| cds3LineType |
.1.3.6.1.4.1.9.9.132.1.1.1.1.1 |
|
This variable indicates the variety of DS3 C-bit
or E3 application implementing this interface.
The type of interface affects the interpretation
of the usage and error statistics. The rate of DS3
is 44.736 Mbps and E3 is 34.368 Mbps.
The values, in sequence, describe:
Following values are applicable to DS3 interfaces only.
ds3cbitadm : Indicates C-BIT ADM mode
ds3cbitplcp : Indicates C-BIT PLCP mode
ds3m23adm : Indicates M23 ADM mode
ds3m23plcp : Indicates M23 PLCP mode
dsx3M23 : Refer ANSI T1.107-1988 [9]
dsx3SYNTRAN : Refer ANSI T1.107-1988 [9]
dsx3CbitParity : Refer ANSI T1.107-1988 [9]
dsx3ClearChannel : Refer ANSI T1.107-1988 [9]
ds3cbitfrmronly : Indicates C-BIT FRAMER-ONLY mode
ds3m23frmronly : Indicates M23 FRAMER-ONLY mode
Following values are applicable to E3 interfaces only.
e3g832adm : Indicates G.832 ADM mode
e3g751adm : Indicates G.751 ADM mode
e3g751plcp : Indicates G.751 PLCP mode
e3Framed : Refer CCITT G.751 [12]
e3Plcp : Refer ETSI T/NA(91)19 [14]
e3g832frmronly : Indicates G.832 FRAMER-ONLY mode
e3g751frmronly : Indicates G.751 FRAMER-ONLY mode.
|
| cds3LineAIScBitsCheck |
.1.3.6.1.4.1.9.9.132.1.1.1.1.2 |
|
When check(1) is set, then Alarm Indication Signal (AIS)
is declared when '1010...'b is found and C-Bits are all zero.
When ignore(2) is set, an AIS condition is declared when the
'1010...'b is detected irrespective of the state of the C-Bits.
Does not apply to the E3 interface.
The value notApplicable(3) is used in case of the interfaces
where this object is not applicable. The notApplicable(3)
is not allowed in write operation.
|
| cds3LineRcvFEACValidation |
.1.3.6.1.4.1.9.9.132.1.1.1.1.3 |
|
This entry specifies the FEAC (Far End Alarm and Control) code
validation criteria. If 'fEACCodes4Of5' is specified, then a valid
FEAC code is declared if 4 of 5 codes match. When 'fEACCodes8Of10'
is specified, then a valid FEAC code is declared when 8 of 10 codes
match. If disable(3) is specified, then FEAC code generation
and detection is disabled.
Does not apply to the E3 interface.
|
| cds3LineOOFCriteria |
.1.3.6.1.4.1.9.9.132.1.1.1.1.4 |
|
This entry specifies the out of frame(OOF) decision criteria.
If 'bits3Of8' is specified then an OOF condition is declared if
at least 3 of 8 framing bits are in error. When 'bits3Of16' is
specified then OOF is declared if 3 of 16 framing bits are found
to be in error.
OOF is declared when errors are detected in the framing
octets for four consecutive frames.
This object does not apply to E3 interface.
The value notApplicable(3) is used in case of the interfaces
where this object is not applicable. The notApplicable(3)
is not allowed in write operation.
|
| cds3TraceToTransmit |
.1.3.6.1.4.1.9.9.132.1.1.1.1.5 |
|
Transmitted G.832 Trail Trace string.
|
| cds3TraceToExpect |
.1.3.6.1.4.1.9.9.132.1.1.1.1.6 |
|
G.832 Trail Trace string that is expected to be received from
the other end.
|
| cds3TraceAlarm |
.1.3.6.1.4.1.9.9.132.1.1.1.1.7 |
|
The value of this object is set to traceFailure(2) when
DS3 line receives a trace does not match the
'cds3TraceToExpect'.
|
| cds3InternalEqualizer |
.1.3.6.1.4.1.9.9.132.1.1.1.1.8 |
|
This variable indicates whether the internal equalizer is being
used or bypassed. Set this value depending on the line equipment
to which the receiver is attached.
