CTRON-AppleTalk-ROUTER-MIB CTRON-AppleTalk-ROUTER-MIB DEFINITIONS ::= BEGIN -- ctron-appletalk-router-mib.txt -- Revision: 1.01.00 -- Part Number: -- Date: August 11, 1995 -- Cabletron Systems, Inc. -- 35 Industrial Way, P.O. Box 5005 -- Rochester, NH 03867-0505 -- (603) 332-9400 -- support@ctron.com -- This module provides authoritative definitions for Cabletron's -- enterprise specific at Routing Services MIB. -- -- This module will be extended, as required. -- -- Cabletron Systems reserves the right to make changes in -- specification and other information contained in this document -- without prior notice. The reader should consult Cabletron Systems -- to determine whether any such changes have been made. -- -- In no event shall Cabletron Systems be liable for any incidental, -- indirect, special, or consequential damages whatsoever (including -- but not limited to lost profits) arising out of or related to this -- document or the information contained in it, even if Cabletron -- Systems has been advised of, known, or should have known, the -- possibility of such damages. -- -- Cabletron grants vendors, end-users, and other interested parties -- a non-exclusive license to use this Specification in connection -- with the management of Cabletron products. -- Copyright August 95 Cabletron Systems -- IMPORTS OBJECT-TYPE FROM RFC-1212 DisplayString, PhysAddress FROM RFC1213-MIB nwRouter, nwRtrProtoSuites FROM ROUTER-OIDS Counter, TimeTicks, Gauge FROM RFC1155-SMI; nwRtrExperimental OBJECT IDENTIFIER ::= { nwRouter 4 } -- The At Router Group. nwAtRouter OBJECT IDENTIFIER ::= { nwRtrProtoSuites 4 } nwAtMibs OBJECT IDENTIFIER ::= { nwAtRouter 1 } nwAtComponents OBJECT IDENTIFIER ::= { nwAtRouter 2 } -- At Router Component Groups nwAtSystem OBJECT IDENTIFIER ::= { nwAtComponents 1 } nwAtForwarding OBJECT IDENTIFIER ::= { nwAtComponents 2 } nwAtTopology OBJECT IDENTIFIER ::= { nwAtComponents 4 } nwAtFib OBJECT IDENTIFIER ::= { nwAtComponents 5 } nwAtEndSystems OBJECT IDENTIFIER ::= { nwAtComponents 6 } nwAtAccessControl OBJECT IDENTIFIER ::= { nwAtComponents 7 } nwAtFilters OBJECT IDENTIFIER ::= { nwAtComponents 8 } nwAtRedirector OBJECT IDENTIFIER ::= { nwAtComponents 9 } nwAtEvent OBJECT IDENTIFIER ::= { nwAtComponents 10 } nwAtWorkGroup OBJECT IDENTIFIER ::= { nwAtComponents 11 } nwAtNetDiag OBJECT IDENTIFIER ::= { nwAtComponents 12 } -- At Router System Groups nwAtSysConfig OBJECT IDENTIFIER ::= { nwAtSystem 1 } nwAtSysAdministration OBJECT IDENTIFIER ::= { nwAtSystem 2 } -- At Router Forwarding Groups nwAtFwdSystem OBJECT IDENTIFIER ::= { nwAtForwarding 1 } nwAtFwdInterfaces OBJECT IDENTIFIER ::= { nwAtForwarding 2 } nwAtFwdCounters OBJECT IDENTIFIER ::= { nwAtFwdSystem 1 } nwAtFwdIfConfig OBJECT IDENTIFIER ::= { nwAtFwdInterfaces 1 } nwAtFwdIfCounters OBJECT IDENTIFIER ::= { nwAtFwdInterfaces 2 } -- At Router Routing Groups nwAtDistanceVector OBJECT IDENTIFIER ::= { nwAtTopology 1 } nwAtLinkState OBJECT IDENTIFIER ::= { nwAtTopology 2 } nwAtProto OBJECT IDENTIFIER ::= { nwAtDistanceVector 1 } nwAtProtoSystem OBJECT IDENTIFIER ::= { nwAtProto 1 } nwAtProtoInterface OBJECT IDENTIFIER ::= { nwAtProto 2 } nwAtProtoConfig OBJECT IDENTIFIER ::= { nwAtProtoSystem 1 } nwAtProtoCounters OBJECT IDENTIFIER ::= { nwAtProtoSystem 2 } nwAtProtoIfConfig OBJECT IDENTIFIER ::= { nwAtProtoInterface 1 } nwAtProtoIfCounters OBJECT IDENTIFIER ::= { nwAtProtoInterface 2 } -- At Router Host End Systems Groups nwAtHostsSystem OBJECT IDENTIFIER ::= { nwAtEndSystems 1 } nwAtHostsInterfaces OBJECT IDENTIFIER ::= { nwAtEndSystems 2 } nwAtHostsToMedia OBJECT IDENTIFIER ::= { nwAtEndSystems 3 } -- At Router Access Control Group -- At Router Filters Group -- At Router Redirector Group -- At Router Event Log Group nwAtEventLogConfig OBJECT IDENTIFIER ::= { nwAtEvent 1 } nwAtEventLogFilterTable OBJECT IDENTIFIER ::= { nwAtEvent 2 } nwAtEventLogTable OBJECT IDENTIFIER ::= { nwAtEvent 3 } -- At Router Work-Group Group -- AT Network Diagnostic Group nwAtNetDiagPing OBJECT IDENTIFIER ::= { nwAtNetDiag 1 } nwAtNetDiagTelnet OBJECT IDENTIFIER ::= { nwAtNetDiag 2 } nwAtNetDiagOutbound OBJECT IDENTIFIER ::= { nwAtNetDiag 3 } AtNetworkNumber ::= -- 2 octets of network number in network byte order OCTET STRING (SIZE (2)) AtDdpNodeAddress ::= -- 2 octets of net number in network byte order, -- 1 octet of node number OCTET STRING (SIZE (3)) AtName ::= -- 0 to 32 octets of -- AppleTalk ASCII [10] OCTET STRING (SIZE (0..32)) -- At MIB Group -- This group contains information about the revision level of this -- MIB within the device. It allows verification of the released -- version without having to read other objects. nwAtMibRevText OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the current revision level of the Cabletron at Routing Services MIB in textual format." ::= { nwAtMibs 1 } -- At Router System Group -- This group contains the objects that pertain to the at routing -- services at a global, device-wide level. -- At System Configuration Group -- This group contains the objects that pertain to the setup and -- configuration of the At routing services at a global, -- device-wide level. nwAtSysRouterId OBJECT-TYPE SYNTAX AtNetworkNumber ACCESS read-write STATUS mandatory DESCRIPTION "The AppleTalk node address used to uniquely identify the host (device) running the AppleTalk Routing Services. The value of nwAtSysRouterId is equal to the highest AppleTalk node address assigned to any router port." ::= { nwAtSysConfig 1 } -- At System Administration Group -- This group contains the objects that pertain to the administration of -- At routing services at a global, device-wide level. nwAtSysAdminSTATUS OBJECT-TYPE SYNTAX INTEGER { other(1), -- none of the following disabled(2), -- shutdown the router enabled(3) -- startup the router } ACCESS read-write STATUS mandatory DESCRIPTION "Sets the administrative state of AppleTalk Routing Services system wide. Enabled (3) causes AppleTalk Routing Services to become active on all router ports configured and enabled for AppleTalk Routing Services. Disabled (2) causes AppleTalk Routing Services to become inactive system-wide." ::= { nwAtSysAdministration 1 } nwAtSysOperSTATUS OBJECT-TYPE SYNTAX INTEGER { other(1), -- none of the following disabled(2), -- not running enabled(3), -- running pending-disable(4), -- shut-down in progress pending-enable(5), -- start-up in progress invalid-config(6) -- not running,invalid config } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the operating condition of AppleTalk Routing Services system- wide. The value of nwAtSysOperStatus indicates any problem with your AppleTalk Routing Services configuration. A value of 6 indicates that regardless of the value of nwAtSysAdminStatus, AppleTalk Routing Services is not operating because of an invalid configuration." ::= { nwAtSysAdministration 2 } nwAtSysAdminReset OBJECT-TYPE SYNTAX INTEGER { other(1), -- none of the following reset(2) -- force a reset } ACCESS read-write STATUS mandatory DESCRIPTION "Resets AppleTalk Routing Services system-wide. Reset (2) forces a restart of AppleTalk Routing Services without a graceful shutdown on any active router ports and without affecting any other routing services." ::= { nwAtSysAdministration 3 } nwAtSysOperationalTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the elapsed time, in hundredths of a second, that nwAtSysOperStatus has been in its current state." ::= { nwAtSysAdministration 4 } nwAtSysVersion OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the current revision level of the AppleTalk Routing Services firmware, in textual format." ::= { nwAtSysAdministration 5 } -- at Forwarding Group -- This group contains the managed objects used to setup and configure -- the at router ports for packet forwarding as well as the aggregate -- and per-interface at packet forwarding counters. -- at System-wide Packet Forwarding Counters -- This group contains the aggregate (device-wide) at packet forwarding -- counters. The byte counters include bytes for the network layer on -- up, framing is not included. nwAtFwdCtrAdminSTATUS OBJECT-TYPE SYNTAX INTEGER { other(1), disabled(2), enabled(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Sets the administrative state of the aggregate (system-wide) AppleTalk packet and byte counters. Enabled (3) causes these counters to become active. Disabled (2) causes these counters to become inactive." ::= { nwAtFwdCounters 1 } nwAtFwdCtrReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Reset(2) resets the aggregate (system-wide) AppleTalk packet and byte counters. Reset (2) resets the AppleTalk aggregate counters to 0.nwAtFwdCtrOperationalTime is also reset to 0." ::= { nwAtFwdCounters 2 } nwAtFwdCtrOperationalTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the elapsed time, in hundredths of a second, that nwAtFwdCtrAdminStatus has been in the current state." ::= { nwAtFwdCounters 3 } nwAtFwdCtrInPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk packets that have been received, system-wide, during nwAtFwdCtrOperationalTime." ::= { nwAtFwdCounters 4 } nwAtFwdCtrOutPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk packets that have been transmitted, system-wide, during nwAtFwdCtrOperationalTime." ::= { nwAtFwdCounters 5 } nwAtFwdCtrFwdPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk packets that have been forwarded, system-wide, during nwAtFwdCtrOperationalTime." ::= { nwAtFwdCounters 6 } nwAtFwdCtrFilteredPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk packets that have been administratively filtered, system-wide, during nwAtFwdCtrOperationalTime." ::= { nwAtFwdCounters 7 } nwAtFwdCtrDiscardPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk packets that have been discarded, system-wide, during nwAtFwdCtrOperationalTime." ::= { nwAtFwdCounters 8 } nwAtFwdCtrAddrErrPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk packets that have been discarded, system-wide, during nwAtFwdCtrOperationalTime because of addressing errors in the AppleTalk header." ::= { nwAtFwdCounters 9 } nwAtFwdCtrLenErrPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk packets that have been discarded, system-wide, during nwAtFwdCtrOperationalTime, because an invalid packet length is contained in the AppleTalk header." ::= { nwAtFwdCounters 10 } nwAtFwdCtrHdrErrPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of at packets that have been discarded, device-wide, during