets that were queued up for transmission on that VC when it was reset" ::= { alpsCktX25Entry 6 } -- -- P1024 (ALC or UTS) Circuit Table -- alpsCktP1024Table OBJECT-TYPE SYNTAX SEQUENCE OF AlpsCktP1024Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of ALC or UTS Alps circuits." ::= { alpsCktObjects 3 } alpsCktP1024Entry OBJECT-TYPE SYNTAX AlpsCktP1024Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Details of ALPS Circuits." INDEX { alpsCktBaseName, alpsCktP1024DlcType } ::= { alpsCktP1024Table 1 } AlpsCktP1024Entry ::= SEQUENCE { alpsCktP1024DlcType INTEGER, alpsCktP1024BackupPeerAddr IpAddress, alpsCktP1024RetryTimer TimeInterval, alpsCktP1024IdleTimer TimeInterval, alpsCktP1024EmtoxX121 X121Address, alpsCktP1024Ax25LCN INTEGER, alpsCktP1024WinOut INTEGER, alpsCktP1024WinIn INTEGER, alpsCktP1024OutPktSize INTEGER, alpsCktP1024InPktSize INTEGER, alpsCktP1024SvcMsgList INTEGER, alpsCktP1024SvcMsgIntvl TimeTicks, alpsCktP1024DropsUnkAscu Counter32, alpsCktP1024RowStatus RowStatus, alpsCktP1024MatipCloseDelay TimeInterval } alpsCktP1024DlcType OBJECT-TYPE SYNTAX INTEGER { alc(3), uts(4) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies what type of circuit this is. " ::= { alpsCktP1024Entry 1 } alpsCktP1024BackupPeerAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "This is the IP address of the backup remote peer. This is optional and hence may not always exist." ::= { alpsCktP1024Entry 2 } alpsCktP1024RetryTimer OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the interval at which a permanent ALPS circuit will attempt to reestablish the circuit in case it wasn't able to come up." ::= { alpsCktP1024Entry 3 } alpsCktP1024IdleTimer OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-create STATUS current DESCRIPTION "If there is no traffic on a dynamic ALPS circuit for this interval, it will be cleared." ::= { alpsCktP1024Entry 4 } alpsCktP1024EmtoxX121 OBJECT-TYPE SYNTAX X121Address MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the X.121 address of the SVC established with EMTOX host. This field should be set to length zero in the case of PVCs (AX.25 host)." ::= { alpsCktP1024Entry 5 } alpsCktP1024Ax25LCN OBJECT-TYPE SYNTAX INTEGER (0..4096) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the Logical Channel Number being used on the PVC established with AX.25 host. This field should be set to zero in the case of SVCs (EMTOX host)." ::= { alpsCktP1024Entry 6 } alpsCktP1024WinOut OBJECT-TYPE SYNTAX INTEGER (1..7) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies X.25 transmit Window size on the Logical Channel Number of this ALPS Circuit." ::= { alpsCktP1024Entry 7 } alpsCktP1024WinIn OBJECT-TYPE SYNTAX INTEGER (1..7) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the X.25 receive Window size on the Logical Channel Number of this ALPS Circuit." ::= { alpsCktP1024Entry 8 } alpsCktP1024OutPktSize OBJECT-TYPE SYNTAX INTEGER (128..4096) UNITS "bytes" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the X.25 maxiumum output Packet size on the Logical Channel Number of this ALPS Circuit. The default output Packet size for AX.25 is 240 bytes and 128 bytes for EMTOX." ::= { alpsCktP1024Entry 9 } alpsCktP1024InPktSize OBJECT-TYPE SYNTAX INTEGER (128..4096) UNITS "bytes" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies X.25 maximum input Packet size on the Logical Channel Number of this ALPS Circuit. The default input Packet size for AX.25 is 240 bytes and 128 bytes for EMTOX." ::= { alpsCktP1024Entry 10 } alpsCktP1024SvcMsgList OBJECT-TYPE SYNTAX INTEGER (0..8) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the Service Message List Number to use on this ALPS Circuit. This allows custom service messages to be sent for ASCUs on a particular circuit. Service messages are sent out by the router to the ASCU when abnormal conditions occur, and are displayed on the terminal. There is a default set of service messages, usually referred to as List 0. However, it is possible to configure custom sets of service messages for display, selectable on a per-circuit basis." DEFVAL { 0 } ::= { alpsCktP1024Entry 11 } alpsCktP1024SvcMsgIntvl OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies Service Message Time Interval for the Service messages to be sent this ALPS Circuit. This