| mdmIDManufacturerOID |
.1.3.6.1.2.1.38.1.1.2.1.2 |
|
This value is intended to identify the manufacturer, model,
and version of this modem. This may be used to identify the
existance of enterprise-specific functions and behaviours.
|
| mdmIDProductDetails |
.1.3.6.1.2.1.38.1.1.2.1.3 |
|
A textual description of this device, including the
manufacturer's name, modem model name, hardware revision,
firmware revision, and optionally, its serial number. The
exact format of this description is defined by the vendor.
This description may only contain characters from the NVT
ASCII character set.
|
| mdmLineCarrierLossTime |
.1.3.6.1.2.1.38.1.1.3.1.1 |
|
Duration in 10ths of a second the modem waits after loss of
carrier before hanging up. If this value is set to `255',
the modem will not hang up upon loss of carrier. This
allows the modem to distinguish between a momentary lapse in
line quality and a true disconnect and can be useful to tune
the tolerance of the modem to lines of poor quality.
|
| mdmLineState |
.1.3.6.1.2.1.38.1.1.3.1.2 |
|
Allows the inspection and alteration of the state of the
modem. Management commands may change the state to `on-
hook', `busied-out', or `reset' from any state. No other
alterations are permitted from the management protocol.
When this object is set to reset, the modem shall be reset
and the value will change to the modem's new, implementation
dependent state.
|
| mdmLineCapabilitiesID |
.1.3.6.1.2.1.38.1.1.4.1.2 |
|
An identifier for this capability. Standard protocol
capabilities will have identifiers registered in this
document or other companion standards documents.
Proprietary protocol capabilities will be registered by
their respective organization. All capabilities, standard
or vendor-specific, shall be registered in this table.
|
| mdmLineCapabilitiesEnableRequested |
.1.3.6.1.2.1.38.1.1.4.1.3 |
|
The requested configuration of this capability. If this
value is 'disabled(1)', this is a request to disable this
protocol. If this value is 'preferred(3)', this is a
request to enable this protocol, and to prefer it in any
negotiation over other appropriate protocols that have a
value of 'optional(2)'.
|
| mdmLineCapabilitiesEnableGranted |
.1.3.6.1.2.1.38.1.1.4.1.4 |
|
The actual configuration of this capability. The agent
shall attempt to set this as close as possible to the
associated mdmLineCapabilitiesEnableRequested value. The
agent shall make this determination in an implementation-
specific manner that may take into account the configuration
of other capabilities or other considerations. The modem
will choose in an implementation-specific manner between
multiple mutually-exclusive capabilities that each have the
same (non-disabled) value. However, the modem must prefer
all capabilities with a value of 'preferred(3)' over all
capabilities with a value of 'optional(2)'.
In other words, if there are one or more mutually-exclusive
capabilities (e.g. V.32 and V.32bis) that are set to
`preferred', the agent must choose one in an
implementation-specific manner. Otherwise, if there are one
or more mutually-exclusive capabilities that are set to
`optional', the agent must choose one in an implementation-
specific manner.
|
| mdmDTEActionDTROnToOff |
.1.3.6.1.2.1.38.1.1.6.1.1 |
|
Defines the action the modem will take when DTR drops.
If the value is set to ignore(1), the modem takes no action
when DTR drops. Typically, mdmDTEActionDTROffToOn would
also be set to ignore(1) if this object is set to ignore(1).
If the value is escapeToCommandMode(2), the modem remains
connected and enters command mode. If the value is
disconnectCall(3), the current call (if any) is terminated
and the modem will not auto-answer while DTR is off. If the
value is resetModem(4), the current call (if any) is
terminated and the modem is reset.
|
| mdmDTEActionDTROffToOn |
.1.3.6.1.2.1.38.1.1.6.1.2 |
|
Defines the action the modem will take when DTR is raised.
If the value is set to ignore(1), the modem takes no action
when DTR is raised. Typically, mdmDTEActionDTROnToOff would
also be set to ignore(1) if this object is set to ignore(1).
If the value is set to enableDial(2), the modem prepares to
dial an outgoing call. If the value is set to
autoAnswerEnable(3), the modem will be configured to answer
any incoming call. If the value is set to
establishConnection(4), the modem dials an implementation
specific number.
Immediately after any reset or power-on of the modem, if the
DTR is high, the action specified here will be executed.
|
| mdmDTESyncTimingSource |
.1.3.6.1.2.1.38.1.1.6.1.3 |
|
The clock source for synchronous transmissions. If set to
internal(1), the modem is the clock source and sends the
clock signals to the DTE. If set to external(2), the
transmit clock signals are provided by the DTE. If
loopback(3), the modem receiver clock is used for the
transmit clock. If network(4), the clock signals are
supplied by the DCE interface.
