Wellfleet-DSUCSU-MIB -- This file is the MIB file for a DSUCSU. -- This file, and the associated dsucsu.cdl file, -- were created to manage the internal DSUCSU for NEPTUNE. -- Last Modified 12/19/96 PCK Wellfleet-DSUCSU-MIB DEFINITIONS ::= BEGIN IMPORTS Counter FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212 DisplayString FROM RFC1213-MIB TRAP-TYPE FROM RFC-1215 wfDsuCsuGroup FROM Wellfleet-COMMON-MIB; wfDsuCsuIfTable OBJECT-TYPE SYNTAX SEQUENCE OF WfDsuCsuIfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "DSU CSU line record." ::= { wfDsuCsuGroup 1 } wfDsuCsuIfEntry OBJECT-TYPE SYNTAX WfDsuCsuIfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the DSU CSU IF table" INDEX { wfDsuCsuIfSlot, wfDsuCsuIfConnector } ::= { wfDsuCsuIfTable 1 } WfDsuCsuIfEntry ::= SEQUENCE { wfDsuCsuIfDelete INTEGER, wfDsuCsuIfSlot INTEGER, wfDsuCsuIfConnector INTEGER, wfDsuCsuSoftRev DisplayString, wfDsuCsuHardRev DisplayString, wfDsuCsuOpMode INTEGER, wfDsuCsuTxClkSelect INTEGER, wfDsuCsuUnitReset INTEGER, wfDsuCsu64KTxMonitor INTEGER, wfDsuCsuOpState INTEGER, wfDsuCsuServiceStatus INTEGER, wfDsuCsuV54Lpbk INTEGER, wfDsuCsuV54Timer INTEGER, wfDsuCsuV54Errors Counter, wfDsuCsuCqmsLaWindow INTEGER, wfDsuCsuCqmsLaErrors Counter, wfDsuCsuCqmsLaPollRate INTEGER, wfDsuCsuCqmsReset INTEGER, wfDsuCsuOOSErrors Counter, wfDsuCsuFrameErrors Counter, wfDsuCsuLOLErrors Counter, wfDsuCsuInitState INTEGER } wfDsuCsuIfDelete OBJECT-TYPE SYNTAX INTEGER { created(1), deleted(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Create/Delete parameter" DEFVAL { created } ::= { wfDsuCsuIfEntry 1 } wfDsuCsuIfSlot OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Instance ID Slot, filled in by driver" ::= { wfDsuCsuIfEntry 2} wfDsuCsuIfConnector OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Instance ID Connector, filled in by the driver." ::= { wfDsuCsuIfEntry 3 } wfDsuCsuSoftRev OBJECT-TYPE SYNTAX DisplayString (SIZE (0..10)) ACCESS read-only STATUS mandatory DESCRIPTION "Displays the Software Revision of the DSU CSU card." ::= { wfDsuCsuIfEntry 4 } wfDsuCsuHardRev OBJECT-TYPE SYNTAX DisplayString (SIZE (0..10)) ACCESS read-only STATUS mandatory DESCRIPTION "Displays the Hardware Revision of the DSU CSU card." ::= { wfDsuCsuIfEntry 5 } wfDsuCsuOpMode OBJECT-TYPE SYNTAX INTEGER { dds156kbps(1), cc64kbps(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Identifies the type of telco service that the DSU CSU is connected to. Opmode should be set to dds1-56kbps (1) when connected to a DDS1 56 Kbps line. Opmode should be set to cc-64kbps (2) when connected to a Clear Channel 64Kbps line." DEFVAL { dds156kbps } ::= { wfDsuCsuIfEntry 6 } wfDsuCsuTxClkSelect OBJECT-TYPE SYNTAX INTEGER { slave(1), master(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Default timing, or clock, source for transmiting data to the network. There must be only one source on a DDS line. Timing should always be slave (1) when connected to a network. Timing should be set to master (2) on either end of a private-wire configuration, with the other end being set to slave (1)." DEFVAL { slave } ::= { wfDsuCsuIfEntry 7 } wfDsuCsuUnitReset OBJECT-TYPE SYNTAX INTEGER { resetUnit(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Enables the operator to remotely reset the unit. Using this command will cause the unit to terminate all its connections and drop data." ::= { wfDsuCsuIfEntry 8 } wfDsuCsu64KTxMonitor OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This signal is used in 64K Clear Channel mode to suppress customer data in the event that the data duplicates a network control code. A setting of enabled(1) suppresses customer data. A setting of disabled(2) allows all customer data through, which could potentially put the other end into a loop if the data duplicates a network control code." DEFVAL { disabled } ::= { wfDsuCsuIfEntry 9 } wfDsuCsuOpState OBJECT-TYPE SYNTAX INTEGER { normal(1), localLpbk(2), digitalLpbk(3), remDigitalLpbk(4), telcoLpbk(5), remDigLpbkWPattern(6), localAnlgLpbkWPattern(7), pattern2047Gen(8) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the