nwAtFwdCtrOperationalTime, because of an invalid at header." ::= { nwAtFwdCounters 11 } nwAtFwdCtrInBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of bytes in the AppleTalk packets that have been received, system-wide, during nwAtFwdCtrOperationalTime." ::= { nwAtFwdCounters 12 } nwAtFwdCtrOutBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of bytes in the AppleTalk packets that have been transmitted, system-wide, during nwAtFwdCtrOperationalTime." ::= { nwAtFwdCounters 13 } nwAtFwdCtrFwdBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of bytes in the AppleTalk packets that have been forwarded, system-wide, during nwAtFwdCtrOperationalTime." ::= { nwAtFwdCounters 14 } nwAtFwdCtrFilteredBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of bytes in the AppleTalk packets that have been administratively filtered, system-wide, during nwAtFwdCtrOperationalTime." ::= { nwAtFwdCounters 15 } nwAtFwdCtrDiscardBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of bytes in the AppleTalk packets that have been discarded, system wide, during nwAtFwdCtrOperationalTime." ::= { nwAtFwdCounters 16 } nwAtFwdCtrHostInPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk packets that have been successfully delivered to the local host, during nwAtFwdCtrOperationalTime." ::= { nwAtFwdCounters 17 } nwAtFwdCtrHostOutPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk packets that have been transmitted by the local host, during nwAtFwdCtrOperationalTime." ::= { nwAtFwdCounters 18 } nwAtFwdCtrHostDiscardPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk packets that have been discarded by the local host, during nwAtFwdCtrOperationalTiime, due to a lack of host resources." ::= { nwAtFwdCounters 19 } nwAtFwdCtrHostInBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of bytes in the AppleTalk packets that have been received by the local host, during nwAtFwdCtrOperationalTime." ::= { nwAtFwdCounters 20 } nwAtFwdCtrHostOutBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of bytes in the AppleTalk packets that have been transmitted by the local host, during nwAtFwdCtrOperationalTime." ::= { nwAtFwdCounters 21 } nwAtFwdCtrHostDiscardBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of bytes in the AppleTalk packets that have been discarded by the local host, during nwAtFwdCtrOperationalTime, due to a lack of host resources." ::= { nwAtFwdCounters 22 } -- at Forwarding Interface Table -- This table contains the managed objects used to set-up and configure -- each router port. nwAtFwdIfTable OBJECT-TYPE SYNTAX SEQUENCE OF NwAtFwdIfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains an entry for each router port. This table is indexed by nwAtFwdIfIndex, which indicates the value of MIB 2 ifindex, which identifies the router port for which each entry exists." ::= { nwAtFwdIfConfig 1 } nwAtFwdIfEntry OBJECT-TYPE SYNTAX NwAtFwdIfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry specifies the AppeTalk Routing Services configuration for the router port for which the entry exists." INDEX { nwAtFwdIfIndex } ::= { nwAtFwdIfTable 1 } NwAtFwdIfEntry ::= SEQUENCE { nwAtFwdIfIndex INTEGER, nwAtFwdIfAdminSTATUS INTEGER, nwAtFwdIfOperSTATUS INTEGER, nwAtFwdIfOperationalTime TimeTicks, nwAtFwdIfControl INTEGER, nwAtFwdIfMtu INTEGER, nwAtFwdIfForwarding INTEGER, nwAtFwdIfFrameType INTEGER, nwAtFwdIfAclIdentifier INTEGER, nwAtFwdIfAclSTATUS INTEGER, nwAtFwdIfCacheControl INTEGER, nwAtFwdIfCacheEntries Counter, nwAtFwdIfCacheHits Counter, nwAtFwdIfCacheMisses Counter } nwAtFwdIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the value of the MIB 2 ifIndex, which identifies the router port for which the entry exists." ::= { nwAtFwdIfEntry 1 } nwAtFwdIfAdminSTATUS OBJECT-TYPE SYNTAX INTEGER { other(1), disabled(2), enabled(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Sets the administrative state of AppleTalk Routing Services on the router port for which the entry exists. Enabled (3) causes AppleTalk Routing Services to become active. Disabled (2) causes it to become inactive." ::= { nwAtFwdIfEntry 2 } nwAtFwdIfOperSTATUS OBJECT-TYPE SYNTAX INTEGER { other(1), -- none of the following disabled(2), -- not running enabled(3), -- running pending-disable(4), -- shut-down in progress pending-enable(5), -- start-up in progress invalid-config(6) -- not running,invalid config } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the current operating condition of AppleTalk Routing Services on the AppleTalk router port for which the entry exists. The value of nwAtFwdIfOperStatus indicates any problem with the configuration of AppleTalk Routing Services on the router port. A value of 6 indicates that regardless of the state of nwAtFwdIfAdminStatus AppleTalk Routing Services is not operating because of an invalid port-level configuration." ::= { nwAtFwdIfEntry 3 } nwAtFwdIfOperationalTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the elapsed time, in hundredths of a second, that nwAtFwdIfOper Status has been in its current state." ::= { nwAtFwdIfEntry 4 } nwAtFwdIfControl OBJECT-TYPE SYNTAX INTEGER { other(1), add(2), delete(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect." ::= { nwAtFwdIfEntry 5 } nwAtFwdIfMtu OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the Maximum Transmissions Unit (MTU) for AppleTalk packets on the router port for which the entry exists. This includes the AppleTalk header and data, but does not include framing." ::= { nwAtFwdIfEntry 6 } nwAtFwdIfForwarding OBJECT-TYPE SYNTAX INTEGER { other(1), disabled(2), enabled(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Controls forwarding of AppleTalk packets on the AppleTalk router port for which the entry exists. Enabled (3) causes AppleTalk packets to be forwarded. Disabled (2) prevents AppleTalk packets from being forwarded." ::= { nwAtFwdIfEntry 7 } nwAtFwdIfFrameType OBJECT-TYPE SYNTAX INTEGER { -- valid media types other(1), -- experimental ethernet(2), -- ethernet snap(3), -- enet,fddi,and token ring nativewan(8), -- wan media types encapenet(9), -- wan media types encapenetsnap(11), -- wan media types encapfddisnap(16), -- wan media types canonical(17) -- special, tbd } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the framing type for AppleTalk packets forwarded on the router port for which the entry exists. Some frame types are only valid for specific media types. The comments reflect those valid media types." DEFVAL { snap } ::= { nwAtFwdIfEntry 8 } nwAtFwdIfAclIdentifier OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the Access Control ID of the access control list in effect for AppleTalk packets being routed on the router port for which the entry exists. A value of 0 indicates that no access control list is in effect." ::= { nwAtFwdIfEntry 9 } nwAtFwdIfAclSTATUS OBJECT-TYPE SYNTAX INTEGER { other(1), disabled(2), enabled(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Controls the operation of any access control list configured for AppleTalk traffic on the router port for which the entry exists. Enabled (3) applies the access control list indicated by the value of nwAtFwdIfAclIdentifier to all AppleTalk traffic being routed on the port. Disabled (2) prevents the access control list from being applied." ::= { nwAtFwdIfEntry 10 } nwAtFwdIfCacheControl OBJECT-TYPE SYNTAX INTEGER { other(1), disable(2), enable(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Controls AppleTalk Address caching on the router port for which the entry exists. When AppleTalk Address caching is enabled, AppleTalk Addresses used for address validation, filtering, and forwarding are stored in the cache. This cache is checked first before doing a full route table lockup, which speeds up the switching process. Enabled (3) turns on AppleTalk Address caching. Disabled (2) turns it off." ::= { nwAtFwdIfEntry 11 } nwAtFwdIfCacheEntries OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the number of entries in the AppleTalk Address cache on the router port for which the entry exists." ::= { nwAtFwdIfEntry 12 } nwAtFwdIfCacheHits OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the number of times entries in the AppleTalk Address cache have been used to provide the AppleTalk address required to validate, filter, or forward an AppleTalk packet on the router port." ::= { nwAtFwdIfEntry 13 } nwAtFwdIfCacheMisses OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the number of times the AppleTalk Address required to validate, filter, or forward an AppleTalk packet on the router port was not found in the AppleTalk Address cache." ::= { nwAtFwdIfEntry 14 } -- The at Interface Address Table -- This table contains the managed object used to setup and configure -- at addresses on a per router port basis. nwAtportTable OBJECT-TYPE SYNTAX SEQUENCE OF NwAtportEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains an entry for each router port configured for AppleTalk Routing Services." ::= { nwAtFwdIfConfig 2 } nwAtportEntry OBJECT-TYPE SYNTAX NwAtportEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry specifies the AppleTalk address information for the router port for which the entry exists." INDEX { nwAtportIndex } ::= { nwAtportTable 1 } NwAtportEntry ::= SEQUENCE { nwAtportIndex INTEGER, nwAtportDescr DisplayString, nwAtportType INTEGER, nwAtportNetStart AtNetworkNumber, nwAtportNetEnd AtNetworkNumber, nwAtportNetAddress AtDdpNodeAddress, nwAtportSTATUS INTEGER, nwAtportNetConfig INTEGER, nwAtportZoneConfig INTEGER, nwAtportZoneDefault AtName, nwAtportIfIndex INTEGER, nwAtportNetFrom AtDdpNodeAddress, nwAtportZoneFrom AtDdpNodeAddress, nwAtportInPkts Counter, nwAtportOutPkts Counter, nwAtportHome INTEGER, nwAtportCurrentZone AtName, nwAtportConflictPhysAddr OCTET STRING } nwAtportIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Indicates a unique value for each router port. The value of nwAtportIndex is an integer between 1 and the total number of ports configured for AppleTalk Routing Services." ::= { nwAtportEntry 1 } nwAtportDescr OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS mandatory DESCRIPTION "This text string provides a description of the port to the end-user; it must not contain anything but printable ASCII characters." ::= { nwAtportEntry 2 } -- objects throughout the MIB key off of nwAtportType to determine -- the format of address OCTET STRINGs. The address formats -- are as follows: -- localtalk, ethertalk1, ethertalk2, tokentalk, iptalk, -- fdditalk, smdstalk, arctalk, and