If the modem is not in synchronous mode, setting this object
will have no effect on the current operations of the modem.
|
| mdmDTESyncAsyncMode |
.1.3.6.1.2.1.38.1.1.6.1.4 |
|
The operational mode of the modem. If the value is
syncAfterDial(3), the modem will accept commands in
asynchronous mode and change to synchronous mode to pass
data after a dial sequence has been executed.
|
| mdmDTEInactivityTimeout |
.1.3.6.1.2.1.38.1.1.6.1.5 |
|
The amount of idle time in minutes that the modem will wait
before disconnecting a connection. When a call is connected
and no data is transferred (continuous marking condition) on
both circuits 103 and 104 for the specified time, the DCE
disconnects the call. If the value is 0, no idle disconnect
will occur. This function applies to asynchronous dial
operations only and is intended for administrative control
over idle connections.
|
| mdmCCRingsBeforeAnswer |
.1.3.6.1.2.1.38.1.1.7.1.1 |
|
Determines which ring the modem will wait to answer the
phone on. If this value is `0', the modem will not go
offhook and answer a call when a ring signal is detected.
|
| mdmCCCallSetUpFailTimer |
.1.3.6.1.2.1.38.1.1.7.1.2 |
|
This parameter specifies the amount of time, in seconds,
that the modem shall allow between either answering a call
(automatically or manually) or completion of dialing, and
establishment of a connection with the remote modem. If no
connection is established during this time, the modem
disconnects from the line and returns a result code
indicating the cause of the disconnection. In TIA-602, this
is controlled by the value in the S7 register.
|
| mdmCCResultCodeEnable |
.1.3.6.1.2.1.38.1.1.7.1.3 |
|
When disabled, the DCE shall issue no 'result codes' of any
kind to the DTE either in response to unsolicited events
(eg. ring signal), or commands. In TIA-602, this is
controlled by the ATQ command. When numericEnabled, the DCE
shall issue result codes in numeric form. When
verboseEnabled, the DCE shall issue result codes in a
verbose, textual form.
|
| mdmCCEscapeAction |
.1.3.6.1.2.1.38.1.1.7.1.4 |
|
The modem's action upon successfully recognizing the
'escape to command mode' character sequence.
|
| mdmCCCallDuration |
.1.3.6.1.2.1.38.1.1.7.1.5 |
|
Present or last completed connection time in seconds. If
there have been no previous connections, this value should
be -1.
|
| mdmCCConnectionFailReason |
.1.3.6.1.2.1.38.1.1.7.1.6 |
|
Indicates the reason that the last connection or attempt
failed. The meaning of each reason code is explained below.
unknown:
This code means the failure reason is unknown or
there has been no previous call.
other:
This code used when no other code is applicable.
Additional vendor information may be available
elsewhere.
managementCommand:
A management command terminated the call. These
commands include escaping to command mode, initiating
dialing, restoring lines, and disconnecting.
inactivityTimeout:
The call was terminated because it was inactive for
at the minimum duration specified.
mnpIncompatibility:
The modems are unable to resolve MNP protocol
differences.
protocolError:
An error occured in one of protocol in use. Further
information is required to determine in which
protocol the error occurred, and the exact nature of
the error.
powerLoss:
The modem lost power and disconnected the call.
equipmentFailure:
The modem equipment failed.
dtrDrop:
DTR has been turned off while the modem is to
disconnect on DTR drop. (Ref: V.58 cct108TurnedOff)
noDialTone:
If the modem is to monitor for call progress tones,
but the modem has failed to detect dial tone while
attempting to dial a number.
lineBusy:
Busy signal is detected while busy signal detection
is enabled, or while the 'W' or '@' dial modifier is
used. (Ref: V.58 engagedTone)
noAnswer:
The call was not answered.
voiceDetected:
A voice was detected on the call.
carrierLost:
Indicates that the modem has disconnected due to
detection of loss of carrier. In TIA-602, the S10
register determines the time that loss of carrier
must be detected before the modem disconnects.
trainingFailed:
Indicates that the modems did not successfully train
and reach data mode on the previous connection.
faxDetected:
A fax was detected on the call.
|
| mdmCCStoredDialString |
.1.3.6.1.2.1.38.1.1.8.1.2 |
|
A dial string stored in the modem.
|
| mdmECErrorControlUsed |
.1.3.6.1.2.1.38.1.1.9.1.1 |
|
Indicates the error control method used during the current
or previous call. This shall be one of the values for error
control protocols registered in the capabilities table for
this modem. If no error control protocol is in use, this
object shall have the value '{0 0}'.
|
| mdmDCCompressionTypeUsed |
.1.3.6.1.2.1.38.1.1.10.1.1 |
|
Indicates the data compression method used during the
current or previous call. This shall be one of the values
for compression protocols registered in the capabilities
table for this modem. If no compression protocol is in use,
this object shall have the value '{0 0}'.
|
| mdmSCCurrentLineReceiveRate |
.1.3.6.1.2.1.38.1.1.11.1.2 |
|
The current link receive rate of a connection, or the last
link receive rate of the last connection in bits per
second.
|
| mdmSCCurrentLineTransmitRate |
.1.3.6.1.2.1.38.1.1.11.1.1 |
|
The current link transmit rate of a connection, or the last
link transmit rate of the last connection in bits per
second.
|
| mdmSCInitialLineReceiveRate |
.1.3.6.1.2.1.38.1.1.11.1.4 |
|
The initial link receive rate of the current connection, or
the initial link receive rate of the last connection in bits
per second.
|
| mdmSCInitialLineTransmitRate |
.1.3.6.1.2.1.38.1.1.11.1.3 |
|
The initial link transmit rate of the current connection,
or the initial link transmit rate of the last connection in
bits per second.
|
| mdmSCModulationSchemeUsed |
.1.3.6.1.2.1.38.1.1.11.1.5 |
|
The modulation scheme of the current or previous call.