controls how frequently the messages are repeated when an error condition (e.g. network being down) persists." ::= { alpsCktP1024Entry 12 } alpsCktP1024DropsUnkAscu OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets that were found to be from an Unknown ASCU (i.e. an ASCU that had not been configured) and hence were dropped." ::= { alpsCktP1024Entry 13 } alpsCktP1024RowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table." ::= { alpsCktP1024Entry 14 } alpsCktP1024MatipCloseDelay OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the minumum delay between transmission of a MATIP Close and the transmission of a MATIP Session Open for this ALPS circuit." ::= { alpsCktP1024Entry 15 } -- ********************************************************************* -- * ALPS ASCU Object at Central & Remote routers. This -- ********************************************************************* alpsCktAscuTable OBJECT-TYPE SYNTAX SEQUENCE OF AlpsCktAscuEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of ASCUs for each ALPS Circuit. This may not include all ASCUs which have this circuit configured as alpsAscuCktName because some ASCUs may be rejected by the host while setting up the circuit." ::= {alpsCktObjects 4 } alpsCktAscuEntry OBJECT-TYPE SYNTAX AlpsCktAscuEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Details of ASCUs on ASCU Circuits." INDEX { alpsCktAscuCktName, alpsCktAscuCktDlcType, alpsCktAscuA1, alpsCktAscuA2 } ::= { alpsCktAscuTable 1 } AlpsCktAscuEntry ::= SEQUENCE { alpsCktAscuCktName AlpsCktName, alpsCktAscuCktDlcType INTEGER, alpsCktAscuA1 AlpsAscuA1A2Value, alpsCktAscuA2 AlpsAscuA1A2Value, alpsCktAscuIfIndex InterfaceIndex, alpsCktAscuId INTEGER, alpsCktAscuStatus INTEGER } alpsCktAscuCktName OBJECT-TYPE SYNTAX AlpsCktName MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of the ALPS circuit which this ASCU is on. The circuit may be always up (for permanent circuits) or get set up (dynamic circuits) when there is traffic on one of the ASCUs which are set up for that circuit." ::= { alpsCktAscuEntry 1 } alpsCktAscuCktDlcType OBJECT-TYPE SYNTAX INTEGER { emtox(1), ax25(2), alc(3), uts(4) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies what type of circuit this is. The X.25 circuit is set up with the same name as the ALC circuit so we need this variable to distinguish between the two." ::= { alpsCktAscuEntry 2 } alpsCktAscuA1 OBJECT-TYPE SYNTAX AlpsAscuA1A2Value MAX-ACCESS not-accessible STATUS current DESCRIPTION "A1 value. This is used along with the alpsCktAscuA2 value to identify the ASCU within the circuit." ::= { alpsCktAscuEntry 3 } alpsCktAscuA2 OBJECT-TYPE SYNTAX AlpsAscuA1A2Value MAX-ACCESS not-accessible STATUS current DESCRIPTION "A2 value. This is used along with the alpsCktAscuA1 value to identify the ASCU within the circuit." ::= { alpsCktAscuEntry 4 } alpsCktAscuIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Reports the interface the ASCU is on. This field, along with alpsCktAscuId is provided so that it is possible to correlate this information with the configured ASCU information in alpsAscuTable" ::= { alpsCktAscuEntry 5 } alpsCktAscuId OBJECT-TYPE SYNTAX INTEGER (0..127) MAX-ACCESS read-only STATUS current DESCRIPTION "Reports the ASCU Identifier which uniquely identifies an ASCU on a given interface. This value is the Interface Address (IA) for ALC and the Remote Identifier (RID) for UTS. A value of 0 indicates that the ASCU id is either unavailable or not applicable." ::= { alpsCktAscuEntry 6 } alpsCktAscuStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), ok(2), reject(3), new(4), pending(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Reports the ASCU status - ASCUs configured on the circuit can be rejected at the host and would then be marked REJECT. Also, ASCUs configured after the circuit has been established are not added dynamically to the circuit but are marked NEW and get added when the circuit gets established the next time. ASCUs waiting for an accept or reject response from the host are marked as PENDING. ASCUs that were accepted by the host are marked OK." ::= { alpsCktAscuEntry 7 } -- ********************************************************************* -- * ALPS P1024 Interface Object - Interface Table -- ********************************************************************* alpsIfP1024Table OBJECT-TYPE SYNTAX SEQUENCE OF AlpsIfP1024Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of interfaces running the P1024B or P1024C protocols" ::= { alpsIfObjects 1 } alpsIfP1024Entry OBJECT-TYPE SYNTAX AlpsIfP1024Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Interface Details" INDEX { ifIndex } ::= { alpsIfP1024Table 1 } AlpsIfP1024Entry ::= SEQUENCE { alpsIfP1024EncapType INTEGER, alpsIfP1024PollRespTimeout TimeInterval, alpsIfP1024GATimeout TimeInterval, alpsIfP1024PollPauseTimeout TimeInterval, alpsIfP1024MaxErrCnt INTEGER, alpsIfP1024MaxRetrans INTEGER, alpsIfP1024CurrErrCnt INTEGER, alpsIfP1024MinGoodPollResp INTEGER, alpsIfP1024PollingRatio INTEGER, alpsIfP1024NumAscus Gauge32, alpsIfP1024ServMsgFormat INTEGER, alpsIfP1024ServMsgStatusChange TruthValue, alpsIfP1024ServMsgDropTermAddr INTEGER } alpsIfP1024EncapType OBJECT-TYPE SYNTAX INTEGER { alc(1), uts(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Reports the encapsulation type for this Serial Interface." ::= { alpsIfP1024Entry 1 } alpsIfP1024PollRespTimeout OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the Poll Response Time out value." DEFVAL { 500 } ::= { alpsIfP1024Entry 2 } alpsIfP1024GATimeout OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the time-out delay between receipt of first character of an input sequence solicited by a poll and receipt of GA sequence." DEFVAL { 600 } ::= { alpsIfP1024Entry 3 } alpsIfP1024PollPauseTimeout OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the minimum delay between two poll cycles. Thus the poll pause interval is counted from the instant when the first ASCU in the poll list is polled. Note that this is the delay between two traversals of the entire poll list rather than the interval between two consecutive polls. The actual delay will probably be more than the value of this variable." DEFVAL { 50 } ::= { alpsIfP1024Entry 4 } alpsIfP1024MaxErrCnt OBJECT-TYPE SYNTAX INTEGER (0..30) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies a maximum error count for this interface. After an ASCU link comes up, if it experiences this number of errors the ASCU link will be shutdown. The default value of 0 results in the ASCU link never being shutdown." DEFVAL { 0 } ::= { alpsIfP1024Entry 5 } alpsIfP1024MaxRetrans OBJECT-TYPE SYNTAX INTEGER (0..10) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the maximum number of times an output message will be retransmitted before it is discarded. This is relevant only for P1024C (UTS). For ALC, a value of 0 will be returned. Note that legal values for UTS are 1-10" DEFVAL { 3 } ::= { alpsIfP1024Entry 6 } alpsIfP1024CurrErrCnt OBJECT-TYPE SYNTAX INTEGER (0..30) MAX-ACCESS read-only STATUS current DESCRIPTION "Reports the number of errors currently existing for this ASCU link. When this equals alpsIfP1024MaxErrCnt then the ASCU link will be shut down, unless alpsIfP1024MaxErrCnt equals 0 in which case the ascu link is never shut down due to error thresholds being exceeded" DEFVAL { 0 } ::= { alpsIfP1024Entry 7 } alpsIfP1024MinGoodPollResp OBJECT-TYPE SYNTAX INTEGER (1..30) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the number of good Poll Responses to be received from an ASCU before it can be declared up." DEFVAL { 1 } ::= { alpsIfP1024Entry 8 } alpsIfP1024PollingRatio OBJECT-TYPE SYNTAX INTEGER (1..30) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies how many times ASCUs in UP state are polled before an ASCU in DOWN state is polled again." DEFVAL { 30 } ::= { alpsIfP1024Entry 9 } alpsIfP1024NumAscus OBJECT-TYPE SYNTAX Gauge32 UNITS "Ascus" MAX-ACCESS read-only STATUS current DESCRIPTION "Reports the number of ASCUs configured on this Serial Port." DEFVAL { 0 } ::= { alpsIfP1024Entry 10 } alpsIfP1024ServMsgFormat OBJECT-TYPE SYNTAX INTEGER { sita(1), apollo(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the format of the service message sent to an ASCU on this interface." DEFVAL { sita } ::= { alpsIfP1024Entry 11 } alpsIfP1024ServMsgStatusChange OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies whether service messages generated due to an ALPS circuit status change or an ASCU status change, will be forwarded to the ASCU." DEFVAL { true } ::= { alpsIfP1024Entry 