Possible values are :
use(1) : Use the internal equalizer
byPass(2) : bypass internal equalizer(use external equalizer).
This option allows easy interfacing of the
device into systems already utilizing the external
equalizers.
|
| cds3NearEndLineLoopbackStatus |
.1.3.6.1.4.1.9.9.132.1.1.1.1.9 |
|
Indicates the loopback status of the near end DS1 on this
DS3 when loopback request is indicated.
Following table lists the mapping of Bit position to
DS1 or DS3 lines and the value.
Bit Position Line number value
----------------------------------------
0 DS3 Line 0 = no loop(loop down)
1 = loop(loop up)
1 DS1 line 1 0 = loop down
1 = loop up
2 DS1 line 2 0 = loop down
1 = loop up
3 DS1 line 3 0 = loop down
1 = loop up
...
...
28 DS1 line 28 0 = loop down
1 = loop up
29 all DS1 lines 0 = loop up
1 = loop down
|
| cds3FarEndLineLoopbackStatus |
.1.3.6.1.4.1.9.9.132.1.1.1.1.10 |
|
Indicates the loopback status of the far end DS3,DS1
when remote DS1 loopback request is initiated.
The remote DS1 loopback is initiated by setting dsx3SendCode
object to dsx3SendDS1LoopCode(5).
For unchannelized DS3 applications DS1s are unassigned.
Following table lists the mapping of Bit position to
DS1 or DS3 lines and the value.
Bit Position Line number value
----------------------------------------
0 DS3 Line 0 = line loopback activate
1 = line loopback deactivate
1 DS1 line 1 0 = loop down
1 = loop up
2 DS1 line 2 0 = loop down
1 = loop up
3 DS1 line 3 0 = loop down
1 = loop up
...
...
28 DS1 line 29 0 = loop down
1 = loop up
29 all DS1 lines 0 = loop down
1 = loop up
|
| cds3NEAlarmUpCount |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.1 |
|
This parameter specifies the increment to the Near End alarm
integration counters. The local alarms are LOS and LOF. The
Default value is 6 and the integration counter is incremented by
this value every 10 ms while the alarm persists. The
counter is decremented by the value of 'cds3NEAlarmDownCount'
while there is no alarm (the counter does not decrement below
zero). When the integration counter exceeds 'cds3NEAlarmThreshold'
an Alarm of the severity specified for the particular Near End
alarm is declared.
|
| cds3NEAlarmDownCount |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.2 |
|
This parameter specifies the decrement to the Near End alarm
integration counters. The alarms are LOS and LOF. The
Default value is 1 and the integration counter is decremented by
this value every 10 ms while no alarm persists. The
counter is incremented by the value of cds3NEAlarmUpCount
while there is no alarm (the counter does not decrement below
zero). When the integration counter reaches zero any Alarm
previously declared is removed.
|
| cds3NEAlarmThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.3 |
|
The value set in this object determines the value that
the alarm integration counter must reach for an near end
alarm to be declared. If the up count is 6, and the threshold 150,
an Alarm is integrated in 2.5 seconds. If the down count is 1,
then alarm will be cleared in 15 seconds.
|
| cds3FEAlarmUpCount |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.4 |
|
This parameter specifies the increment to the Far End alarm
integration counters. The alarms are Remote Alarm Indication
(RAI) and Alarm Indication Signal(AIS). The integration counter is
incremented by this value every 10 ms while the alarm persists. The
counter is decremented by this value while there is no alarm
(the counter does not decrement below zero).
When the integration counter exceeds cds3FEAlarmThreshold
an Alarm of the severity specified for the particular far end
alarm is declared.
|
| cds3FEAlarmDownCount |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.5 |
|
This parameter specifies the decrement to the Far End alarm
integration counters. The alarms are Alarm Indication Signal
(AIS) and Remote Alarm Indication (RAI). The integration counter
is decremented by this value every 10 ms (till zero), while no
alarm persists. The counter is incremented by this value while
there is no alarm. When the integration counter decrements to
zero any previously declared Alarm is removed.
|
| cds3FEAlarmThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.6 |
|
The value set in this object determines the value that
the alarm integration counter must reach for an far end
Alarm to be declared. If the up count is 6, the down count
is 1 and the threshold 150, an Alarm is integrated in
2.5 sec and removed in 15 seconds.
