CISCO-WAN-ATM-PARTY-MIB -- **************************************************************** -- CISCO-WAN-ATM-PARTY-MIB.my: -- -- CISCO MSSBU ATM Point-to-Multipoint Connection Party MIB -- -- Copyright (c) 2002 by cisco Systems, Inc. -- All rights reserved. -- -- ***************************************************************** CISCO-WAN-ATM-PARTY-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Unsigned32 FROM SNMPv2-SMI RowStatus, TruthValue, DisplayString, TEXTUAL-CONVENTION FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF ifIndex FROM IF-MIB ciscoMgmt FROM CISCO-SMI; ciscoWanAtmPartyMIB MODULE-IDENTITY LAST-UPDATED "200206170000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-wanatm@cisco.com " DESCRIPTION "A management station can use this MIB to provision, manage or delete one or more 'parties' on an ATM point-to-multipoint Soft PVCC(SPVC) connection. The user must add a root endpoint to the managed system before proceed to add one or more 'parties' to the root. The provision and management of a 'root' endpoint is beyond the scope of this MIB. Please refer to CISCO-WAN-ATM-CONN-MIB.my for the provisioning and management of a 'root' endpoint. This MIB is based on 'ITU-T recommendation Q.2971 (10/95) BROADBAND INTEGRATED SERVICES DIGITAL NETWORK (B-ISDN) - DIGITAL SUBSCRIBER SIGNALLING SYSTEM No. 2 (DSS 2) - USER-NETWORK INTERFACE LAYER 3 SPECIFICATION FOR POINT- TO-MULTIPOINT CALL/CONNECTION CONTROL" REVISION "200206170000Z" DESCRIPTION "Initial version of the MIB" ::= { ciscoMgmt 99998 } ciscoWanAtmPartyMIBNotifs OBJECT IDENTIFIER ::= { ciscoWanAtmPartyMIB 0 } ciscoWanAtmPartyMIBObjects OBJECT IDENTIFIER ::= { ciscoWanAtmPartyMIB 1 } cwapConfig OBJECT IDENTIFIER ::= { ciscoWanAtmPartyMIBObjects 1 } ciscoWanAtmPartyMIBConform OBJECT IDENTIFIER ::= { ciscoWanAtmPartyMIB 2 } -- TEXTUAL CONVENTIONS WanPartyAdminStatus ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Defines 'administrative status' of a 'party'." SYNTAX INTEGER { up(1), down(2) } WanPartyOperStatus ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Defines 'operational status' of a 'party'." SYNTAX INTEGER { ok(1), fail(2) } WanNsapAtmAddress ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "ATM address used by the managed system. The only address type presently supported is ATM Network Service Access Point (NSAP) addresses (20 octets)." SYNTAX OCTET STRING (SIZE(20)) -- Party Configuration Group cwapConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF CwapConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains mandatory 'party' configuration for all ATM point-to-multipoint Soft Permanent Virtual Channel Connections (SPVC). " ::= { cwapConfig 1 } cwapConfigEntry OBJECT-TYPE SYNTAX CwapConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the 'cwapConfigTable'. Each entry corresponds to one party of a point-to-multipoint connection. (1) To add an entry, the management application must first provision a 'root' endpoint. (2) While adding an entry, the variables 'cwapNSAPAddress', 'cwapVpi' and 'cwapVci' are mandatory. The 'cwapNSAPAddress', 'csapVpi' and 'cwapVci' are not required to be unique. (3) The row creation will fail if the root endpoint does not exist. (4) The following management operations are permitted on a row when the 'cwapRowStatus' is 'active': a) row deletion. b) toggling of the administrative status of a 'party' via the 'cwapAdminStatus' object. c) triggering a reroute via the 'cwapReroute' object. (5) The table index 'ifIndex' refers to that of the root. The 'ifIndex' identifies an ATM Virtual Interface ('ifType' atmVirtual(149)). " INDEX {ifIndex, cwapRootVpi, cwapRootVci, cwapReference} ::= { cwapConfigTable 1 } CwapConfigEntry ::= SEQUENCE { cwapRootVpi Integer32, cwapRootVci Integer32, cwapReference Integer32, cwapNSAPAddress WanNsapAtmAddress, cwapVpi Integer32, cwapVci Integer32, cwapAdminStatus WanPartyAdminStatus, cwapOperStatus WanPartyOperStatus, cwapReroute TruthValue, cwapIdentifier Unsigned32, cwapUploadCounter Unsigned32, cwapRootPhysicalId DisplayString, cwapRowStatus RowStatus } cwapRootVpi OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies the Virtual Path Identifier(VPI) of the root endpoint this party is associated with." ::= { cwapConfigEntry 1 } cwapRootVci OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies the Virtual Channel Identifier (VCI) of the root endpoint this party is associated with." ::= { cwapConfigEntry 