12 } alpsIfP1024ServMsgDropTermAddr OBJECT-TYPE SYNTAX INTEGER { msgterm(1), configterm(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies whether the service message will be sent to the same terminal address of the dropped message or the configured value." DEFVAL { configterm } ::= { alpsIfP1024Entry 13 } -- ********************************************************************* -- * ALPS Host Link Interface Object -- ********************************************************************* alpsIfHLinkTable OBJECT-TYPE SYNTAX SEQUENCE OF AlpsIfHLinkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of interfaces running AX.25/EMTOX host link protocols. These are on the central router" ::= { alpsIfObjects 2 } alpsIfHLinkEntry OBJECT-TYPE SYNTAX AlpsIfHLinkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Details of AX.25/EMTOX host link protocols on an Interface." INDEX { ifIndex , alpsIfHLinkHostHld, alpsIfHLinkNumber } ::= { alpsIfHLinkTable 1 } AlpsIfHLinkEntry ::= SEQUENCE { alpsIfHLinkHostHld INTEGER, alpsIfHLinkNumber INTEGER, alpsIfHLinkX25ProtocolType INTEGER, alpsIfHLinkAx25PvcDamp TimeInterval, alpsIfHLinkEmtoxHostX121 X121Address, alpsIfHLinkActiveCkts INTEGER } alpsIfHLinkHostHld OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the HLD of the AX.25/EMTOX host connected on this Interface. The HLD(High-level descriptor) serves as an identifier along with the hostlink number and helps correlate the ALPS circuit to a host link. The hex range is 0x1 to 0xFFFF which corresponds to 1 ... 65535 in decimal." ::= { alpsIfHLinkEntry 1 } alpsIfHLinkNumber OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the configured Host Link Number on this Serial Interface." ::= { alpsIfHLinkEntry 2 } alpsIfHLinkX25ProtocolType OBJECT-TYPE SYNTAX INTEGER { ax25(1), emtox(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Reports the encapsulation type for this Serial Interface - AX.25 or EMTOX." ::= { alpsIfHLinkEntry 3 } alpsIfHLinkAx25PvcDamp OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-only STATUS current DESCRIPTION "The purpose of this object is to handle the link-damping for an AX.25 host. If the PVC goes inactive (i.e. link goes down, etc...) for PVCDampValue seconds, then PVC will be destroyed as well as the associated ALPS circuit." ::= { alpsIfHLinkEntry 4 } alpsIfHLinkEmtoxHostX121 OBJECT-TYPE SYNTAX X121Address MAX-ACCESS read-only STATUS current DESCRIPTION "Specfies the X.121 address of this EMTOX host." ::= { alpsIfHLinkEntry 5 } alpsIfHLinkActiveCkts OBJECT-TYPE SYNTAX INTEGER (0..4096) UNITS "circuits" MAX-ACCESS read-only STATUS current DESCRIPTION "Reports the number of ALPS Ckts established with this host." ::= { alpsIfHLinkEntry 6 } -- ********************************************************************* -- * Define ALPS ASCU Object -- ********************************************************************* alpsAscuTable OBJECT-TYPE SYNTAX SEQUENCE OF AlpsAscuEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of ALPS ASCUs on an interface. This is defined only at the remote router." ::= { alpsAscuObjects 1 } alpsAscuEntry OBJECT-TYPE SYNTAX AlpsAscuEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Details of ASCU." INDEX { ifIndex, alpsAscuId } ::= { alpsAscuTable 1 } AlpsAscuEntry ::= SEQUENCE { alpsAscuId INTEGER, alpsAscuA1 AlpsAscuA1A2Value, alpsAscuA2 AlpsAscuA1A2Value, alpsAscuCktName AlpsCktName, alpsAscuAlarmsEnabled TruthValue, alpsAscuRetryOption INTEGER, alpsAscuMaxMsgLength INTEGER, alpsAscuFwdStatusOption TruthValue, alpsAscuState INTEGER, alpsAscuDownReason INTEGER, alpsAscuOutPackets Counter32, alpsAscuOutOctets Counter32, alpsAscuInPackets Counter32, alpsAscuInOctets Counter32, alpsAscuDropsGarbledPkts Counter32, alpsAscuDropsAscuDown Counter32, alpsAscuDropsAscuDisabled Counter32, alpsAscuEnabled TruthValue, alpsAscuRowStatus RowStatus, alpsAscuAutoReset TruthValue } alpsAscuId OBJECT-TYPE SYNTAX INTEGER(1..127) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the ASCU Identifier and uniquely identifies an ASCU on a given interface. This value is the Interface Address (IA) for ALC and the Remote Identifier (RID) for UTS. This uniquely identifies an ASCU on a given interface." ::= { alpsAscuEntry 1 } alpsAscuA1 OBJECT-TYPE SYNTAX AlpsAscuA1A2Value MAX-ACCESS