CISCO-ATM-CONN-INFO-MIB -- ***************************************************************** -- CISCO-ATM-CONN-INFO-MIB -- -- April 2003, Rashmi Purandare -- -- Copyright (c) 2003 by cisco Systems, Inc. -- All rights reserved. -- ***************************************************************** CISCO-ATM-CONN-INFO-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Gauge32, Unsigned32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF ifIndex FROM IF-MIB ciscoMgmt FROM CISCO-SMI TEXTUAL-CONVENTION FROM SNMPv2-TC; ciscoAtmConnInfoMIB MODULE-IDENTITY LAST-UPDATED "200306160000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-wanatm@cisco.com" DESCRIPTION "The MIB module for providing the parameters configured on an ATM interface. Terminologies used: SVC : Switched Virtual Channel SPVC : Soft Permanent Virtual Circuit SPVP : Soft Permanent Virtual Path SVPC : Switched Virtual Path Connection DAX : Connection with endpoints on the same ATM switch P2p : Point-to-point connection P2mp : Point-to-multi-point connection Root : The root of point-to-multipoint connection, which is associated with a VPI/VCI Leaf : Usually one point-to-multipoint connection consists of one root and one or more leaves. Leaf is the branch point for point to multipoint connection that is associated with a VPI/VCI Party: One or more party is associated with each leaf, all parties are associated with the same VPI/VCI that its leaf belongs to Source Via Node Destination ------- ------- ------- A| |B C| |D E| |F --+-----+----------+-----+------------+-----+-- | | | | | | ------- ------- ------- Each active connection has two terminating endpoints. In the above diagram, Endpoints A and F are terminating. Of these the master endpoint of the connection initiates the routing of the call and is considered the calling party. The slave endpoint is the called party which receives calls and is the destination of a call. Any endpoints that are created either on Via nodes or on the node with the terminating endpoint in order to have a complete connections between endpoints A and F are said to be intermediate endpoints. In the above diagram, endpoints B, C, D and E are intermediate endpoints. " REVISION "200306160000Z" DESCRIPTION "Initial version of the MIB." ::= { ciscoMgmt 9999 } caciMIBNotifications OBJECT IDENTIFIER ::= { ciscoAtmConnInfoMIB 0 } caciMIBObjects OBJECT IDENTIFIER ::= { ciscoAtmConnInfoMIB 1 } -- conn statistics caciAtmConnInfo OBJECT IDENTIFIER ::= { caciMIBObjects 1 } caciIfInfo OBJECT IDENTIFIER ::= { caciAtmConnInfo 1 } caciP2pConns OBJECT IDENTIFIER ::= { caciAtmConnInfo 2 } caciP2pEndpoints OBJECT IDENTIFIER ::= { caciAtmConnInfo 3 } caciP2pIntEndpoints OBJECT IDENTIFIER ::= { caciAtmConnInfo 4 } caciP2mpConns OBJECT IDENTIFIER ::= { caciAtmConnInfo 5 } caciGeneric OBJECT IDENTIFIER ::= { caciAtmConnInfo 6 } -- Textual conventions CaciGeneralConnEPCategory::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "General category for connection or endpoint types supported on the switch. caciP2p : Point to point connection caciP2mpR : Point to multi point root connection caciP2mpL : Point to multi point leaf connection caciP2mpPty: Point to multi point party connection" SYNTAX INTEGER { caciP2p(1), caciP2mpR(2), caciP2mpL(3), caciP2mpPty(4) } CaciP2pConnCategory::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The connection category. caciP2pSvcc : Point to point Svc connection caciP2pSvpc : Point to point Svpc connection caciP2pSpvcD: Point to point Spvc DAX connection caciP2pSpvpD: Point to point Spvp DAX connection caciP2pSpvcR: Point to point SPVC Routed connection caciP2pSpvpR: Point to point Spvp Routed connection" SYNTAX INTEGER { caciP2pSvcc(1), caciP2pSvpc(2), caciP2pSpvcD(3), caciP2pSpvpD(4), caciP2pSpvcR(5), caciP2pSpvpR(6) } CaciP2pEndpointCategory::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The terminating endpoint category. caciP2pSpvcRPEP : Point to point Spvc Routed Persistent endpoint caciP2pSpvcRNPEP: Point to point Spvc Routed Non-persistent endpoint caciP2pSpvpRPEP : Point to point Spvp Routed Persistent