|
| cds3StatisticalAlarmSeverity |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.7 |
|
This variable is used to setup the severity of any of the
Statistical alarms. So when a Statistical Counter exceeds its
specified threshold the system will send the alarm with
appropriate severity. A value of none(3) indicates that no
alarm will be raised.
|
| cds3LCV15MinThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.8 |
|
The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.
|
| cds3LCV24HrThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.9 |
|
The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval.
|
| cds3LES15MinThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.10 |
|
The value set in this object determines the value
which when exceeded in a 15 minute window causes
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.
|
| cds3LES24HrThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.11 |
|
The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval.
|
| cds3PCV15MinThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.12 |
|
The value set in this object determines the value which when
exceeded in a 15 minute window causes a statistical alarm to be
declared.
Not for E3.
|
| cds3PCV24HrThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.13 |
|
The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval.
Not for E3.
|
| cds3PES15MinThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.14 |
|
The value set in this object determines the value which when exceeded
in a 15 minute window causes a statistical alarm to be declared.
Not for E3.
|
| cds3PES24HrThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.15 |
|
The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval.
Not for E3.
|
| cds3PSES15MinThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.16 |
|
The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.
Not for E3.
|
| cds3PSES24HrThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.17 |
|
The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval.
Not for E3.
|
| cds3SEFS15MinThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.18 |
|
The value set in this object determines the value which when exceeded
in a 15 minute window causes a statistical alarm to be declared.
|
| cds3SEFS24HrThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.19 |
|
The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval
|
| cds3UAS15MinThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.20 |
|
The value set in this object determines the value which when
exceeded in a 15 minute window causes a statistical alarm to
be declared.
|
| cds3UAS24HrThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.21 |
|
The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval
|
| cds3CCV15MinThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.22 |
|
The value set in this object determines the value which when exceeded
in a 15 minute window causes a statistical alarm to be declared.
Not for E3.
|
| cds3CCV24HrThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.23 |
|
The value set in this object determines the value which when exceeded
in a sliding 24 hour window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the preceding 24 hour
interval.
Not for E3.
|
| cds3CES15MinThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.24 |
|
The value set in this object determines the value which when exceeded
in a 15 minute window causes a statistical alarm to be declared.
Not for E3.
|
| cds3CES24HrThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.25 |
|
The value set in this object determines the value which when exceeded
in a sliding 24 hour window causes a statistical alarm to be declared.
Not for E3.
|
| cds3CSES15MinThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.26 |
|
The value set in this object determines the value which when exceeded
in a 15 minute window causes a statistical alarm to be declared.
Not for E3.
|
| cds3CSES24HrThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.27 |
|
The value set in this object determines the value which when
exceeded in a sliding 24 hour window causes a statistical
alarm to be declared. Not for E3.
|
| cds3LSES15MinThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.28 |
|
Used to set the 15 minute threshold for LSES(Line Severely Errored
Seconds).
The value set in this object determines the value which when
exceeded in a 15 minute window causes a statistical alarm to be
declared.
|
| cds3LSES24HrThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.29 |
|
The value set in this object determines the value which when
exceeded in a sliding 24 hour window causes a statistical alarm
to be declared.
|
| cds3LineStatisticalAlarmState |
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.30 |
|
This is a bitmap of the DS3 Line Statistical alarms. It is
represented as a sum where value 2^(N-1) is added to the
sum if threshold corresponding to bit N is exceeded. Zero
indicates no alarms.