read-create STATUS current DESCRIPTION "A1 value of the ASCU." ::= { alpsAscuEntry 2 } alpsAscuA2 OBJECT-TYPE SYNTAX AlpsAscuA1A2Value MAX-ACCESS read-create STATUS current DESCRIPTION "A2 value of the ASCU." ::= { alpsAscuEntry 3 } alpsAscuCktName OBJECT-TYPE SYNTAX AlpsCktName MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the ALPS Circuit Name for the circuit that is to be used for this ASCU's data. Note that all ASCUs on a physical interface may not use the same ALPS circuit to connect to the central router" ::= { alpsAscuEntry 4 } alpsAscuAlarmsEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies whether alarms (syslog messages or SNMP traps) will be generated for this ASCU." DEFVAL { false } ::= { alpsAscuEntry 5 } alpsAscuRetryOption OBJECT-TYPE SYNTAX INTEGER { resend (1), reenter(2), none(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the retry option for this ASCU. This specifies the error message to be sent to the terminal when a message is dropped at the router. The terminal has three choices - either retransmit the last message (if the terminal can buffer it), re-enter the last message sent or do nothing. Based on the terminal's capabilities, one of these three is configured for the ASCU. Note that this option is the same for all terminals connected to an ASCU because the ALPS feature does not handle individual terminals" DEFVAL { none } ::= { alpsAscuEntry 6 } alpsAscuMaxMsgLength OBJECT-TYPE SYNTAX INTEGER (1..3840) UNITS "bytes" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies Maximum length of Input Message that can be received from this ASCU." DEFVAL { 962 } ::= { alpsAscuEntry 7 } alpsAscuFwdStatusOption OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "If this flag is set, status messages received from the ASCU are forwarded to the host. Otherwise they are discarded. Note that these are relevant only for P1024C (UTS). For ALC, a value of FALSE will be returned." DEFVAL { true } ::= { alpsAscuEntry 8 } alpsAscuState OBJECT-TYPE SYNTAX INTEGER { disabled(1), unknown(2), down(3), up(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Reports the current ASCU Status. ASCUs are initially in disabled state. They are enabled from the parser if the operator wants to. This takes them to an UP state from which they go to a DOWN state if there are too many errors. " ::= { alpsAscuEntry 9 } alpsAscuDownReason OBJECT-TYPE SYNTAX INTEGER { unknown(1), noReason(2), notDown(3), ascuDisabled(4), errorThresholdExceeded(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Reports the Down reason for this ASCU if it is down." DEFVAL { noReason } ::= { alpsAscuEntry 10 } alpsAscuOutPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets transmitted to this ASCU." ::= { alpsAscuEntry 11 } alpsAscuOutOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of octets transmitted to this ASCU." ::= { alpsAscuEntry 12 } alpsAscuInPackets OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets received from this ASCU" ::= { alpsAscuEntry 13 } alpsAscuInOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of octets received from this ASCU." ::= { alpsAscuEntry 14 } alpsAscuDropsGarbledPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets dropped due to the inability to properly decode them. Examples of garbled packets include packets with bad CRCs or bad header information" ::= { alpsAscuEntry 15 } alpsAscuDropsAscuDown OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets dropped because the ASCU had previously been declared DOWN due to error thresholds being exceeded." ::= { alpsAscuEntry 16 } alpsAscuDropsAscuDisabled OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets dropped because the ASCU had previously been declared to be in disabled state." ::= { alpsAscuEntry 17 } alpsAscuEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies whether the ASCU has been enabled or not. After the ASCU has been configured, it must be explicitly enabled to allow it to be polled." DEFVAL { false } ::= { alpsAscuEntry 18 } alpsAscuRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table." ::= { alpsAscuEntry 19 } alpsAscuAutoReset OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies whether a reset command will be automatically issued to any non-responsive ALC ASCUs." DEFVAL { false } ::= { alpsAscuEntry 20 } -- ********************************************************************* -- * ALPS Service Messages -- ********************************************************************* alpsSvcMsgTable OBJECT-TYPE SYNTAX SEQUENCE OF AlpsSvcMsgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of service messages and its associated number. There is a default list of service messages (list 0) as well as user-configurable service messages. On a per-circuit basis, the service message list to use can be selected. The user-configured service message lists are defined in this table. Note that the default service messages are not part of this table." ::= { alpsGlobalObjects 1 } alpsSvcMsgEntry OBJECT-TYPE SYNTAX AlpsSvcMsgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Service Messages configured along with its List number and Service Message Number in that list." INDEX { alpsSvcMsgListNum, alpsSvcMsgNum } ::= { alpsSvcMsgTable 1 } AlpsSvcMsgEntry ::= SEQUENCE { alpsSvcMsgListNum INTEGER, alpsSvcMsgNum INTEGER, alpsSvcMsg DisplayString, alpsSvcMsgRowStatus RowStatus } alpsSvcMsgListNum OBJECT-TYPE SYNTAX INTEGER (1..8) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the Service Msg Number of this Service Msg. A maximum of 8 Service Message lists can be configured not including the one for Default/System (when alpsSvcMsgListNum = 0) Service messages." ::= { alpsSvcMsgEntry 1 } alpsSvcMsgNum OBJECT-TYPE SYNTAX INTEGER (1..8) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the Service Msg Number of this Service Msg. A Maximum of 8 messages can be present." ::= { alpsSvcMsgEntry 2 } alpsSvcMsg OBJECT-TYPE SYNTAX DisplayString (SIZE (1..50)) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the Service Message string ." ::= { alpsSvcMsgEntry 3 } alpsSvcMsgRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table." ::= { alpsSvcMsgEntry 4 } -- ********************************************************************* -- * ALPS X.121 to Ip Translation Object - Admin Object -- ********************************************************************* alpsX121ToIpTransTable OBJECT-TYPE SYNTAX SEQUENCE OF AlpsX121ToIpTransEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A Translation table between X.121 address and IP address. This is intended to allow a connection to be established to the appropriate remote router. The X121 address in the call packet is used to look up the IP address of the remote peer" ::= { alpsGlobalObjects 2 } alpsX121ToIpTransEntry OBJECT-TYPE SYNTAX AlpsX121ToIpTransEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A mapping table between X.121 address and IP address." INDEX { ifIndex, alpsX121 } ::= { alpsX121ToIpTransTable 1 } AlpsX121ToIpTransEntry ::= SEQUENCE { alpsX121 X121Address, alpsIpAddress IpAddress, alpsX121ToIpTransRowStatus RowStatus } alpsX121 OBJECT-TYPE SYNTAX X121Address MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specfies the X.121 address of the VC established with EMTOX host." ::= { alpsX121ToIpTransEntry 1 } alpsIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "This is the IP address of the remote peer which maps onto the X.121 address." ::= { alpsX121ToIpTransEntry 2 } alpsX121ToIpTransRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table." ::= { alpsX121ToIpTransEntry 3 } -- ********************************************************************* -- * ALPS Notifications at Remote router -- ********************************************************************* ciscoAlpsMIBNotificationPrefix OBJECT IDENTIFIER ::= { ciscoAlpsMIB 2 } ciscoAlpsMIBNotifications OBJECT IDENTIFIER ::= { ciscoAlpsMIBNotificationPrefix 0 } alpsPeerStatusChange NOTIFICATION-TYPE OBJECTS { alpsRemPeerState } STATUS deprecated DESCRIPTION "This Notification is generated when there is a change in state for the peer connection, provided alarms are enabled for that peer." ::= { ciscoAlpsMIBNotifications 1 } alpsCktStatusChange NOTIFICATION-TYPE OBJECTS { alpsCktBaseState } STATUS current DESCRIPTION "This Notification has to be generated whenever there is a state change for the ALPS circuit, provided alarms are enabled for that circuit" ::= { ciscoAlpsMIBNotifications 2 } alpsAscuStatusChange NOTIFICATION-TYPE OBJECTS { alpsAscuState } STATUS current DESCRIPTION "This