virtual take the format of -- DdpNodeAddress -- serialPPP: null OCTET STRING -- serialNonstandard: vendor specific -- aurp: see AURP MIB to determine format -- frameRelay: 32 bit DLCI in network byte order -- (OCTET STRING (SIZE (4))) -- x25: X121Address (see RFC 1382) -- ip: IpAddress (see RFC 1155) -- osi: NSAP (OCTET STRING (SIZE (3..20))) -- decnetIV: 6 bit area, 10 bit host in network byte order -- (OCTET STRING (SIZE (2))) -- arap: ??? -- isdnInThePacketMode: ??? -- nonAppleTalk3Com: based on ifType -- ipx: 32 bit network number in network byte order followed -- by datalink address of host -- arns: 32 bit ARNS header -- hdlc: DdpNodeAddress or null OCTET STRING nwAtportType OBJECT-TYPE SYNTAX INTEGER { other(1), -- none of the following localtalk(2), ethertalk1(3), ethertalk2(4), tokentalk(5), iptalk(6), serialPPP(7), serialNonstandard(8), virtual(9), -- an internal interface fdditalk(10), arctalk(11), smdstalk(12), aurp(13), frameRelay(14), x25(15), ip(16), osi(17), decnetIV(18), arap(19), isdnInThePacketMode(20), nonAppleTalk3Com(21), ipx(22), arns(23), hdlc(24) } ACCESS read-write STATUS mandatory DESCRIPTION "The value of nwArPortType indicates which link-layer protocol is running immediately below DDP in the protocol stack on the router port for which the entry exists. The value of nwAtPortType determines the format of address octet stings throughout the entire AppleTalk MIB." ::= { nwAtportEntry 3 } nwAtportNetStart OBJECT-TYPE SYNTAX AtNetworkNumber ACCESS read-write STATUS mandatory DESCRIPTION "The first AppleTalk network address in the network range configured for the port. If the port is not a native AppleTalk port, this object will have the value of two octets of zero. Set this value to the first network address in the network range configured for the port." ::= { nwAtportEntry 4 } nwAtportNetEnd OBJECT-TYPE SYNTAX AtNetworkNumber ACCESS read-write STATUS mandatory DESCRIPTION "The last AppleTalk network address in the network range configured for the port. If the network to which this AppleTalk port is connected is a non-extended network, or if it is not a native AppleTalk port, the value for nwAtportNetEnd will be two octets of zero. Set this value to the last network address in the network range configured for the port." ::= { nwAtportEntry 5 } nwAtportNetAddress OBJECT-TYPE SYNTAX AtDdpNodeAddress ACCESS read-write STATUS mandatory DESCRIPTION "The AppleTalk node number configured for the port. This value may be used as a hint for an initial node number used during node-finding. If the port is not a native AppleTalk port, this object shall have the value of three octets of zero." ::= { nwAtportEntry 6 } nwAtportSTATUS OBJECT-TYPE SYNTAX INTEGER { routing(1), -- this port is fully configured and routing unconfigured(2), off(3), invalid(4), endNode(5), -- this port is acting as an end node offDueToConflict(6), -- port is off due to configuration other(7) -- none of the states defined above } ACCESS read-write STATUS mandatory DESCRIPTION "Indicates the current state of the router port's AppleTalk configuration. If either nwAtportNetConfig or nwApportZoneConfig are set to (5), conflictAverseSeed, and either the configured network number range or zone name seeded by the port conflict with the settings of a neighbor router, nwApPortStatus will have a value of (6), offDueToConflict." ::= { nwAtportEntry 7 } nwAtportNetConfig OBJECT-TYPE SYNTAX INTEGER { conflictOrientedSeed(1), garnered(2), guessed(3), unconfigured(4), conflictAverseSeed(5), softSeed(6) } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the network configuration type of the port. If the port is not a native AppleTalk port, this object will have an unconfigured (4) value." ::= { nwAtportEntry 8 } nwAtportZoneConfig OBJECT-TYPE SYNTAX INTEGER { conflictOrientedSeed(1), garnered(2), guessed(3), unconfigured(4), conflictAverseSeed(5), softSeed(6) } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the zone information configuration type of the port. If the port is not a native AppleTalk port, this object will have an unconfigured (4) value." ::= { nwAtportEntry 9 } nwAtportZoneDefault OBJECT-TYPE SYNTAX AtName ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the name of the default zone for the port. If the port only has one zone, that zone is represented here. If the port is not a native AppleTalk port, this object will contain an octet string of zero length." ::= { nwAtportEntry 10 } nwAtportIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Indicates the value of MIB 2 ifIndex, which identifies the router port for which the entry exists." ::= { nwAtportEntry 11 } nwAtportNetFrom OBJECT-TYPE SYNTAX AtDdpNodeAddress ACCESS read-only STATUS mandatory DESCRIPTION "When nwAtportNetConfig is set to garnered (2), this variable contains the DDP address of the entity from which the AppleTalk network number was garnered. When nwAtportNetConfig is set to conflictOrientedSeed (1), conflictAverseSeed (5), or softSeed (6), this variable contains the DDP address of an entity which supplied or confirmed the AppleTalk network number. If nwAtportNetConfig is set to guessed (3) or unconfigured (4), or if the AppleTalk Routing Services-enabled device has not received any network number confirmation, this object will be set to three octets of zero." ::= { nwAtportEntry 12 } nwAtportZoneFrom OBJECT-TYPE SYNTAX AtDdpNodeAddress ACCESS read-only STATUS mandatory DESCRIPTION "When nwAtportZoneConfig is set to garnered (2), this variable contains the DDP address of the entity from which the AppleTalk Zone List was garnered. When nwAtportZoneConfig is set to conflictOrientedSeed (1), conflictAverseSeed (5), or softSeed (6), this variable contains the DDP address of an entity which supplied or confirmed the AppleTalk zone information. If nwAtportZoneConfig is set to guessed (3) or unconfigured (4), or if the AppleTalk Routing Services-enabled device has not received any zone confirmation, this object will be set to three octets of zero." ::= { nwAtportEntry 13 } nwAtportInPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of AppleTalk packets received on the port." ::= { nwAtportEntry 14 } nwAtportOutPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of AppleTalk packets transmitted on the port." ::= { nwAtportEntry 15 } nwAtportHome OBJECT-TYPE SYNTAX INTEGER { home(1), notHome(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The value of nwAtportHome indicates whether or not the AppleTalk Routing Services-enabled device, the routing entity, is `homed' on the port for which the entry exists. If the entity is homed on the port, then it could perform NBP (Name Binding Protocol) registrations for services that it chooses to advertise." ::= { nwAtportEntry 16 } -- note that modifications to the following variable do -- not affect the nbpTable nwAtportCurrentZone OBJECT-TYPE SYNTAX AtName ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the current zone name for the port. In general, this is the zone name in which services on the port will be registered. If the port is not a native AppleTalk port, this object will contain an octet string of zero length." ::= { nwAtportEntry 17 } nwAtportConflictPhysAddr OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the link-layer address of the device which caused nwAtportStatus to be set to off (3). If this address is not available, or if nwAtportStatus is not set to off, this object will be a zero length octet string." ::= { nwAtportEntry 18 } -- at Forwarding Interfaces Counter Table -- This table contains the objects that specify the packet and byte counters -- for each configured at router port. nwAtFwdIfCtrTable OBJECT-TYPE SYNTAX SEQUENCE OF NwAtFwdIfCtrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains an entry for each router port configured and enabled for AppleTalk Routing Services." ::= { nwAtFwdIfCounters 1 } nwAtFwdIfCtrEntry OBJECT-TYPE SYNTAX NwAtFwdIfCtrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry indicates the current packet and byte count of AppleTalk packets on the router port for which the entry exists." INDEX { nwAtFwdIfCtrIfIndex } ::= { nwAtFwdIfCtrTable 1 } NwAtFwdIfCtrEntry ::= SEQUENCE { nwAtFwdIfCtrIfIndex INTEGER, nwAtFwdIfCtrAdminSTATUS INTEGER, nwAtFwdIfCtrReset INTEGER, nwAtFwdIfCtrOperationalTime TimeTicks, nwAtFwdIfCtrInPkts Counter, nwAtFwdIfCtrOutPkts Counter, nwAtFwdIfCtrFwdPkts Counter, nwAtFwdIfCtrFilteredPkts Counter, nwAtFwdIfCtrDiscardPkts Counter, nwAtFwdIfCtrAddrErrPkts Counter, nwAtFwdIfCtrLenErrPkts Counter, nwAtFwdIfCtrHdrErrPkts Counter, nwAtFwdIfCtrInBytes Counter, nwAtFwdIfCtrOutBytes Counter, nwAtFwdIfCtrFwdBytes Counter, nwAtFwdIfCtrFilteredBytes Counter, nwAtFwdIfCtrDiscardBytes Counter, nwAtFwdIfCtrHostInPkts Counter, nwAtFwdIfCtrHostOutPkts Counter, nwAtFwdIfCtrHostDiscardPkts Counter, nwAtFwdIfCtrHostInBytes Counter, nwAtFwdIfCtrHostOutBytes Counter, nwAtFwdIfCtrHostDiscardBytes Counter } nwAtFwdIfCtrIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the value MIB 2 ifindex, which identifies the router port for which the entry exists." ::= { nwAtFwdIfCtrEntry 1 } nwAtFwdIfCtrAdminSTATUS OBJECT-TYPE SYNTAX INTEGER { other(1), disabled(2), enabled(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Sets the administrative state of the per-port AppleTalk packet and byte counters on the router port for which the entry exists. Enabled (3) causes these counters to become active. Disabled (2) causes these counters to become inactive." ::= { nwAtFwdIfCtrEntry 2 } nwAtFwdIfCtrReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Resets the per-port AppleTalk packet and byte counters on the router port for which the entry exists. Reset (2) resets the counters to 0. nwAtFwdIfCtrOperationalTime is also reset to 0." ::= { nwAtFwdIfCtrEntry 3 } nwAtFwdIfCtrOperationalTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the amount of time, in hundredths of a second, that nwAtFwdIfCtrAdminStatus has been in the current state." ::= { nwAtFwdIfCtrEntry 4 } nwAtFwdIfCtrInPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk packets that have been received, during nwAtFwdIfCtrOperationaltime, on the router port for which the entry exists." ::= { nwAtFwdIfCtrEntry 5 } nwAtFwdIfCtrOutPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk packets that have been transmitted, during nwAtFwdIfCtrOperationaltime, on the router port for which the entry