ActiveXperts Network Monitor 2019##AdminFavorites

CISCO-VOICE-IF-MIB.mib object view, vendor Cisco

Introduction

Most network devices and programs ship with so-called MIB files to describe the parameters and meanings (i.e.: friendly names) which are available for monitoring via SNMP.
ActiveXperts Network Monitor 2019 can import vendor-specific MIB files, so it can be used to monitor specific OID's (Object Identifiers). This way, you can monitor your devices, computers, etc. by selecting your relevant OID's by name.

ActiveXperts Network Monitor 2019 can import MIB file CISCO-VOICE-IF-MIB and use it to monitor vendor specific OID's.

CISCO-VOICE-IF-MIB file content

Object view of CISCO-VOICE-IF-MIB:

Scalar Object
cvIfCfgEntry .1.3.6.1.4.1.9.9.64.1.1.1.1
An entry in the configuration table for each voice analog interface or voice feature associated ISDN signalling channel. The entry is automatically created when a voice analog interface hardware is found or ISDN signalling channel is configured and the ISDN associated voice support hardware is detected by the managed system. For the ISDN signalling channel associated entry, the entry is deleted after ISDN signalling channel is removed.
Tabular Object
cvIfCfgNoiseRegEnable .1.3.6.1.4.1.9.9.64.1.1.1.1.1
The object indicates whether or not the background noise should be played to fill silence gaps if VAD is activated. The default value of this object is enabled.
cvIfCfgNonLinearProcEnable .1.3.6.1.4.1.9.9.64.1.1.1.1.2
The object indicates whether or not the Nonlinear Processing is enabled for the interface. The default value of this object is enabled.
cvIfCfgMusicOnHoldThreshold .1.3.6.1.4.1.9.9.64.1.1.1.1.3
The object specifies the Music On Hold Threshold for the interface. The default value of this object is -38 dBm.
cvIfCfgInGain .1.3.6.1.4.1.9.9.64.1.1.1.1.4
This object contains the amount of gain inserted at the receiver side of the interface. The input gain settings only define a gain/loss relative to the 0 dB setting. The absolute loss at the 0 dB setting could be implementation dependent based on the desired network loss plan. The default value of this object is 0 dB (decibel).
cvIfCfgOutAttn .1.3.6.1.4.1.9.9.64.1.1.1.1.5
This object contains the amount of attenuation inserted at the transmit side of the interface. The output attenuation settings only define a loss relative to the 0 dB setting. The absolute loss at the 0 dB setting could be implementation dependent based on the desired network loss plan. The default value of this object is 0 dB (decibel).
cvIfCfgEchoCancelEnable .1.3.6.1.4.1.9.9.64.1.1.1.1.6
The object specifies whether or not the Echo Cancellation is enabled for the interface. The default value of this object is enabled.
cvIfCfgEchoCancelCoverage .1.3.6.1.4.1.9.9.64.1.1.1.1.7
The object specifies the Echo Canceller coverage for the interface. This object is valid if the cvIfCfgEchoCancelEnable object is 'true'. echoCanceller16ms - 16 milliseconds echo canceller coverage. echoCanceller24ms - 24 milliseconds echo canceller coverage. echoCanceller32ms - 32 milliseconds echo canceller coverage. The default value of this object is echoCanceller16ms.
cvIfCfgConnectionMode .1.3.6.1.4.1.9.9.64.1.1.1.1.8
The object indicates the connection mode of the interface. normal - the interface acts normally to handle incoming and outgoing call. trunk - the interface acts in trunking mode. trunking mode causes two interfaces (on either the same or different routers) to be always conferenced together, and for telephony signaling to be passed transparently through the VoIP system rather than trapped and interpreted by the session application on the router(s). plar - the interface acts in PLAR (private line automatic ringdown) mode. PLAR is handled by associating a peer directly with an interface such that when the interface goes off-hook, that peer is used to setup the second call leg and conference them together without the caller having to dial any digits.
cvIfCfgConnectionNumber .1.3.6.1.4.1.9.9.64.1.1.1.1.9
This is the E.164 phone number that is used to establish connection with trunking mode or PLAR mode. If the cvIfCfgConnectionMode is 'normal', then this object will be a zero length string.
cvIfCfgInitialDigitTimeOut .1.3.6.1.4.1.9.9.64.1.1.1.1.10
This is the initial digit timeout that indicates the amount of time the managed system waits for an initial input digit from the caller. The timer is activated when the call is accepted and is deactivated upon digit input. If the timer expires, the caller is signaled through the appropriate tone and the call is abandoned. The value of zero disables the timer. The default value of this object is 10 seconds.
cvIfCfgInterDigitTimeOut .1.3.6.1.4.1.9.9.64.1.1.1.1.11
This is the inter-digit timeout that indicates the amount of time the managed system waits for a subsequent input digit from the caller. The timer is started upon receipt of an input digit and restarted as each digit is received until the destination address is identified. If the timer expires and no destination address is identified, the caller is signaled through the appropriate tone and the call is abandoned. The value of zero disables the timer. The default value of this object is 10 seconds.
cvIfCfgRegionalTone .1.3.6.1.4.1.9.9.64.1.1.1.1.12
This object contains the country specific setting for the tone, ring, cadence parameters to be used by this interface.
Table
cvIfCfgTable .1.3.6.1.4.1.9.9.64.1.1.1
The Voice Common Configuration Table. It contains information about the voice related configuration parameters for both analog and digital telephony interfaces.
Object Identifier
ciscoVoiceInterfaceMIB .1.3.6.1.4.1.9.9.64
Common Voice Interface MIB module. The MIB module manages the common voice related parameters for both voice analog and ISDN interfaces.
cvIfObjects .1.3.6.1.4.1.9.9.64.1
cvIfCfgObjects .1.3.6.1.4.1.9.9.64.1.1
cvIfConformance .1.3.6.1.4.1.9.9.64.2
cvIfCompliances .1.3.6.1.4.1.9.9.64.2.1
cvIfGroups .1.3.6.1.4.1.9.9.64.2.2
Group
cvIfGroup .1.3.6.1.4.1.9.9.64.2.2.1
A collection of objects providing the Common Voice parameter related configuration for both analog and digital voice interfaces.
cvIfConnectionGroup .1.3.6.1.4.1.9.9.64.2.2.2
A collection of objects providing trunking or PLAR (private line automatic ringdown) related configuration for voice analog interfaces.