Itemized below are the individual alarm bits:
BitPosition Alarm
----------- -----
1 PES current 15 minute threshold exceeded
2 PES 24 hour threshold exceeded
3 PSES current 15 minute threshold exceeded
4 PSES 24 hour threshold exceeded
5 SEFS current 15 minute threshold exceeded
6 SEFS 24 hour threshold exceeded
7 UAS current 15 minute threshold exceeded
8 UAS 24 hour threshold exceeded
9 LCV current 15 minute threshold exceeded
10 LCV 24 hour threshold exceeded
11 PCV current 15 minute threshold exceeded
12 PCV 24 hour threshold exceeded
13 LES current 15 minute threshold exceeded
14 LES 24 hour threshold exceeded
15 CCV current 15 minute threshold exceeded
16 CCV 24 hour threshold exceeded
17 CES current 15 minute threshold exceeded
18 CES 24 hour threshold exceeded
19 CSES current 15 minute threshold exceeded
20 CSES 24 hour threshold exceeded
21 LSES current 15 minute threshold exceeded
22 LSES 24 hour threshold exceeded
|
| cds3RcvLOSCount |
.1.3.6.1.4.1.9.9.132.1.3.1.1.1 |
|
The number of times Loss of Signal was detected
with or without integrating to LOS alarm.
|
| cds3RcvOOFCount |
.1.3.6.1.4.1.9.9.132.1.3.1.1.2 |
|
The number of times Out of Frame was detected with or without
integrating to OOF alarm.
|
| cds3RAICount |
.1.3.6.1.4.1.9.9.132.1.3.1.1.3 |
|
The number of timesRemote Alarm Indication was detected with
or without integrating to RAI alarm.
|
| cds3CCVCount |
.1.3.6.1.4.1.9.9.132.1.3.1.1.4 |
|
The counter associated with the number of C-Bit Coding
Violations encountered by a T3/E3 interface.
|
| cds3FECount |
.1.3.6.1.4.1.9.9.132.1.3.1.1.5 |
|
The number of Framing Errors encountered by a T3/E3 interface.
|
| cds3EXZSCount |
.1.3.6.1.4.1.9.9.132.1.3.1.1.6 |
|
The number of Excessive Zeros(EXZ) by a T3/E3 interface.
An EXZ is the occurrence of any string of zeros having length
equal to or greater than 3 for B3ZS, or any string of zeros
having length greater than 4 for HDB3.
|
| cds3LCVCount |
.1.3.6.1.4.1.9.9.132.1.3.1.1.7 |
|
The count of both BPVs(Bipolar Violations) and EXZs(Excessive
Zeros) encountered by a T3/E3 interface.An EXZ increments
the LCV by one regardless of the length of the zero string.
|
| cds3PCVCount |
.1.3.6.1.4.1.9.9.132.1.3.1.1.8 |
|
This is the count of P-bit Coding Violation(PCV) error event
encountered by DS3 interface. For all DS3 applications, a
coding violation error event is a P-bit Parity Error(PERR) event.
The parity errors occur when the calculated parity in the
information bits of the DS3 frame does not match up with an
expected parity value.
|
| cds3CPECount |
.1.3.6.1.4.1.9.9.132.1.3.1.1.9 |
|
The number of C-bit parity errors(CPERR) on a DS3 interface.
This value is calculated over noninformation bits in the
DS3 frame.
|
| cds3FEBECount |
.1.3.6.1.4.1.9.9.132.1.3.1.1.10 |
|
The number of Far End Block Errors(FEBE) encountered by
a T3/E3 interface.These include frame alignment errors,
multiframe alignment errors, and C-bit parity errors.
These errors are generated by the transmitter at the
far end, and indicate that the transmitter,cabling or the
upstream node is faulty.
|
| cds3RcvAISCount |
.1.3.6.1.4.1.9.9.132.1.3.1.1.11 |
|
The number of times Alarm Indication Signals(AIS) were detected.
The AIS indicates that an upstream failure has been detected by
the far end.
|
| cds3PlcpStatisticalAlarmSeverity |
.1.3.6.1.4.1.9.9.132.1.2.1.2.1.1 |
|
This variable sets up the severity of PLCP Statistical
alarm. So when PLCP Statistical alarm is detected the
module will send the alarm with appropriate severity.