Notification has to be generated whenever there is a change in ASCU status, provided alarms are enabled for that ASCU" ::= { ciscoAlpsMIBNotifications 3 } alpsPeerConnStatusChange NOTIFICATION-TYPE OBJECTS { alpsRemPeerConnState } STATUS current DESCRIPTION "This Notification is generated when there is a change in state for an ALPS peer connection, provided alarms are enabled for that peer connection." ::= { ciscoAlpsMIBNotifications 4 } alpsCktOpenFailure NOTIFICATION-TYPE OBJECTS { alpsCktBaseDownReason } STATUS current DESCRIPTION "This Notification is generated whenever there is an open failure for the ALPS circuit, provided alarms are enabled for that circuit" ::= { ciscoAlpsMIBNotifications 5 } alpsCktPartialReject NOTIFICATION-TYPE OBJECTS { alpsCktAscuIfIndex, alpsCktAscuId } STATUS current DESCRIPTION "This Notification is generated whenever there is an open confirmation that contains a list of rejected ASCUs for the ALPS circuit, provided alarms are enabled for that circuit" ::= { ciscoAlpsMIBNotifications 6 } -- ************************************************************************* -- * Conformance Information -- ************************************************************************* -- alpsMibConformance OBJECT IDENTIFIER ::= { ciscoAlpsMIB 3 } alpsMibCompliances OBJECT IDENTIFIER ::= { alpsMibConformance 1 } alpsMibGroups OBJECT IDENTIFIER ::= { alpsMibConformance 2 } alpsMibCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for ALPS." MODULE -- this module MANDATORY-GROUPS { alpsPeerGroup, alpsCktGroup, alpsIfP1024Group, alpsIfHostlinkGroup, alpsAscuGroup, alpsSvcMsgGroup, alpsAddrTransGroup -- alpsNotificationGroup } ::= { alpsMibCompliances 1 } alpsMibComplianceRev1 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for ALPS." MODULE -- this module MANDATORY-GROUPS { alpsCktGroup, alpsIfP1024Group, alpsIfHostlinkGroup, alpsAscuGroup, alpsSvcMsgGroup, alpsAddrTransGroup, alpsPeerGroupRev1 -- alpsNotificationGroupRev1 } ::= { alpsMibCompliances 2 } alpsMibComplianceRev2 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for ALPS." MODULE -- this module MANDATORY-GROUPS { alpsCktGroup, alpsIfP1024GroupRev1, alpsIfHostlinkGroup, alpsAscuGroupRev1, alpsSvcMsgGroup, alpsAddrTransGroup, alpsPeerGroupRev1 -- alpsNotificationGroupRev2 } ::= { alpsMibCompliances 3 } alpsPeerGroup OBJECT-GROUP OBJECTS { alpsPeerLocalIpAddr, alpsPeerLocalAtpPort, alpsPeerKeepaliveTimeout, alpsPeerKeepaliveMaxRetries, alpsPeerInCallsAcceptFlag, alpsRemPeerConnType, alpsRemPeerLocalPort, alpsRemPeerRemotePort, alpsRemPeerState, alpsRemPeerUptime, alpsRemPeerNumActiveCkts, alpsRemPeerIdleTimer, alpsRemPeerAlarmsEnabled, alpsRemPeerTCPQlen, alpsRemPeerOutPackets, alpsRemPeerOutOctets, alpsRemPeerInPackets, alpsRemPeerInOctets, alpsRemPeerDropsGiant, alpsRemPeerDropsQFull, alpsRemPeerDropsPeerUnreach, alpsRemPeerRowStatus } STATUS deprecated DESCRIPTION "A collection of objects providing Peer information" ::= { alpsMibGroups 1 } alpsCktGroup OBJECT-GROUP OBJECTS { alpsCktBasePriPeerAddr, alpsCktBaseAlarmsEnabled, alpsCktBaseConnType, alpsCktBaseState, alpsCktBaseNumActiveAscus, alpsCktBaseCurrentPeer, alpsCktBaseLifeTimeTimer, alpsCktBaseHostLinkNumber, alpsCktBaseHostLinkType, alpsCktBaseRemHld, alpsCktBaseLocalHld, alpsCktBaseDownReason, alpsCktBaseOutPackets, alpsCktBaseOutOctets, alpsCktBaseInPackets, alpsCktBaseInOctets, alpsCktBaseDropsCktDisabled, alpsCktBaseDropsQOverflow, alpsCktBaseDropsLifeTimeExpd, alpsCktBaseEnabled, alpsCktBaseRowStatus, alpsCktX25IfIndex, alpsCktX25LCN, alpsCktX25HostX121, alpsCktX25RemoteX121, alpsCktX25DropsVcReset, alpsCktP1024BackupPeerAddr, alpsCktP1024RetryTimer, alpsCktP1024IdleTimer, alpsCktP1024EmtoxX121, alpsCktP1024Ax25LCN, alpsCktP1024WinOut, alpsCktP1024WinIn, alpsCktP1024OutPktSize, alpsCktP1024InPktSize, alpsCktP1024SvcMsgList, alpsCktP1024SvcMsgIntvl, alpsCktP1024DropsUnkAscu, alpsCktP1024RowStatus, alpsCktAscuIfIndex, alpsCktAscuId, alpsCktAscuStatus, alpsCktBaseCurrPeerConnId, alpsCktP1024MatipCloseDelay } STATUS current DESCRIPTION "A collection of objects providing Circuit information" ::= { alpsMibGroups 2 } alpsIfP1024Group OBJECT-GROUP OBJECTS { alpsIfP1024EncapType, alpsIfP1024PollRespTimeout, alpsIfP1024GATimeout, alpsIfP1024PollPauseTimeout, alpsIfP1024MaxErrCnt, alpsIfP1024MaxRetrans, alpsIfP1024CurrErrCnt, alpsIfP1024MinGoodPollResp, alpsIfP1024PollingRatio, alpsIfP1024NumAscus } STATUS deprecated DESCRIPTION "A collection of objects providing ALC interface information" ::= { alpsMibGroups 3 } alpsIfHostlinkGroup OBJECT-GROUP OBJECTS { alpsIfHLinkX25ProtocolType, alpsIfHLinkAx25PvcDamp, alpsIfHLinkEmtoxHostX121, alpsIfHLinkActiveCkts } STATUS current DESCRIPTION "A collection of objects providing Hostlink information" ::= { alpsMibGroups 4 } alpsAscuGroup OBJECT-GROUP OBJECTS { alpsAscuA1, alpsAscuA2, alpsAscuCktName, alpsAscuAlarmsEnabled, alpsAscuRetryOption, alpsAscuMaxMsgLength, alpsAscuFwdStatusOption, alpsAscuState, alpsAscuDownReason, alpsAscuOutPackets, alpsAscuOutOctets, alpsAscuInPackets, alpsAscuInOctets, alpsAscuDropsGarbledPkts, alpsAscuDropsAscuDown, alpsAscuDropsAscuDisabled, alpsAscuEnabled, alpsAscuRowStatus } STATUS deprecated DESCRIPTION "A collection of objects providing ASCU information" ::= { alpsMibGroups 5 } alpsSvcMsgGroup OBJECT-GROUP OBJECTS { alpsSvcMsg, alpsSvcMsgRowStatus } STATUS current DESCRIPTION "A collection of objects providing Service Message information" ::= { alpsMibGroups 6 } alpsAddrTransGroup OBJECT-GROUP OBJECTS { alpsIpAddress, alpsX121ToIpTransRowStatus } STATUS current DESCRIPTION "A collection of objects providing Address Translation information." ::= { alpsMibGroups 7 } alpsPeerGroupRev1 OBJECT-GROUP OBJECTS { alpsPeerLocalIpAddr, alpsPeerLocalAtpPort, alpsPeerKeepaliveTimeout, alpsPeerKeepaliveMaxRetries, alpsPeerInCallsAcceptFlag, alpsRemPeerCfgActivation, alpsRemPeerCfgTCPQLen, alpsRemPeerCfgIdleTimer, alpsRemPeerCfgNoCircTimer, alpsRemPeerCfgAlarmsOn, alpsRemPeerCfgStatIntvl, alpsRemPeerCfgStatRetry, alpsRemPeerCfgRowStatus, alpsRemPeerConnLocalPort, alpsRemPeerConnForeignPort, alpsRemPeerConnState, alpsRemPeerConnProtocol, alpsRemPeerConnCreation, alpsRemPeerConnActivation, alpsRemPeerConnUptime, alpsRemPeerConnNumActCirc, alpsRemPeerConnLastTxRx, alpsRemPeerConnLastRxAny, alpsRemPeerConnIdleTimer, alpsRemPeerConnNoCircTimer, alpsRemPeerConnTCPQLen, alpsRemPeerConnAlarmsOn, alpsRemPeerConnStatIntvl, alpsRemPeerConnStatRetry, alpsRemPeerConnDownReason, alpsRemPeerConnOutPackets, alpsRemPeerConnOutOctets, alpsRemPeerConnInPackets, alpsRemPeerConnInOctets, alpsRemPeerConnDropsGiant, alpsRemPeerConnDropsQFull, alpsRemPeerConnDropsUnreach, alpsRemPeerConnDropsVersion } STATUS current DESCRIPTION "A collection of objects providing peer information." ::= { alpsMibGroups 9 } alpsIfP1024GroupRev1 OBJECT-GROUP OBJECTS { alpsIfP1024EncapType, alpsIfP1024PollRespTimeout, alpsIfP1024GATimeout, alpsIfP1024PollPauseTimeout, alpsIfP1024MaxErrCnt, alpsIfP1024MaxRetrans, alpsIfP1024CurrErrCnt, alpsIfP1024MinGoodPollResp, alpsIfP1024PollingRatio, alpsIfP1024NumAscus, alpsIfP1024ServMsgFormat, alpsIfP1024ServMsgStatusChange, alpsIfP1024ServMsgDropTermAddr } STATUS current DESCRIPTION "A collection of objects providing ALC interface information" ::= { alpsMibGroups 11 } alpsAscuGroupRev1 OBJECT-GROUP OBJECTS { alpsAscuA1, alpsAscuA2, alpsAscuCktName, alpsAscuAlarmsEnabled, alpsAscuRetryOption, alpsAscuMaxMsgLength, alpsAscuFwdStatusOption, alpsAscuState, alpsAscuDownReason, alpsAscuOutPackets, alpsAscuOutOctets, alpsAscuInPackets, alpsAscuInOctets, alpsAscuDropsGarbledPkts, alpsAscuDropsAscuDown, alpsAscuDropsAscuDisabled, alpsAscuEnabled, alpsAscuRowStatus, alpsAscuAutoReset } STATUS current DESCRIPTION "A collection of objects providing ASCU information" ::= { alpsMibGroups 12 } --alpsNotificationGroup NOTIFICATION-GROUP -- NOTIFICATIONS { -- alpsPeerStatusChange, -- alpsCktStatusChange, -- alpsAscuStatusChange -- } -- STATUS obsolete -- DESCRIPTION -- "A collection of notifications. " -- ::= { alpsMibGroups 8 } --alpsNotificationGroupRev1 NOTIFICATION-GROUP -- NOTIFICATIONS { -- alpsCktStatusChange, -- alpsAscuStatusChange, -- alpsPeerConnStatusChange -- } -- STATUS deprecated -- DESCRIPTION -- "A collection of notifications. " -- ::= { alpsMibGroups 10 } --alpsNotificationGroupRev2 NOTIFICATION-GROUP -- NOTIFICATIONS { -- alpsCktStatusChange, -- alpsAscuStatusChange, -- alpsPeerConnStatusChange, -- alpsCktOpenFailure, -- alpsCktPartialReject -- } -- STATUS current -- DESCRIPTION -- "A collection of notifications. " -- ::= { alpsMibGroups 13 } END