CTRON-PORTMAP-MIB CTRON-PORTMAP-MIB DEFINITIONS ::= BEGIN -- CTRON-PORTMAP-MIB The Cabletron Repeater MIB for Port Mapping. -- ctron-portmap-mib.txt -- Revision: 1.00.01 -- Part Number: -- Date: May 22, 1998 -- Cabletron Systems, Inc. -- 35 Industrial Way, P.O. Box 5005 -- Rochester, NH 03867-0505 -- (603) 332-9400 -- support@ctron.com -- This module provides authoritative definitions for part -- of the naming tree below: -- -- cabletron { enterprises 52 } -- -- This module will be extended, as additional sub-sections -- of this naming tree are defined. -- -- Cabletron Systems reserves the right to make changes in -- specification and other information contained in this document -- without prior notice. The reader should consult Cabletron Systems -- to determine whether any such changes have been made. -- -- In no event shall Cabletron Systems be liable for any incidental, -- indirect, special, or consequential damages whatsoever (including -- but not limited to lost profits) arising out of or related to this -- document or the information contained in it, even if Cabletron -- Systems has been advised of, known, or should have known, the -- possibility of such damages. -- -- Cabletron grants vendors, end-users, and other interested parties -- a non-exclusive license to use this Specification in connection -- with the management of Cabletron products. -- Copyright August 98 Cabletron Systems IMPORTS OBJECT-TYPE FROM RFC-1212 ctPortMap FROM CTRON-MIB-NAMES; portMap OBJECT IDENTIFIER ::= { ctPortMap 1 } portMapTable OBJECT-TYPE SYNTAX SEQUENCE OF PortMapEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table identifies the repeater which the port belongs to." ::= { portMap 1 } portMapEntry OBJECT-TYPE SYNTAX PortMapEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Provides basic mapping and capability for a specific port." INDEX { portMapIndex } ::= { portMapTable 1 } PortMapEntry ::= SEQUENCE { portMapIndex INTEGER, portMapRepeater INTEGER, portMapCapability INTEGER, portMapOperationalMode INTEGER, portMapLastSeenSrcAddr OCTET STRING } portMapIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Returns an index to a port for which the information in this table pertains." ::= { portMapEntry 1 } portMapRepeater OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Gives the repeater number that this port is connected to." ::= { portMapEntry 2 } portMapCapability OBJECT-TYPE SYNTAX INTEGER (0..1023) ACCESS read-only STATUS mandatory DESCRIPTION "This indicates the technology ability of the local hardware. The value of this object is the logical OR of all supported technologies, where each technology is given the values below: other(1) Undefined, or ability not known Auto-Negotiation(2) Auto-Negotiation 10BASE-T(4) 10BASE-T 100BASE-TX(8) 100BASE-TX 1000BASE(16) 1000BASE For example, a port that has the capability of supporting 10BASE-T and 100BASE-TX would have a value of 12 (4 + 8)." ::= { portMapEntry 3 } portMapOperationalMode OBJECT-TYPE SYNTAX INTEGER (0..1023) ACCESS read-write STATUS mandatory DESCRIPTION " This indicates the current operational mode of this port. This value is a logical OR of the current operational mode, where each technology is given the values below: other(1) Undefined, or ability not known Auto-Negotiation(2) Auto-Negotiation 10BASE-T(4) 10BASE-T 100BASE-TX(8) 100BASE-TX 1000BASE(16) 1000BASE For example, a port that has auto-negotiated to a speed of 100BASE-TX would have a value of 10 (2 + 8)." ::= { portMapEntry 4 } portMapLastSeenSrcAddr OBJECT-TYPE SYNTAX OCTET STRING (SIZE(6)) ACCESS read-only STATUS mandatory DESCRIPTION "Returns last source address seen by this repeater port." ::= { portMapEntry 5} END