endpoint caciP2pSpvpRNPEP: Point to point Spvp Routed Non-persistent endpoint caciP2pSpvcDEP : Point to point Spvc DAX endpoint caciP2pSpvpDEP : Point to point Spvp DAX endpoint" SYNTAX INTEGER { caciP2pSpvcRPEP(1), caciP2pSpvcRNPEP(2), caciP2pSpvpRPEP(3), caciP2pSpvpRNPEP(4), caciP2pSpvcDEP(5), caciP2pSpvpDEP(6) } CaciP2pIntEndpointCategory::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The intermediate endpoint category. caciP2pSvccIntEP : Point to point Svc intermediate endpoint caciP2pSvpcIntEP : Point to point Svpc intermediate endpoint caciP2pSpvcRIntEP: Point to point Spvc Routed intermediate endpoint caciP2pSpvpRIntEP: Point to point Spvp Routed intermediate endpoint" SYNTAX INTEGER { caciP2pSvccIntEP(1), caciP2pSvpcIntEP(2), caciP2pSpvcRIntEP(3), caciP2pSpvpRIntEP(4) } CaciP2mpConnCategory::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The point to multipoint connection category. caciP2mpSvcRoot : Point to multipoint Svc root connection caciP2mpSvcLeaf : Point to multipoint Svc leaf connection caciP2mpSvcParty : Point to multipoint Svc party connection caciP2mpSvpcRoot : Point to multipoint Svpc root connection caciP2mpSvpcLeaf : Point to multipoint Svpc leaf connection caciP2mpSvpcParty: Point to multipoint Svpc party connection caciP2mpSpvcP : Point to multipoint Spvc persistent connection caciP2mpSpvcNP : Point to multipoint Spvc non-persistent connection caciP2mpSpvcAct : Point to multipoint Spvc Active connection caciP2mpSpvpP : Point to multipoint Spvp persistent connection caciP2mpSpvpNP : Point to multipoint Spvp non-persistent connection caciP2mpSpvpAct : Point to multipoint Spvp active connection caciP2mpSpvcPaP : Point to multipoint Spvc party persistent connection caciP2mpSpvcPaAct: Point to multipoint Spvc party active connection caciP2mpSpvpPaP : Point to multipoint Spvp party persistent connection caciP2mpSpvpPaAct: Point to multipoint Spvp party active connection" SYNTAX INTEGER { caciP2mpSvcRoot(1), caciP2mpSvcLeaf(2), caciP2mpSvcParty(3), caciP2mpSvpcRoot(4), caciP2mpSvpcLeaf(5), caciP2mpSvpcParty(6), caciP2mpSpvcP(7), caciP2mpSpvcNP(8), caciP2mpSpvcAct(9), caciP2mpSpvpP(10), caciP2mpSpvpNP(11), caciP2mpSpvpAct(12), caciP2mpSpvcPaP(13), caciP2mpSpvcPaAct(14), caciP2mpSpvpPaP(15), caciP2mpSpvpPaAct(16) } CaciATMEndpointCategory::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The connection category. caciTotalSpvc : Total SPVC endpoints configured on the ATM switch caciP2pTotalInt : Total intermediate endpoints configured on the ATM switch caciTotalMaster : Total master endpoints configured on the ATM switch caciTotalSlave : Total slave endpoints configured on the ATM switch" SYNTAX INTEGER { caciTotalSpvc(1), caciP2pTotalInt(2), caciTotalMaster(3), caciTotalSlave(4) } -- Node related scalars -- Total connections caciP2pTotalConfConns OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the total point to point connections that are configured on this ATM switch." ::= { caciGeneric 1 } caciP2pMaxPossibleConns OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the upper limit of the point to point and point to multipoint connections that are allowed to be configured on this ATM switch." ::= { caciGeneric 2 } --Total endpoints caciMaxPossibleEndpoints OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the upper limit of all the possible endpoints that are allowed to be configured on this ATM switch." ::= { caciGeneric 3 } -- Summary of switch endpoints caciGenericEndpointTable OBJECT-TYPE SYNTAX SEQUENCE OF CaciGenericEndpointEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table contains number of connection per CaciATMEndpointCategory." ::= { caciGeneric 4 } caciGenericEndpointEntry OBJECT-TYPE SYNTAX CaciGenericEndpointEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table specifying the number of connections for the corresponding CaciATMEndpointCategory." INDEX { caciATMEndpointCategory } ::= { caciGenericEndpointTable 1 } CaciGenericEndpointEntry ::= SEQUENCE { caciATMEndpointCategory CaciATMEndpointCategory, caciTotalEndpoints Gauge32 } caciATMEndpointCategory