current operating state of the DSU CSU card." DEFVAL { normal } ::= { wfDsuCsuIfEntry 10 } wfDsuCsuServiceStatus OBJECT-TYPE SYNTAX INTEGER { inService(1), outOfService(2), frameError(3), lossOfLine(5), telcoLpbk(6) } ACCESS read-only STATUS mandatory DESCRIPTION "The Current status of the physical interface. Your network carrier can send Out-of-Service or Maintenance Mode codes." DEFVAL { inService } ::= { wfDsuCsuIfEntry 11 } wfDsuCsuV54Lpbk OBJECT-TYPE SYNTAX INTEGER { noLoop(1), localAnlgLpbk(2), localDigLpbk(3), remDigLpbk(4), remDigLpbkWPattern(5), localAnlgLpbkWPattern(6), pattern2047Gen(7) } ACCESS read-write STATUS mandatory DESCRIPTION "Enables the operator to control, and examine the state of, V.54 loopbacks within the DSU CSU." DEFVAL { noLoop } ::= { wfDsuCsuIfEntry 12 } wfDsuCsuV54Timer OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "Duration in seconds that a test specified in wfDsuCsuTestLpbk is to execute." DEFVAL { 0 } ::= { wfDsuCsuIfEntry 13 } wfDsuCsuV54Errors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the number of errors reported during the last loopback test. This count will only be updated for loopbacks with test pattern." ::= { wfDsuCsuIfEntry 14 } wfDsuCsuCqmsLaWindow OBJECT-TYPE SYNTAX INTEGER (1..15) ACCESS read-write STATUS mandatory DESCRIPTION "Indicates the number of minutes within the window in which the availability of the line (network) is to be calculated. The availability of the line is an indication of the percentage of time the line has been in service. It is calculated as follows: (((wfDsuCsuCqmsLaWindow*60) - (wfDsuCsuCqmsLaErrCnt*wfDsuCsuCqmsLaPollRate))/ wfDsuCsuCqmsLaWindow*60)" DEFVAL { 15 } ::= { wfDsuCsuIfEntry 15 } wfDsuCsuCqmsLaErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of seconds that the line was not in service in the last window of size wfDsuCsuCqmsLaWindow." ::= { wfDsuCsuIfEntry 16 } wfDsuCsuCqmsLaPollRate OBJECT-TYPE SYNTAX INTEGER (1..60) ACCESS read-write STATUS mandatory DESCRIPTION "Indicates the number of seconds between polls for line status from the DsuCsu. A value of 1 forces polling every second. A value of 60 forces polling every minute." DEFVAL { 1 } ::= { wfDsuCsuIfEntry 17 } wfDsuCsuCqmsReset OBJECT-TYPE SYNTAX INTEGER { resetCqms(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Resets the CQMS counters to their default values. For Line Availability, wfDsuCsuCqmsLaErrCnt is reset." ::= { wfDsuCsuIfEntry 18 } wfDsuCsuOOSErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of seconds in which Out of Service control codes were received from the Telco. The counter is incremented whenever a sample within a second indicated the unit received an out of service control code." ::= { wfDsuCsuIfEntry 19 } wfDsuCsuFrameErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of seconds in which the unit was out of frame with the Telco. This is only applicable in 64K mode. The counter is incremented whenever a sample within a second indicated the unit was out of frame." ::= { wfDsuCsuIfEntry 20 } wfDsuCsuLOLErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of seconds in which the unit has detected that no signal is present on the line, and/or no line is present." ::= { wfDsuCsuIfEntry 21 } wfDsuCsuInitState OBJECT-TYPE SYNTAX INTEGER { startup(1), init(2), monitor(3), loopback(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Indictes the state of the DSU/CSU initialization sequence. The state will indicate if the DSU/CSU has been initialized and is in the *monitor* state polling the card for line condition, or in the *loopback state running a user-initiated loopback" ::= {wfDsuCsuIfEntry 22 } wfDsuCsuIfTrap TRAP-TYPE ENTERPRISE wfDsuCsuGroup VARIABLES { wfDsuCsuServiceStatus } DESCRIPTION "Indicates a change in the status of the line. The value returned in the trap will indicate the current state as defined in wfDsuCsuServiceStatus." ::= 1 END -- Wellfleet-DSUCSU-MIB