This shall be one of the values for modulation protocols
registered in the capabilities table for this modem.
|
| mdmStatsRingNoAnswers |
.1.3.6.1.2.1.38.1.1.12.1.1 |
|
The number of events in which ringing was detected but the
call was not answered.
|
| mdmStatsIncomingConnectionFailures |
.1.3.6.1.2.1.38.1.1.12.1.2 |
|
The number of incoming connection requests that this modem
answered in which it could not train with the other DCE.
|
| mdmStatsIncomingConnectionCompletions |
.1.3.6.1.2.1.38.1.1.12.1.3 |
|
The number of incoming connection requests that this modem
answered and successfully trained with the other DCE.
|
| mdmStatsFailedDialAttempts |
.1.3.6.1.2.1.38.1.1.12.1.4 |
|
The number of call attempts that failed because the modem
didn't go off hook, or there was no dialtone.
|
| mdmStatsOutgoingConnectionFailures |
.1.3.6.1.2.1.38.1.1.12.1.5 |
|
The number of outgoing calls from this modem which
sucessfully went off hook and dialed, in which it could not
train with the other DCE.
|
| mdmStatsOutgoingConnectionCompletions |
.1.3.6.1.2.1.38.1.1.12.1.6 |
|
The number of outgoing calls from this modem which resulted
in successfully training with the other DCE.
|
| mdmStatsRetrains |
.1.3.6.1.2.1.38.1.1.12.1.7 |
|
The number of retrains experienced on connections on this
line.
|
| mdmStats2400OrLessConnections |
.1.3.6.1.2.1.38.1.1.12.1.8 |
|
The number of connections initially established at a
modulation speed of 2400 bits per second or less.
|
| mdmStats2400To14400Connections |
.1.3.6.1.2.1.38.1.1.12.1.9 |
|
The number of connections initially established at a
modulation speed of greater than 2400 bits per second and
less than 14400 bits per second.
|
| mdmStatsGreaterThan14400Connections |
.1.3.6.1.2.1.38.1.1.12.1.10 |
|
The number of connections initially established at a
modulation speed of greater than 14400 bits per second.
|
| mdmStatsErrorControlledConnections |
.1.3.6.1.2.1.38.1.1.12.1.11 |
|
The number of established connections using an error
control protocol.
|
| mdmStatsCompressedConnections |
.1.3.6.1.2.1.38.1.1.12.1.12 |
|
The number of established connections using a compression
protocol.
|
| mdmStatsCompressionEfficiency |
.1.3.6.1.2.1.38.1.1.12.1.13 |
|
The number of bytes transferred into the compression
encoder divided by the number of bytes transferred out of
the encoder, multiplied by 100 for either the current or
last call. If a data compression protocol is not in use,
this value shall be `100'.
|
| mdmStatsSentOctets |
.1.3.6.1.2.1.38.1.1.12.1.14 |
|
The number of octets presented to the modem by the DTE.
|
| mdmStatsReceivedOctets |
.1.3.6.1.2.1.38.1.1.12.1.15 |
|
The number of octets presented to the DTE by the modem.
|
| mdmStatsSentDataFrames |
.1.3.6.1.2.1.38.1.1.12.1.16 |
|
The number of data frames sent on the line interface. If
there is no frame-oriented protocol in use on the line
interface, this counter shall not increment.
|
| mdmStatsReceivedDataFrames |
.1.3.6.1.2.1.38.1.1.12.1.17 |
|
The number of data frames received on the line interface.
If there is no frame-oriented protocol in use on the line
interface, this counter shall not increment.
|
| mdmStatsResentFrames |
.1.3.6.1.2.1.38.1.1.12.1.18 |
|
The number of times this modem retransmits frames on the
line interface. If there is no frame-oriented protocol in
use on the line interface, this counter shall not
increment.
|
| mdmStatsErrorFrames |
.1.3.6.1.2.1.38.1.1.12.1.19 |
|
The number of block errors received on the link. If there
is no frame-oriented protocol in use on the line interface,
this counter shall not increment.
|
| mdmIndex |
.1.3.6.1.2.1.38.1.1.2.1.1 |
|
A unique number for each modem that ranges from 1 to
mdmNumber. The value must remain constant at least from one
re-initialization of the network management agent to the
next.
|
| mdmLineCapabilitiesIndex |
.1.3.6.1.2.1.38.1.1.4.1.1 |
|
A unique index for this capabilities entry.
|
| mdmCCStoredDialStringIndex |
.1.3.6.1.2.1.38.1.1.8.1.1 |
|
The unique index of a particular dial string.
|