OBJECT-TYPE SYNTAX CaciATMEndpointCategory MAX-ACCESS not-accessible STATUS current DESCRIPTION "Endpoint category corresponding to CaciATMEndpointCategory." ::= { caciGenericEndpointEntry 1 } caciTotalEndpoints OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of endpoints of caciATMEndpointCategory configured on this ATM switch." ::= { caciGenericEndpointEntry 2 } -- Interface Connections Statistics table caciConnInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF CaciConnInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Connection Statistics table. This table has the number of connections per interface." ::= { caciIfInfo 1 } caciConnInfoEntry OBJECT-TYPE SYNTAX CaciConnInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the caciConnInfoTable. Each entry in ifTable with ifType values: atm(37), atmLogical(80) or atmVirtual(149) has an associated entry in this table." INDEX { ifIndex, caciGeneralConnEPCategory } ::= { caciConnInfoTable 1 } CaciConnInfoEntry ::= SEQUENCE { caciGeneralConnEPCategory CaciGeneralConnEPCategory, caciNumUsedConns Gauge32 } caciGeneralConnEPCategory OBJECT-TYPE SYNTAX CaciGeneralConnEPCategory MAX-ACCESS not-accessible STATUS current DESCRIPTION "The general connection or endpoint category on this ATM switch." ::= { caciConnInfoEntry 1 } caciNumUsedConns OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the total number of used connections of type caciGeneralConnEPCategory on this interface." ::= { caciConnInfoEntry 2 } -- Summary of total P2p connections caciP2pConnTable OBJECT-TYPE SYNTAX SEQUENCE OF CaciP2pConnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table contains number of connection per CaciP2pConnCategory." ::= { caciP2pConns 1} caciP2pConnEntry OBJECT-TYPE SYNTAX CaciP2pConnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table specifying the number of connections for the corresponding CaciP2pConnCategory." INDEX { caciP2pConnectionCategory } ::= { caciP2pConnTable 1 } CaciP2pConnEntry ::= SEQUENCE { caciP2pConnectionCategory CaciP2pConnCategory, caciP2pTotalConns Gauge32 } caciP2pConnectionCategory OBJECT-TYPE SYNTAX CaciP2pConnCategory MAX-ACCESS not-accessible STATUS current DESCRIPTION "The connection category." ::= { caciP2pConnEntry 1 } caciP2pTotalConns OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of P2p connections of type CaciP2pConnCategory configured on this ATM switch." ::= { caciP2pConnEntry 2 } -- Summary of total P2p Endpoints caciP2pEndpointTable OBJECT-TYPE SYNTAX SEQUENCE OF CaciP2pEndpointEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table contains number of endpoints per CaciP2pEndpointCategory." ::= { caciP2pEndpoints 1} caciP2pEndpointEntry OBJECT-TYPE SYNTAX CaciP2pEndpointEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table specifying the number of endpoints for the corresponding CaciP2pEndpointCategory." INDEX { caciP2pEndptCategory } ::= { caciP2pEndpointTable 1 } CaciP2pEndpointEntry ::= SEQUENCE { caciP2pEndptCategory CaciP2pEndpointCategory, caciP2pTotalConfEndpoints Gauge32 } caciP2pEndptCategory OBJECT-TYPE SYNTAX CaciP2pEndpointCategory MAX-ACCESS not-accessible STATUS current DESCRIPTION "The point to point endpoint category." ::= { caciP2pEndpointEntry 1 } caciP2pTotalConfEndpoints OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of total P2p enpoints of type CaciP2pEndpointCategory configured on this ATM switch." ::= { caciP2pEndpointEntry 2 } -- Summary of Total Active SVC/SPVC P2p intermediate endpoints caciP2pIntEndpointTable OBJECT-TYPE SYNTAX SEQUENCE OF CaciP2pIntEndpointEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table contains number of endpoints per CaciP2pIntEndpointCategory." ::= { caciP2pIntEndpoints 1} caciP2pIntEndpointEntry OBJECT-TYPE SYNTAX CaciP2pIntEndpointEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table specifying the number of endpoints for the corresponding CaciP2pIntEndpointCategory." INDEX { caciP2pIntEndptCategory } ::= { caciP2pIntEndpointTable 1 } CaciP2pIntEndpointEntry ::= SEQUENCE { caciP2pIntEndptCategory CaciP2pIntEndpointCategory, caciP2pTotalIntEndpoints