2 } cwapReference OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer which serves to distinguish between the multiple parties attached to a root of a point-to-multipoint SPVC." ::= { cwapConfigEntry 3 } cwapNSAPAddress OBJECT-TYPE SYNTAX WanNsapAtmAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The ATM NSAP address of this party." ::= { cwapConfigEntry 4 } cwapVpi OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-create STATUS current DESCRIPTION "The VPI value of this party." ::= { cwapConfigEntry 5 } cwapVci OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The VCI value of this party." ::= { cwapConfigEntry 6 } cwapReroute OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "The management station uses this object to trigger the re-routing of the party. * Rerouting takes effect, when this object is set to true(1). When set to false(2), no action is taken. * The value 'false' will always be returned on snmp query to this variable. * During reroute operation, the 'cwapOperStatus' will contain the value 'fail'. Upon successful completion of reroute, the 'cwapOperStatus' will change to the value 'ok'. If the reroute operation failed, the 'cwapOperStatus' will stay in 'fail'. The management station should query the 'cwapOperStatus' to decide if a reroute request is successful or not." DEFVAL { false } ::= { cwapConfigEntry 7 } cwapAdminStatus OBJECT-TYPE SYNTAX WanPartyAdminStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The 'administrative status' of this party. " DEFVAL { up } ::= { cwapConfigEntry 8 } cwapOperStatus OBJECT-TYPE SYNTAX WanPartyOperStatus MAX-ACCESS read-only STATUS current DESCRIPTION "The 'operational status' of this party." ::= { cwapConfigEntry 9 } cwapIdentifier OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "An arbitrary integer which serves to distinguish all parties on a node. This value is assigned by the managed system when a party is added. The use of this variable is implementation specific." ::= { cwapConfigEntry 10 } cwapUploadCounter OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "This counter is used by the management station to determine if a party had been modified and requires further action from management station. The use of this variable is implementation specific. This functionality is conventionally achieved by time stamping using a time-of-day clock. However, in switches where time-of-day clock is not available, the following scheme is used: The upload counter is incremented, when: * assignment of a party to a cwapIdentifier. This happens when a party is added and assigned this cwapIdentifier. * de-assignment of connection from a cwapIdentifier. This happens when a connection is deleted. * When there is a status change done to this party." ::= { cwapConfigEntry 11 } cwapRootPhysicalId OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains physical description of the physical interface the root resides. The presentation of this object is implementation specific." ::= { cwapConfigEntry 12 } cwapRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create, modify or delete an entry in the ciscoWanAtmPartyTable. * A row may be created using the 'CreateAndGo' option. When the row is successfully created, the RowStatus would be set to 'active' by the agent. * A row may be deleted by setting the RowStatus to 'destroy'. " ::= { cwapConfigEntry 13 } ciscoWanAtmPartyMIBCompliances OBJECT IDENTIFIER ::= { ciscoWanAtmPartyMIBConform 1 } ciscoWanAtmPartyMIBGroups OBJECT IDENTIFIER ::= { ciscoWanAtmPartyMIBConform 2 } -- compliance statements ciscoWanAtmPartyMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMPv2 entities which implement one or more parties of an ATM point-to- multi-point connection." MODULE -- this module MANDATORY-GROUPS { ciscoWanAtmPartyGroup } OBJECT cwapRowStatus SYNTAX INTEGER { active(1), createAndGo(4), destroy(6) }-- subset of RowStatus DESCRIPTION "Only three of the six enumerated values for the RowStatus textual convention need to be supported." ::= { ciscoWanAtmPartyMIBCompliances 1 } -- units of conformance ciscoWanAtmPartyGroup OBJECT-GROUP OBJECTS { cwapNSAPAddress, cwapVpi, cwapVci, cwapAdminStatus, cwapOperStatus, cwapReroute, cwapIdentifier, cwapUploadCounter, cwapRootPhysicalId, cwapRowStatus } STATUS current DESCRIPTION "This group contains the information of a 'party' per each SPVC point-to-multipoint connection." ::= { ciscoWanAtmPartyMIBGroups 2 } END