exists." ::= { nwAtFwdIfCtrEntry 6 } nwAtFwdIfCtrFwdPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk packets that have been forwarded, during nwAtFwdIfCtrOperationaltime, on the router port for which the entry exists." ::= { nwAtFwdIfCtrEntry 7 } nwAtFwdIfCtrFilteredPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk packets that have been administratively filtered, during nwAtFwdIfCtrOperationalTime, on the router port for which the entry exists." ::= { nwAtFwdIfCtrEntry 8 } nwAtFwdIfCtrDiscardPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk packets that have been discarded (dropped), during nwAtFwdIfCtrOperationalTime, on the router port for which the entry exists." ::= { nwAtFwdIfCtrEntry 9 } nwAtFwdIfCtrAddrErrPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk packets that have been discarded, because of addressing errors in the AppleTalk header, during nwAtFwdIfCtrOperationalTime, on the router port for which the entry exists." ::= { nwAtFwdIfCtrEntry 10 } nwAtFwdIfCtrLenErrPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk packets that have been discarded, because an invalid packet length was contained in the AppleTalk header, during nwAtFwdIfCtrOperationalTime, on the router port for which the entry exists." ::= { nwAtFwdIfCtrEntry 11 } nwAtFwdIfCtrHdrErrPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk packets that have been discarded, because of an invalid AppleTalk header, during nwAtFwdIfCtrOperationalTime, on the router port for which the entry exists." ::= { nwAtFwdIfCtrEntry 12 } nwAtFwdIfCtrInBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of bytes in the AppleTalk packets that have been received, during nwAtFwdIfCtrOperationalTime, on the router port for which the entry exists." ::= { nwAtFwdIfCtrEntry 13 } nwAtFwdIfCtrOutBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of bytes in the AppleTalk packets that have been transmitted, durin nwAtFwdIfCtrOperationalTime, on the router port for which the entry exists." ::= { nwAtFwdIfCtrEntry 14 } nwAtFwdIfCtrFwdBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of bytes in the AppleTalk packets that have been forwarded, during nwAtFwdIfCtrOperationalTime, on the router port for which the entry exists." ::= { nwAtFwdIfCtrEntry 15 } nwAtFwdIfCtrFilteredBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of bytes in the AppleTalk packets that have been administratively filtered, during nwAtFwdIfCtrOperationalTime, on the router port for which the entry exists." ::= { nwAtFwdIfCtrEntry 16 } nwAtFwdIfCtrDiscardBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of bytes in the AppleTalk packets that have been discarded, during nwAtFwdIfCtrOperationalTime, on the router port for which the entry exists." ::= { nwAtFwdIfCtrEntry 17 } nwAtFwdIfCtrHostInPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk packets that have been successfully delivered to the local host during nwAtFwdIfCtrOperationalTime, that were received on the router port for which the entry exists." ::= { nwAtFwdIfCtrEntry 18 } nwAtFwdIfCtrHostOutPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk packets that have been transmitted by the local host, during nwAtFwdIfCtrOperationalTime, on the router port for which the entry exists." ::= { nwAtFwdIfCtrEntry 19 } nwAtFwdIfCtrHostDiscardPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk packets that have been discarded by the local host due to a lack of host resources during nwAtFwdIfCtrOperationalTime, that were received on the router port for which the entry exists." ::= { nwAtFwdIfCtrEntry 20 } nwAtFwdIfCtrHostInBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of bytes in the AppleTalk packets that have been successfully delivered to the local host, during nwAtFwdIfCtrOperationalTime, that were received on the router port for which the entry exists." ::= { nwAtFwdIfCtrEntry 21 } nwAtFwdIfCtrHostOutBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of bytes in the AppleTalk packets that have been transmitted by the local host, during nwAtFwdIfCtrOperationalTime, on the router port for which the entry exists." ::= { nwAtFwdIfCtrEntry 22 } nwAtFwdIfCtrHostDiscardBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of bytes in the AppleTalk packets that have been discarded by the local host, due to a lack of host resources during nwAtFwdIfCtrOperationalTime, that were received on the router port for which the entry exists." ::= { nwAtFwdIfCtrEntry 23 } -- DistanceVector-based Protocols -- This group contains the managed objects for the Appletalk Routing Protocol, -- RTMP DistanceVector based routing. -- AppleTalk Proto System Configuration Parameters -- This group contains the objects that pertain to the setup and -- configuration of the AppleTalk Proto DistanceVector based routing protocol. nwAtProtoAdminSTATUS OBJECT-TYPE SYNTAX INTEGER { other(1), -- none of the following disabled(2), -- shutdown the router enabled(3) -- startup the router } ACCESS read-write STATUS mandatory DESCRIPTION "Sets the administrative state of the AppleTalk distance-vector based routing protocol system-wide. Enabled (3) causes the routing protocol to become active on all router ports configured and enabled for AppleTalk Routing Services. Disabled (2) causes the routing protocol to become inactive." ::= { nwAtProtoConfig 1 } nwAtProtoOperSTATUS OBJECT-TYPE SYNTAX INTEGER { other(1), -- none of the following disabled(2), -- not running enabled(3), -- running pending-disable(4), -- shut-down in progress pending-enable(5) -- start-up in progress } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the current operating condition of the AppleTalk Routing Services distance-vector-based routing protocol, system-wide. The value of nwAtProtoOperStatus indicates any problem with the routing protocol configuration. A value of 6 indicates that regardless of the value of nwAtProtoAdminStatus, the routing protocol is not operating because of an invalid configuration." ::= { nwAtProtoConfig 2 } nwAtProtoAdminReset OBJECT-TYPE SYNTAX INTEGER { other(1), -- none of the following reset(2) -- force a reset } ACCESS read-write STATUS mandatory DESCRIPTION "Resets the routing protocol. Reset (2) forces a system-wide restart of the protocol without a graceful shutdown on any active router ports." ::= { nwAtProtoConfig 3 } nwAtProtoOperationalTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the elapsed time, in hundredths of a second, that nwAtProtoOperStatus has been in the current state." ::= { nwAtProtoConfig 4 } nwAtProtoVersion OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the current revision level of the AppleTalk routing protocol firmware, in textual format." ::= { nwAtProtoConfig 5 } nwAtProtoStackSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the stack size of the AppleTalk routing protocol thread. In order for a change of this value to take effect, the protocol (nwAtProtoAdminReset), AppleTalk Routing Services (nwAtProtoAdminReset), or the device running Routing Services must be reset." ::= { nwAtProtoConfig 6 } nwAtProtoThreadPriority OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the run-time execution priority of the AppleTalk routing protocol thread. In order for a change of this value to take effect, the AppleTalk protocol (nwAtProtoAdminReset), AppleTalk Routing Services (nwAtProtoAdminReset), or the device running Routing Services must be reset." ::= { nwAtProtoConfig 7 } nwAtProtoDatabaseThreshold OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the run-time maximum number of entries that can be held in the AppleTalk routing protocol route table." ::= { nwAtProtoConfig 8 } nwAtProtoAgeOut OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the amount of time (in seconds) an inactive entry will be allowed to remain in the AppleTalk routing protocol routing table, before it is deleted, or aged-out." ::= { nwAtProtoConfig 9 } nwAtProtoHoldDown OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect." ::= { nwAtProtoConfig 10 } -- AppleTalk Routing Protocol System (aggregate) Counters -- This group contains the aggregate (device-wide) AppleTalk Routing Protocol -- packet and byte counters. nwAtProtoCtrAdminSTATUS OBJECT-TYPE SYNTAX INTEGER { other(1), disabled(2), enabled(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Sets the administrative state of the aggregate (system-wide) AppleTalk routing protocol packet and byte counters. Enabled (3)causes these counters to become active. Disabled (2) causes these counters to be come inactive." ::= { nwAtProtoCounters 1 } nwAtProtoCtrReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Resets the aggregate (system-wide) AppleTalk distance-vector based routing protocol packet and byte counters. Reset (2) resets the AppleTalk aggregate counters to 0. nwAtProtoCtrOperationalTime is also reset to 0." ::= { nwAtProtoCounters 2 } nwAtProtoCtrOperationalTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the elapsed time, in hundreds of seconds, that nwAtProtoCtrAdminStatus, has been in the current administrative state." ::= { nwAtProtoCounters 3 } nwAtProtoCtrInPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk routing protocol packets that have been received, system-wide, during nwAtProtoCtrOperationalTime." ::= { nwAtProtoCounters 4 } nwAtProtoCtrOutPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk routing protocol packets that have been transmitted, system-wide, during nwAtProtoCtrOperationalTime." ::= { nwAtProtoCounters 5 } nwAtProtoCtrFilteredPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk routing protocol packets that have been administratively filtered, system-wide, during nwAtProtoCtrOperationalTime." ::= { nwAtProtoCounters 6 } nwAtProtoCtrDiscardPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk routing protocol packets that have been discarded, system-wide, during nwAtProtoCtrOperationalTime." ::= { nwAtProtoCounters 7 } nwAtProtoCtrInBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of bytes in the AppleTalk routing protocol packets that have been received, system-wide, during nwAtProtoCtrOperationalTime." ::= { nwAtProtoCounters 8 } nwAtProtoCtrOutBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of bytes in the AppleTalk routing protocol packets that have been transmitted, system-wide, during nwAtProtoCtrOperationalTime." ::= { nwAtProtoCounters 9 } nwAtProtoCtrFilteredBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of bytes in the AppleTalk