Gauge32 } caciP2pIntEndptCategory OBJECT-TYPE SYNTAX CaciP2pIntEndpointCategory MAX-ACCESS not-accessible STATUS current DESCRIPTION "The point to point intermediate endpoint category." ::= { caciP2pIntEndpointEntry 1 } caciP2pTotalIntEndpoints OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of P2p intermediate enpoints of type CaciP2pIntEndpointCategory present on this ATM switch." ::= { caciP2pIntEndpointEntry 2 } -- Summary of point to multipoint connections caciP2mpConnTable OBJECT-TYPE SYNTAX SEQUENCE OF CaciP2mpConnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table contains number of connection per CaciP2mpConnCategory." ::= { caciP2mpConns 1 } caciP2mpConnEntry OBJECT-TYPE SYNTAX CaciP2mpConnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table specifying the number of connections for the corresponding CaciP2mpConnCategory." INDEX { caciP2mpConnectionCategory } ::= { caciP2mpConnTable 1 } CaciP2mpConnEntry ::= SEQUENCE { caciP2mpConnectionCategory CaciP2mpConnCategory, caciP2mpTotalConfConns Gauge32 } caciP2mpConnectionCategory OBJECT-TYPE SYNTAX CaciP2mpConnCategory MAX-ACCESS not-accessible STATUS current DESCRIPTION "The point to multi point connection category." ::= { caciP2mpConnEntry 1 } caciP2mpTotalConfConns OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of P2mp connections of type CaciP2mpConnCategory configured on this ATM switch." ::= { caciP2mpConnEntry 2 } -- Notifications -- There are no notifications for this module -- conformance information ciscoAtmConnInfoMIBConformance OBJECT IDENTIFIER ::= { ciscoAtmConnInfoMIB 2 } ciscoAtmConnInfoMIBCompliances OBJECT IDENTIFIER ::= { ciscoAtmConnInfoMIBConformance 1 } ciscoAtmConnInfoMIBGroups OBJECT IDENTIFIER ::= { ciscoAtmConnInfoMIBConformance 2 } ciscoAtmConnInfoMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The Compliance statement for ciscoAtm management group." MODULE -- this module MANDATORY-GROUPS { ciscoConnInfoConfMIBGroup, ciscoTotalConnsMIBGroup, ciscoTotalEndpointsMIBGroup } GROUP ciscoP2pConnsMIBGroup DESCRIPTION "Required if P2p connections are supported" GROUP ciscoP2pEndpointsMIBGroup DESCRIPTION "Required if P2p connections are supported" GROUP ciscoP2pIntEndpointsMIBGroup DESCRIPTION "Required if P2p connections are supported" GROUP ciscoP2mpConnsMIBGroup DESCRIPTION "Required if P2mp connections are supported" ::= { ciscoAtmConnInfoMIBCompliances 1 } -- units of conformance ciscoConnInfoConfMIBGroup OBJECT-GROUP OBJECTS { caciNumUsedConns } STATUS current DESCRIPTION "Objects used for representing connection statistical details about an interface." ::= { ciscoAtmConnInfoMIBGroups 1 } ciscoP2pConnsMIBGroup OBJECT-GROUP OBJECTS { caciP2pTotalConns } STATUS current DESCRIPTION "Objects used for representing the point to point connections of a particular CaP2pConnCategory." ::= { ciscoAtmConnInfoMIBGroups 2 } ciscoP2pEndpointsMIBGroup OBJECT-GROUP OBJECTS { caciP2pTotalConfEndpoints } STATUS current DESCRIPTION "Objects used for representing the point to point endpoints of a particular CaP2pEndpointCategory." ::= { ciscoAtmConnInfoMIBGroups 3 } ciscoP2pIntEndpointsMIBGroup OBJECT-GROUP OBJECTS { caciP2pTotalIntEndpoints } STATUS current DESCRIPTION "Objects used for representing the point to point intermediate endpoints of a particular CaP2pIntEndpointCategory." ::= { ciscoAtmConnInfoMIBGroups 4 } ciscoP2mpConnsMIBGroup OBJECT-GROUP OBJECTS { caciP2mpTotalConfConns } STATUS current DESCRIPTION "Objects used for representing the point to multi point connections of a particular CaP2mpConnCategory." ::= { ciscoAtmConnInfoMIBGroups 5 } ciscoTotalConnsMIBGroup OBJECT-GROUP OBJECTS { caciP2pTotalConfConns, caciP2pMaxPossibleConns } STATUS current DESCRIPTION "Objects used for representing the total connections on the ATM switch." ::= { ciscoAtmConnInfoMIBGroups 6 } ciscoTotalEndpointsMIBGroup OBJECT-GROUP OBJECTS { caciMaxPossibleEndpoints, caciTotalEndpoints } STATUS current DESCRIPTION "Objects used for representing the total endpoints on the ATM switch." ::= { ciscoAtmConnInfoMIBGroups 7 } END