routing protocol packets that have been administratively filtered, system-wide, during nwAtProtoCtrOperationalTime." ::= { nwAtProtoCounters 10 } nwAtProtoCtrDiscardBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of bytes in the AppleTalk routing protocol packets that have been discarded, system-wide during nwAtProtoCtrOperationalTime." ::= { nwAtProtoCounters 11 } -- at Protocol Interface Table nwAtProtoIfTable OBJECT-TYPE SYNTAX SEQUENCE OF NwAtProtoIfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains an entry for each router port. Each entry can contain different values, allowing the routing protocol configuration to vary from router port to router port. This table is indexed by nwAtProtoIfIndex, which indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists." ::= { nwAtProtoIfConfig 1 } nwAtProtoIfEntry OBJECT-TYPE SYNTAX NwAtProtoIfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry contains the AppleTalk routing protocol configuration for the router port for which the entry exists." INDEX { nwAtProtoIfIndex } ::= { nwAtProtoIfTable 1 } NwAtProtoIfEntry ::= SEQUENCE { nwAtProtoIfIndex INTEGER, nwAtProtoIfAdminSTATUS INTEGER, nwAtProtoIfOperSTATUS INTEGER, nwAtProtoIfOperationalTime TimeTicks, nwAtProtoIfVersion INTEGER, nwAtProtoIfAdvertisement INTEGER, nwAtProtoIfFloodDelay INTEGER, nwAtProtoIfRequestDelay INTEGER, nwAtProtoIfPriority INTEGER, nwAtProtoIfHelloTimer INTEGER, nwAtProtoIfSplitHorizon INTEGER, nwAtProtoIfPoisonReverse INTEGER, nwAtProtoIfSnooping INTEGER, nwAtProtoIfType INTEGER, nwAtProtoIfXmitCost INTEGER, nwAtProtoIfAclIdentifier INTEGER, nwAtProtoIfAclSTATUS INTEGER } nwAtProtoIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists." ::= { nwAtProtoIfEntry 1 } nwAtProtoIfAdminSTATUS OBJECT-TYPE SYNTAX INTEGER { other(1), disabled(2), enabled(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Sets the administrative state of the AppleTalk routing protocol on the router port for which the entry exists. Enabled (3) causes the routing protocol to become active on the router port. Disabled (2) causes it to become inactive." DEFVAL { disabled } ::= { nwAtProtoIfEntry 2 } nwAtProtoIfOperSTATUS OBJECT-TYPE SYNTAX INTEGER { other(1), -- none of the following disabled(2), -- not running enabled(3), -- running pending-disable(4), -- shut-down in progress pending-enable(5) -- start-up in progress } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the current operating condition of the AppleTalk routing protocol on the router port for which the entry exists. The value of nwAtProtoIfOperStatus indicates any problem with your AppleTalk routing protocol configuration on the router port. A value of 6 indicates that regardless of the value of nwAtProtoIfAdminStatus, the routing protocol is not operating on the router port because of an invalid configuration." ::= { nwAtProtoIfEntry 3 } nwAtProtoIfOperationalTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the elapsed time, in hundreds of seconds, that nwAtProtoIfOperStatus has been in the current state." ::= { nwAtProtoIfEntry 4 } nwAtProtoIfVersion OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Indicates the revision level of AppleTalk routing protocol firmware on the router port for which the entry exists, in textual format." ::= { nwAtProtoIfEntry 5 } nwAtProtoIfAdvertisement OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This specifies the periodic interval (in seconds) that the AppleTalk routing protocol agent will advertise routes on this DECnet routing port." DEFVAL { 60 } ::= { nwAtProtoIfEntry 6 } nwAtProtoIfFloodDelay OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol specific MIBs. Setting this object has no effect" ::= { nwAtProtoIfEntry 7 } nwAtProtoIfRequestDelay OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol specific MIBs. Setting this object has no effect." ::= { nwAtProtoIfEntry 8 } nwAtProtoIfPriority OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Sets the priority of the AppleTalk routing protocol on the router port for which the entry exists." ::= { nwAtProtoIfEntry 9 } nwAtProtoIfHelloTimer OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol specific MIBs. Setting this object has no effect." ::= { nwAtProtoIfEntry 10 } nwAtProtoIfSplitHorizon OBJECT-TYPE SYNTAX INTEGER { other(1), disabled(2), enabled(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Sets the operating condition of Split Horizon on the router port for which the entry exists. When Split Horizon is enabled, the AppleTalk routing protocol keeps track of which router port route information is received on, and prevents information about a route form being sent back out the same router port it was received on." DEFVAL { enabled } ::= { nwAtProtoIfEntry 11 } nwAtProtoIfPoisonReverse OBJECT-TYPE SYNTAX INTEGER { other(1), disabled(2), enabled(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Sets the operating condition of Poison Reverse on the router port for which the entry exists. When Poison Reverse is enabled, the AppleTalk routing protocol advertises any downed routes as unreachable during the period of time that it must wait before removing the route from the route table." DEFVAL { disabled } ::= { nwAtProtoIfEntry 12 } nwAtProtoIfSnooping OBJECT-TYPE SYNTAX INTEGER { other(1), disabled(2), enabled(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Controls the operation of AppleTalk routing protocol Snooping on the router port. When AppleTalk routing protocol Snooping is enabled, the routing protocol operates in passive mode, so that it receives route information, builds and maintains a route table, but does not advertise or send updates on the router port for which the entry exists." DEFVAL { disabled } ::= { nwAtProtoIfEntry 13 } nwAtProtoIfType OBJECT-TYPE SYNTAX INTEGER { other(1), bma(2), nbma(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Indicates whether the directly connected network segment does or does not support broadcast media access. If broadcast media access is supported, AppleTalk routing protocol advertisements are sent out one broadcast packet per port. If broadcast media is not supported, AppleTalk routing protocol advertisements are sent to each neighbor." ::= { nwAtProtoIfEntry 14 } nwAtProtoIfXmitCost OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Sets the cost of transmitting a packet on the network segment connected to router port for which the entry exists." ::= { nwAtProtoIfEntry 15 } nwAtProtoIfAclIdentifier OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the Access Control List ID of the access control list in effect for AppleTalk routing protocol packets on the router port for which the entry exists. A value of 0 indicates that there is no access control list in effect for AppleTalk routing protocol packets on the router port." ::= { nwAtProtoIfEntry 16 } nwAtProtoIfAclSTATUS OBJECT-TYPE SYNTAX INTEGER { other(1), disabled(2), enabled(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Controls the operation of the access control list identified by nwAtProtoIfAclIdentifier. Enabled (3) causes the access control list to be applied to all AppleTalk routing protocol packet traffic on the router port for which the entry exists. Disabled (2) prevents the access control list from being applied." ::= { nwAtProtoIfEntry 17 } -- AppleTalk Protocol Interface Counters Table -- This table contains the managed objects for AppleTalk protocols packet and -- byte counter on a per router port basis. nwAtProtoIfCtrTable OBJECT-TYPE SYNTAX SEQUENCE OF NwAtProtoIfCtrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains the AppleTalk packet and byte counters for each router port on this device." ::= { nwAtProtoIfCounters 1 } nwAtProtoIfCtrEntry OBJECT-TYPE SYNTAX NwAtProtoIfCtrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry specifies the DECnet Phase IV packet and byte counters on a per router port basis." INDEX { nwAtProtoIfCtrIfIndex } ::= { nwAtProtoIfCtrTable 1 } NwAtProtoIfCtrEntry ::= SEQUENCE { nwAtProtoIfCtrIfIndex INTEGER, nwAtProtoIfCtrAdminSTATUS INTEGER, nwAtProtoIfCtrReset INTEGER, nwAtProtoIfCtrOperationalTime TimeTicks, nwAtProtoIfCtrInPkts Counter, nwAtProtoIfCtrOutPkts Counter, nwAtProtoIfCtrFilteredPkts Counter, nwAtProtoIfCtrDiscardPkts Counter, nwAtProtoIfCtrInBytes Counter, nwAtProtoIfCtrOutBytes Counter, nwAtProtoIfCtrFilteredBytes Counter, nwAtProtoIfCtrDiscardBytes Counter } nwAtProtoIfCtrIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This is the primary index into the AppleTalk interface counter table. This number corresponds to the index into the mib2 InterfaceTable which describes the router port for which the entry exists." ::= { nwAtProtoIfCtrEntry 1 } nwAtProtoIfCtrAdminSTATUS OBJECT-TYPE SYNTAX INTEGER { other(1), disabled(2), enabled(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Sets the administrative state of the AppleTalk packet and byte counters on the router port for which the entry exists. enabled(3) causes these counters to become active on the configured AppleTalk router port. disabled(2) causes these counters to become inactive on the configured AppleTalk router port." ::= { nwAtProtoIfCtrEntry 2 } nwAtProtoIfCtrReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Resets the AppleTalk packet and byte counters on the router port for which the entry exists. reset (2) resets the interface-specific counters to 0. nwAtProtoIfCtrOperationalTime is also reset to 0." ::= { nwAtProtoIfCtrEntry 3 } nwAtProtoIfCtrOperationalTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the amount of time (No. of time ticks) that the interface-specific AppleTalk packet and byte counters have been active on the router port for which the entry exists." ::= { nwAtProtoIfCtrEntry 4 } nwAtProtoIfCtrInPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk packets that have been received, on the router port for which the entry exists, during nwAtProtoIfCtrOperationalTime." ::= { nwAtProtoIfCtrEntry 5 } nwAtProtoIfCtrOutPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk packets that have been forwarded, on the router port for which the entry exists, during nwAtProtoIfCtrOperationalTime." ::= { nwAtProtoIfCtrEntry 6 } nwAtProtoIfCtrFilteredPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk packets that have been administratively filtered, on the router port for which this entry exists, during nwAtProtoIfCtrOperationalTime." ::= { nwAtProtoIfCtrEntry 7 } nwAtProtoIfCtrDiscardPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of AppleTalk packets that have been discarded, on the router port for which the entry exists, during nwAtProtoIfCtrOperationalTime." ::= { nwAtProtoIfCtrEntry 8 } nwAtProtoIfCtrInBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of bytes in the AppleTalk packets that have been received, on the router port for which the entry exists, during nwAtProtoIfCtrOperationalTime." ::= { nwAtProtoIfCtrEntry 9 } nwAtProtoIfCtrOutBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of bytes in the AppleTalk packets that have been forwarded, on the router port for which the entry exists, during nwAtProtoIfCtrOperationalTime." ::= { nwAtProtoIfCtrEntry 10 } nwAtProtoIfCtrFilteredBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of bytes in the AppleTalk packets that have been administratively filtered, that were received on the router port for which the entry exists, during nwAtProtoIfCtrOperationalTime." ::= { nwAtProtoIfCtrEntry 11 } nwAtProtoIfCtrDiscardBytes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of bytes in the AppleTalk packets that have been discarded, that were received on the router port for which the entry exists, during nwAtIfCtrOperationalTime." ::= { nwAtProtoIfCtrEntry 12 } -- at Forward Information Base (FIB) Group -- This group contains the managed objects for the forwarding table of the -- at router. nwAtFibTable OBJECT-TYPE SYNTAX SEQUENCE OF NwAtFibEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains an entry for each route being used to forward AppleTalk data packets." ::= { nwAtFib 1 } nwAtFibEntry OBJECT-TYPE SYNTAX NwAtFibEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry in the table describes an AppleTalk route to a particular destination." INDEX { nwAtFibStartNet } ::= { nwAtFibTable 1 } NwAtFibEntry ::= SEQUENCE { nwAtFibStartNet AtNetworkNumber, nwAtFibEndNet AtNetworkNumber, nwAtFibNextHop AtDdpNodeAddress, nwAtFibNextHopIf INTEGER, nwAtFibHops INTEGER, nwAtFibRouteType INTEGER } nwAtFibStartNet OBJECT-TYPE SYNTAX AtNetworkNumber ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the start of the network range for the route." ::= { nwAtFibEntry 1 } nwAtFibEndNet OBJECT-TYPE SYNTAX AtNetworkNumber ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the end of the network range for the route." ::= { nwAtFibEntry 2 } nwAtFibNextHop OBJECT-TYPE SYNTAX AtDdpNodeAddress ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the full AppleTalk network address of the next hop router for the route. An address of all zeros indicates a directly connected net." ::= { nwAtFibEntry 3 } nwAtFibNextHopIf OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the value of MIB 2 ifindex, which identifies the router port through which the next hop node exists. Packets destined for the network specified by the entry will be forwarded on this router port." ::= { nwAtFibEntry 4 } nwAtFibHops OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the number of hops required to reach the destination for which the entry exists. It is considered as metric 1." ::= { nwAtFibEntry 5 } nwAtFibRouteType OBJECT-TYPE SYNTAX INTEGER { other(1), appleTalk(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the type of route (Allows for PPP entries later)." ::= { nwAtFibEntry 6 } -- at Host End Systems Group -- This group contains the managed objects which control the use of the -- Address Resolution Protocol (ARP) for mapping host addresses to physical -- addresses of each router port ARP cache. Mechanisms are also -- provided which allow 'snooping' such that all directly connected -- end systems using ARP can be discovered along with their addresses. nwAtHostsTimeToLive OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the amount of time (in minutes) that an entry can remain in the AARP cache." ::= { nwAtHostsSystem 1 } nwAtHostsRetryCount OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the maximum number of times AppleTalk Routing Services will retry each attempt to resolve a host address." ::= { nwAtHostsSystem 2 } -- at Host Interfaces Table -- This table contains the objects that specify the control information for -- maintaining the ARP cache (at Net-to-Media Table). nwAtHostCtlTable OBJECT-TYPE SYNTAX SEQUENCE OF NwAtHostCtlEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains the control information for maintaining an AARP cache on each router port. Note that the cache entries are maintained by theAppleTalk Address Resolution Protocol Table of the AppleTalk MIB." ::= { nwAtHostsInterfaces 1 } nwAtHostCtlEntry OBJECT-TYPE SYNTAX NwAtHostCtlEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry contains the control information for the ARP cache on the router port indicated by the value nwAtHostCtlIfIndex." INDEX { nwAtHostCtlIfIndex } ::= { nwAtHostCtlTable 1 } NwAtHostCtlEntry ::= SEQUENCE { nwAtHostCtlIfIndex INTEGER, nwAtHostCtlAdminSTATUS INTEGER, nwAtHostCtlOperSTATUS INTEGER, nwAtHostCtlOperationalTime TimeTicks, nwAtHostCtlProtocol INTEGER, nwAtHostCtlSnooping INTEGER, nwAtHostCtlProxy INTEGER, nwAtHostCtlCacheMax INTEGER, nwAtHostCtlCacheSize INTEGER, nwAtHostCtlNumStatics Counter, nwAtHostCtlNumDynamics Counter, nwAtHostCtlCacheHits Counter, nwAtHostCtlCacheMisses Counter } nwAtHostCtlIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the value of MIB2 ifindex, which identifies the router port for which the entry exists." ::= { nwAtHostCtlEntry 1 } nwAtHostCtlAdminSTATUS OBJECT-TYPE SYNTAX INTEGER { other(1), disable(2), enable(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Sets the administrative state of the AARP cache on the router port for which the entry exists. Enabled (3) causes AARP caching to become active. Disabled (2) causes AARP caching to perform a graceful shutdown." ::= { nwAtHostCtlEntry 2 } nwAtHostCtlOperSTATUS OBJECT-TYPE SYNTAX INTEGER { other(1), -- none of the following disabled(2), -- not running enabled(3), -- running pending-disable(4), -- shut-down in progress pending-enable(5) -- start-up in progress } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the current operating condition of the AARP Table on the router port for which the entry exists." ::= { nwAtHostCtlEntry 3 } nwAtHostCtlOperationalTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the amount of time, in hundredths of a second, that nwAtHostCtlOperStatus has been in the current state." ::= { nwAtHostCtlEntry 4 } nwAtHostCtlProtocol OBJECT-TYPE SYNTAX INTEGER { other(1), disable(2), enable(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Controls the operation of the AARP protocol on the router port for which the entry exists." ::= { nwAtHostCtlEntry 5 } nwAtHostCtlSnooping OBJECT-TYPE SYNTAX INTEGER { other(1), disable(2), enable(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Controls AARP Snooping on the router port for which the entry exists. Given the AARP protocol is enabled, setting nwAtHostCtlIfSnooping to enabled (3) turns on AARP Snooping. When AARP Snooping is enabled the source AppleTalk and physical addresses of all AARP packets received on the router port are added to the AARP Table." ::= { nwAtHostCtlEntry 6 } nwAtHostCtlProxy OBJECT-TYPE SYNTAX INTEGER { other(1), disable(2), enable(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect." ::= { nwAtHostCtlEntry 7 } nwAtHostCtlCacheMax OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Indicates the maximum number of entry slots the AARP cache can consist of. nwAtHostCtlCacheMax cannot be set to less than 16. Setting this value does not allocate any memory for the cache." ::= { nwAtHostCtlEntry 8 } nwAtHostCtlCacheSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Indicates the current number of entry slots in the AARP cache on the router port for which the entry exists. The cache automatically resizes to accommodate all entries up to the maximum number of entries set by nwAtHostCtlCacheMax." ::= { nwAtHostCtlEntry 9 } nwAtHostCtlNumStatics OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of static entries in the AARP cache on the router port for which the entry exists. Static entries remain in the cache until they are administratively removed." ::= { nwAtHostCtlEntry 10 } nwAtHostCtlNumDynamics OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the number of dynamic entries in the AARP cache on the router port for which the entry exists. Dynamic entries area added and aged out by the AARP protocol." ::= { nwAtHostCtlEntry 11 } nwAtHostCtlCacheHits OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the number of times an entry in the AARP cache has been used to successfully provide the physical address required to forward an AppleTalk packet on the router port for which the entry exists." ::= { nwAtHostCtlEntry 12 } nwAtHostCtlCacheMisses OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the number of times the physical address required to forward an AppleTalk packet has not been found in the AARP cache on the router port for which the entry exists." ::= { nwAtHostCtlEntry 13 } -- at Access Control List Table -- This table contains the managed objects for the Access Control Lists -- within the at Router. Access Control Lists allow configuration of -- restricted access to networks and protocols reachable thru the at -- Router device. Access Control Lists can be defined with these -- objects and then be independently applied to at forwarding router ports. nwAtAclValidEntries OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the number of valid entries that exist in the Access Control List Table." ::= { nwAtAccessControl 1 } nwAtAclTable OBJECT-TYPE SYNTAX SEQUENCE OF NwAtAclEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains the Access Control List information for theAppleTalk protocol. This table contains entries, each of which allows packet forwarding between source/destination pairs to be permitted or denied. The particular list is identified by the access control list ID. Each list may contain multiple entries ordered by sequence number. When a particular access control list is searched, it is searched in sequence number order and the first match found ends the search. If no match is found, access defaults to permitted." ::= { nwAtAccessControl 2 } nwAtAclEntry OBJECT-TYPE SYNTAX NwAtAclEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry contains AppleTalk source/destination access information." INDEX { nwAtAclIdentifier, nwAtAclSequence } ::= { nwAtAclTable 1 } NwAtAclEntry ::= SEQUENCE { nwAtAclIdentifier INTEGER, nwAtAclSequence INTEGER, nwAtAclPermission INTEGER, nwAtAclMatches Counter, nwAtAclDestZone AtName, nwAtAclSrcZone AtName } nwAtAclIdentifier OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This is the primary (major) index into the AppleTalk access control list table. Essentially, this identifies the access control list by a unique identifier (at least 1) and is arbitrarily assigned by the user. All entries that have the same ID belong to the same access control list." ::= { nwAtAclEntry 1 } nwAtAclSequence OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This is the secondary (minor) index into the AppleTalk access control list table. This number corresponds to a sequence number used to order multiple entries within the same access control list." ::= { nwAtAclEntry 2 } nwAtAclPermission OBJECT-TYPE SYNTAX INTEGER { other(1), invalid(2), permit(3), deny(4), permit-bidirectional(5), deny-bidirectional(6) } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies whether access is allowed or denied between the source and destination address pairs. Note that source and destination are interchangeable when bi-directional control is selected. To remove an existing entry set invalid (2), and it will disappear after reboot." ::= { nwAtAclEntry 3 } nwAtAclMatches OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the number of matches on this entry that have resulted in the access restriction permit/deny being applied as part of the forwarding process." ::= { nwAtAclEntry 4 } nwAtAclDestZone OBJECT-TYPE SYNTAX AtName ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the destination zone name used to compare for matches on the access control list." ::= { nwAtAclEntry 5 } nwAtAclSrcZone OBJECT-TYPE SYNTAX AtName ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the source zone to be used to compare for matches on the access control list." ::= { nwAtAclEntry 6 } -- AppleTalk Event Group nwAtEventAdminSTATUS OBJECT-TYPE SYNTAX INTEGER { other(1), disabled(2), enabled(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Sets the administrative state of AppleTalk event logging. Enabled (3) causes the event log to become active. Disabled (2) causes the event log to become inactive." ::= { nwAtEventLogConfig 1 } nwAtEventMaxEntries OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Sets the maximum number of entries allowed in the event log table. When the number of entries reaches the value of nwAtEventMaxEntries the first (oldest) entry is deleted to allow a new entry to be added." ::= { nwAtEventLogConfig 2 } nwAtEventTraceAll OBJECT-TYPE SYNTAX INTEGER { other(1), disabled(2), enabled(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Enabled (3) allows logging of all event types on all router ports from all protocols and components. Disabled (2) causes the event log filter table to specify which events to log." ::= { nwAtEventLogConfig 3 } -- Event Log Filter Table -- The Event Log Filter Table contains the managed objects used to set-up -- and configure log entries. nwAtEventFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF NwAtEventFilterEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains an entry for each event filter configured for AppleTalk Routing Service's events." ::= { nwAtEventLogFilterTable 1 } nwAtEventFilterEntry OBJECT-TYPE SYNTAX NwAtEventFilterEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry describes an event filter which defines a particular type of event to be logged to the event log. The value of nwIpEventProtocol indicates the value used in either the nwRtgProtocolTable or the nwComponentTable Cabletron Routing Services MIB, which indentifies the protocol to which the entry exists." INDEX { nwAtEventFltrProtocol, nwAtEventFltrIfNum } ::= { nwAtEventFilterTable 1 } NwAtEventFilterEntry ::= SEQUENCE { nwAtEventFltrProtocol INTEGER, nwAtEventFltrIfNum INTEGER, nwAtEventFltrControl INTEGER, nwAtEventFltrType INTEGER, nwAtEventFltrSeverity INTEGER, nwAtEventFltrAction INTEGER } nwAtEventFltrProtocol OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the value of the Cabletron Routing Services MIB nwRtgProtocolInstance or nwComponentRtgInstance, which identifies the protocol involved in the event for which the event filter exists." ::= { nwAtEventFilterEntry 1 } nwAtEventFltrIfNum OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Specifies the router port involved in the event for which the event filter exists." ::= { nwAtEventFilterEntry 2 } nwAtEventFltrControl OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2), add(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Set this value to 3 to add the entry to the event log table. Set this value to 2 to remove the entry from the event filter table." ::= { nwAtEventFilterEntry 3 } nwAtEventFltrType OBJECT-TYPE SYNTAX INTEGER { misc(1), timer(2), rcv(4), xmit(8), event(16), error(32) } ACCESS read-write STATUS mandatory DESCRIPTION "This 6 bit mask specifies the types of events to be logged. By default all 6 bits are set to 1, indicating that all types of events are to be logged. Setting any bit to 0 removes an event type from this field and prevents that type of event from being logged. Setting any bit to 1 adds an event type to this field and enables that type of event to be logged. " ::= { nwAtEventFilterEntry 4 } nwAtEventFltrSeverity OBJECT-TYPE SYNTAX INTEGER { highest(1), highmed(2), highlow(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the level of severity an event must meet in order to be logged. Controls the amount of event logging by ignoring events of a lower priority than specified by this filter value. `Highmed' ignores only events of the lowest severity. `Highlow' logs all events highest priority through lowest. `Highest' severity causes all events except those of the highest severity to be ignored. `Highmed' severity is the default setting which causes only events of the lowest severity to be ignored. `Highlow' severity logs all events, regardless of severity." ::= { nwAtEventFilterEntry 5 } nwAtEventFltrAction OBJECT-TYPE SYNTAX INTEGER { log(1), trap(2), log-trap(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies how the events are to be logged. Logging to the `log' stores the events in the event log table (nwIpEventFltrAction). Logging to `trap' sends events out through the trap mechanism." ::= { nwAtEventFilterEntry 6 } -- Event Log Table -- The Event Log Table contains the logged events. nwAtEventTable OBJECT-TYPE SYNTAX SEQUENCE OF NwAtEventEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains an entry for each event that has been logged." ::= { nwAtEventLogTable 1 } nwAtEventEntry OBJECT-TYPE SYNTAX NwAtEventEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry contains the information about an event that has been logged to the event table." INDEX { nwAtEventNumber } ::= { nwAtEventTable 1 } NwAtEventEntry ::= SEQUENCE { nwAtEventNumber INTEGER, nwAtEventTime TimeTicks, nwAtEventType INTEGER, nwAtEventSeverity INTEGER, nwAtEventProtocol INTEGER, nwAtEventIfNum INTEGER, nwAtEventTextString OCTET STRING } nwAtEventNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "An ordinal value assigned to the event for which the log entry exists. nwAtEvnetNumber is assigned so that each event in the event log can be uniquely identified by the value of nwAtEventNumber." ::= { nwAtEventEntry 1 } nwAtEventTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the time at which the event was logged to the event log" ::= { nwAtEventEntry 2 } nwAtEventType OBJECT-TYPE SYNTAX INTEGER { misc(1), timer(2), rcv(4), xmit(8), event(16), error(32) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the type of event that was logged." ::= { nwAtEventEntry 3 } nwAtEventSeverity OBJECT-TYPE SYNTAX INTEGER { highest(1), highmed(2), highlow(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the severity that was assigned to this event." ::= { nwAtEventEntry 4 } nwAtEventProtocol OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the value of the Cabletron Routing Services MIB nwRtgProtocolInstance or nwComponentInstance which identifies the protocol or component that was involved in the event." ::= { nwAtEventEntry 5 } nwAtEventIfNum OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the router port that was involved in the event." ::= { nwAtEventEntry 6 } nwAtEventTextString OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "Contains the actual text string that was logged." ::= { nwAtEventEntry 7 } -- AppleTalk Outbound Diagnostics Group nwAtNetDiagOutboundNetAddress OBJECT-TYPE SYNTAX AtDdpNodeAddress ACCESS read-write STATUS mandatory DESCRIPTION "The AppleTalk Network Address of a node with which the diagnostic test will directly correspond." ::= { nwAtNetDiagOutbound 1 } nwAtNetDiagOutboundPort OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "An integer representing the port through which the diagnostic test will broadcast or multicast packets." ::= { nwAtNetDiagOutbound 2 } nwAtNetDiagOutboundTimeout OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "An integer representing the number of seconds before a diagnostic request will time out." ::= { nwAtNetDiagOutbound 3 } nwAtNetDiagOutboundRetries OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "An integer representing the number of times a request will be repeated before failure." ::= { nwAtNetDiagOutbound 4 } nwAtNetDiagOutboundATEchoType OBJECT-TYPE SYNTAX INTEGER { noAction(1), sendEchoRequest(2), other(3) } ACCESS read-write STATUS mandatory DESCRIPTION "The type of echo diagnostic function to initiate. Upon setting this to send EchoRequest (2), an echo request will be initiated and the value will be set to noAction (1)." ::= { nwAtNetDiagOutbound 5 } nwAtNetDiagOutboundATEchoStatus OBJECT-TYPE SYNTAX INTEGER { inactive(1), inProgress(2), timeout(3), success(4) } ACCESS read-write STATUS mandatory DESCRIPTION "The current status of the echo diagnostic." ::= { nwAtNetDiagOutbound 6 } nwAtNetDiagOutboundNBPEntityObject OBJECT-TYPE SYNTAX AtName ACCESS read-write STATUS mandatory DESCRIPTION "The entity object or wildcard object used in the NBP lookup diagnostic." ::= { nwAtNetDiagOutbound 7 } nwAtNetDiagOutboundNBPEntityType OBJECT-TYPE SYNTAX AtName ACCESS read-write STATUS mandatory DESCRIPTION "The entity type or wildcard type used in the NBP lookup diagnostic." ::= { nwAtNetDiagOutbound 8 } nwAtNetDiagOutboundNBPEntityZone OBJECT-TYPE SYNTAX AtName ACCESS read-write STATUS mandatory DESCRIPTION "The entity zone used in the NBP lookup diagnostic." ::= { nwAtNetDiagOutbound 9 } nwAtNetDiagOutboundNBPType OBJECT-TYPE SYNTAX INTEGER { noAction(1), localRequest(2), lookupMcast(3), lookupBcast(4), lookupDirect(5), bcastRequestBcast(6), bcastRequestDirect(7), forwardRequestBcast(8), forwardRequestDirect(9), other(10) } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the type of outbound NBP diagnostic function to initiate. Upon setting this value to any value other than noAction (1) or other (10), the corresponding request will be made and the value will be set to noAction (1)." ::= { nwAtNetDiagOutbound 10 } nwAtNetDiagOutboundNBPStatus OBJECT-TYPE SYNTAX INTEGER { inactive(1), inProgress(2), done(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Indicates the current status of the outbound NBP diagnostic." ::= { nwAtNetDiagOutbound 11 } nwAtNetDiagOutboundRTMPType OBJECT-TYPE SYNTAX INTEGER { noAction(1), sendRequest(2), bcastRequest(3), sendRDRequestSplitHorizon(4), bcastRDRequestSplitHorizon(5), sendRDRequestFullTable(6), bcastRDRequestFullTable(7), other(8) } ACCESS read-write STATUS mandatory DESCRIPTION "The type of outbound RTMP diagnostic function to initiate. Upon setting this value to a value other than noAction(1) or other(8), the corresponding request will be initiated and the value will be set to noAction(1)." ::= { nwAtNetDiagOutbound 12 } nwAtNetDiagOutboundRTMPStatus OBJECT-TYPE SYNTAX INTEGER { inactive(1), inProgress(2), done(3) } ACCESS read-write STATUS mandatory DESCRIPTION "The current status of the outbound RTMP diagnostic." ::= { nwAtNetDiagOutbound 13 } nwAtNetDiagOutboundRTMPNetStart OBJECT-TYPE SYNTAX AtNetworkNumber ACCESS read-write STATUS mandatory DESCRIPTION "The start of the network range from the last successful outbound RTMP request or route data request." ::= { nwAtNetDiagOutbound 14 } nwAtNetDiagOutboundRTMPNetEnd OBJECT-TYPE SYNTAX AtNetworkNumber ACCESS read-write STATUS mandatory DESCRIPTION "The end of the network range from the last successful outbound RTMP request or route data request." ::= { nwAtNetDiagOutbound 15 } nwAtNetDiagOutboundZIPType OBJECT-TYPE SYNTAX INTEGER { noAction(1), sendQuery(2), bcastQuery(3), sendGetZonesList(4), sendGetLocalZones(5), sendGetMyZone(6), sendGetNetInfo(7), bcastGetNetInfo(8), other(9) } ACCESS read-write STATUS mandatory DESCRIPTION "The type of outbound ZIP diagnostic function to initiate. Upon setting this value to a value other than noAction(1) or other(8), the corresponding request will be initiated and the value will be set to noAction(1)." ::= { nwAtNetDiagOutbound 16 } nwAtNetDiagOutboundZIPStatus OBJECT-TYPE SYNTAX INTEGER { inactive(1), queryInProgress(2), atpInProgress(3), gniInProgress(4), done(5) } ACCESS read-write STATUS mandatory DESCRIPTION "The current status of the outbound ZIP diagnostic." ::= { nwAtNetDiagOutbound 17 } nwAtNetDiagOutboundZIPQueryNet OBJECT-TYPE SYNTAX AtNetworkNumber ACCESS read-write STATUS mandatory DESCRIPTION "The start of the network range to send ZIP query for." ::= { nwAtNetDiagOutbound 18 } nwAtNetDiagOutboundZIPQueryZone OBJECT-TYPE SYNTAX AtName ACCESS read-write STATUS mandatory DESCRIPTION "The first zone from the last successful ZIP query." ::= { nwAtNetDiagOutbound 19 } nwAtNetDiagOutboundZIPGetNetInfoZone OBJECT-TYPE SYNTAX AtName ACCESS read-write STATUS mandatory DESCRIPTION "The zone name to be used in a ZIP get-net-info request diagnostic." ::= { nwAtNetDiagOutbound 20 } nwAtNetDiagOutboundZIPGetNetInfoNetStart OBJECT-TYPE SYNTAX AtNetworkNumber ACCESS read-write STATUS mandatory DESCRIPTION "The start of the network range from the last successful ZIP get-net-info request." ::= { nwAtNetDiagOutbound 21 } nwAtNetDiagOutboundZIPGetNetInfoNetEnd OBJECT-TYPE SYNTAX AtNetworkNumber ACCESS read-write STATUS mandatory DESCRIPTION "The end of the network range from the last successful ZIP get-net-info request." ::= { nwAtNetDiagOutbound 22 } nwAtNetDiagOutboundZIPGetNetInfoMulticast OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "The data-link multicast address from the last successful ZIP get-net-info request." ::= { nwAtNetDiagOutbound 23 } nwAtNetDiagOutboundZIPGetNetInfoDefaultZone OBJECT-TYPE SYNTAX AtName ACCESS read-write STATUS mandatory DESCRIPTION "The default zone name from the last successful ZIP get-net-info request." ::= { nwAtNetDiagOutbound 24 } -- AppleTalk Experimental Branch -- The AppleTalk zone table has been placed under the -- experimental branch because it is based on the appletalk -- draft mib and shall be deprecated when the draft mib -- becomes a standard. -- The atportZoneTable stores information about the zones -- associated with each port. The default zone for each -- port is stored in the port's atportZoneDefault variable; -- all other zones for the port are listed in this table. -- If a port only has one zone, it should be stored in the -- port's atportZoneDefault variable, and this table should -- be empty. nwAtportZoneTable OBJECT-TYPE SYNTAX SEQUENCE OF NwAtportZoneEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table of zone information for non-default zones on ports." ::= { nwRtrExperimental 1 } nwAtportZoneEntry OBJECT-TYPE SYNTAX NwAtportZoneEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry of zone information for a port." INDEX { nwAtportZonePort, nwAtportZoneName } ::= { nwAtportZoneTable 1 } NwAtportZoneEntry ::= SEQUENCE { nwAtportZonePort INTEGER, nwAtportZoneName AtName, nwAtportZoneStatus INTEGER } nwAtportZonePort OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "An integer representing the port to which this zone belongs. The port identified by a particular value of this object is the same port as identified by the same value of nwAtportIndex." ::= { nwAtportZoneEntry 1 } nwAtportZoneName OBJECT-TYPE SYNTAX AtName ACCESS read-only STATUS mandatory DESCRIPTION "A zone name configured for the AppleTalk port referred to in the corresponding entry of nwAtportZonePort. When this value is changed in a router, the router must send a zipNotify packet on the associated network." ::= { nwAtportZoneEntry 2 } nwAtportZoneStatus OBJECT-TYPE SYNTAX INTEGER { valid(1), invalid(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The status of this zone entry. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the nwAtportZoneTable. That is, it effectively disassociates the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive from agents tabular information corresponding to entries not currently in use. Proper interpretation of such entries requires examination of the relevant nwAtportZoneStatus object." ::= { nwAtportZoneEntry 3 } -- -- IP Hosts-to-Media Table -- This table serves to supplement the MIB-2 Net-To-Media Table. It -- supports both non-WAN interfaces and logical WAN interfaces and the -- circuits under them. In addition to the ifIndex, AtNetworkNumber, and -- PhysAddress mapping, each address translation includes the framing -- required to converse with the host, the platform's logical port number, -- and the circuit identifier associated with the mapping if applicable. nwAtHostMapTable OBJECT-TYPE SYNTAX SEQUENCE OF NwAtHostMapEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The Ip Address translation table used for mapping an IP address to physical address, framing, port and circuit identifier, if applicable." ::= { nwAtHostsToMedia 1 } nwAtHostMapEntry OBJECT-TYPE SYNTAX NwAtHostMapEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry contains one AtNetworkNumber to 'physical' address equivalence, including a circuit identifier if applicable. Also provided is the framing and port number required to converse with this host." INDEX { nwAtHostMapIfIndex, nwAtHostMapAtAddr } ::= { nwAtHostMapTable 1 } NwAtHostMapEntry ::= SEQUENCE { nwAtHostMapIfIndex INTEGER, nwAtHostMapAtAddr AtDdpNodeAddress, nwAtHostMapPhysAddr PhysAddress, nwAtHostMapType INTEGER, nwAtHostMapCircuitID INTEGER, nwAtHostMapFraming INTEGER, nwAtHostMapPortNumber INTEGER } nwAtHostMapIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This is the primary (major) index into the HostMap table. This number corresponds to the index into the MIB-2 Interfaces Group which describes the IP router port for which the entry exists." ::= { nwAtHostMapEntry 1 } nwAtHostMapAtAddr OBJECT-TYPE SYNTAX AtDdpNodeAddress ACCESS read-only STATUS mandatory DESCRIPTION "The AtDdpNodeAddress corresponding to the media-dependent 'physical' address and circuit identifier (if applic)." ::= { nwAtHostMapEntry 2 } nwAtHostMapPhysAddr OBJECT-TYPE SYNTAX PhysAddress ACCESS read-write STATUS mandatory DESCRIPTION "The media-dependent 'physical' address. The value of this object is 0 for entries indicating native-wan(8) framing." ::= { nwAtHostMapEntry 3 } nwAtHostMapType OBJECT-TYPE SYNTAX INTEGER { other(1), invalid(2), dynamic(3), static(4), inactive(5) } ACCESS read-write STATUS mandatory DESCRIPTION "Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the nwAtHostMapTable. That is, it effectively dissasociates the circuit identified with said entry from the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant nwAtHostMapType object." ::= { nwAtHostMapEntry 4 } nwAtHostMapCircuitID OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The identifier for the virtual circuit present on the interface. On an interface configured for Frame Relay, this number is the DLCI for the IP Address at the end of the circuit. For non-WAN interfaces, the value of this object is zero." ::= { nwAtHostMapEntry 5 } nwAtHostMapFraming OBJECT-TYPE SYNTAX INTEGER { -- valid media types other(1), -- experimental ethernet(2), -- ethernet snap(3), -- enet,fddi,and token ring nativewan(8), -- wan media types encapenet(9), -- wan media types encapenetsnap(11), -- wan media types encapfddisnap(16), -- wan media types canonical(17) -- special, tbd } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the framing type required to converse with the host for which this entry exists." ::= { nwAtHostMapEntry 6 } nwAtHostMapPortNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The unique value for the logical port number. It's value ranges between 1 and a maximum value which is dependent on both the number of interfaces in the system and the number of circuits present on interfaces which are of WAN type." ::= { nwAtHostMapEntry 7 } END