A value of none(3) indicates that no alarm will be raised.
|
| cds3PlcpBip8CV15MinThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.2.1.2 |
|
The value set in this object determines the value which when exceeded
in a 15 minute window causes a statistical alarm to be declared.
|
| cds3PlcpBip8CV24HrThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.2.1.3 |
|
The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval.
|
| cds3PlcpBip8ES15MinThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.2.1.4 |
|
The value set in this object determines the value which when exceeded
in a 15 minute window causes a statistical alarm to be declared.
|
| cds3PlcpBip8ES24HrThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.2.1.5 |
|
The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval.
|
| cds3PlcpBip8SES15MinThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.2.1.6 |
|
The value set in this object determines the value which when exceeded
in a 15 minute window causes a statistical alarm to be declared.
|
| cds3PlcpBip8SES24HrThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.2.1.7 |
|
The value set in this object determines the value which when exceeded
in a sliding 24 hour window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the preceding 24 hour
interval.
|
| cds3PlcpSEFS15MinThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.2.1.8 |
|
The value set in this object determines the value which when exceeded
in a 15 minute window causes a statistical alarm to be declared.
|
| cds3PlcpSEFS24HrThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.2.1.9 |
|
The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval.
|
| cds3PlcpUAS15MinThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.2.1.10 |
|
The value set in this object determines the value which when
exceeded in a 15 minute window causes a statistical alarm to be
declared.
|
| cds3PlcpUAS24HrThreshold |
.1.3.6.1.4.1.9.9.132.1.2.1.2.1.11 |
|
The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval.
|
| cds3PlcpLineAlarmState |
.1.3.6.1.4.1.9.9.132.1.2.2.1.1 |
|
This variable is a bitmap of the DS3 Line ALarms.
It is represented as sum where value 2^(N-1) is added to the
sum if alarm corresponding to bit N is exceeded.
A value of zero for this object indicates no alarms.
Itemized below are the individual bits:
BitPosition Alarm
----------- -----
1 Receiving RAI
2 Transmitting RAI
3 Receiving OOF
4 Near End Local Loopback in effect
5 Near End Remote Loopback in effect
|
| cds3PlcpLineStatisticalAlarmState |
.1.3.6.1.4.1.9.9.132.1.2.2.1.2 |
|
This variable is a bitmap of the DS3 Plcp Line Statictical
Alarms. It is represented as a sum, where value 2^(N-1) is added
to the sum if threshold corresponding to bit N is exceeded.
A value of zero for this object indicates no alarms.
Itemized below are the individual alarm bits:
BitPosition Alarm
----------- -----
1 Bip8CV 15 minute threshold exceeded
2 Bip8CV 24 hour threshold exceeded
3 Bip8ES 15 minute threshold exceeded
4 Bip8ES 24 hour threshold exceeded
5 Bip8SES 15 minute threshold exceeded
6 Bip8SES 24 hour threshold exceeded
7 Plcp SEFS 15 minute threshold exceeded
8 Plcp SEFS 24 hour threshold exceeded
9 Plcp UAS 15 minute threshold exceeded
10 Plcp UAS 24 hour threshold exceeded
|
| cds3PlcpBip8CVCurrent |
.1.3.6.1.4.1.9.9.132.1.2.2.1.3 |
|
The number of BIP-8 code violations (CV) encountered by
the line in the current 15 minute period.
|
| cds3PlcpBip8CV24HrBucket |
.1.3.6.1.4.1.9.9.132.1.2.2.1.4 |
|
The number of BIP-8 CVs encountered by the line in the last 24
hours.
|
| cds3PlcpBip8ESCurrent |
.1.3.6.1.4.1.9.9.132.1.2.2.1.5 |
|
The number of BIP-8 Errored Seconds(ES) encountered by the line
in the current 15 minute period.
|
| cds3PlcpBip8ES24HrBucket |
.1.3.6.1.4.1.9.9.132.1.2.2.1.6 |
|
The number of BIP-8 ES encountered by the line in the last 24 hour.
|
| cds3PlcpBip8SESCurrent |
.1.3.6.1.4.1.9.9.132.1.2.2.1.7 |
|
The number of BIP-8 Severely Errored Seconds(ES) encountered by the
line in the current 15 minute period.
|
| cds3PlcpBip8SES24HrBucket |
.1.3.6.1.4.1.9.9.132.1.2.2.1.8 |
|
The number of BIP-8 SES encountered by the line in the last 24 hour.
|
| cds3PlcpSEFSCurrent |
.1.3.6.1.4.1.9.9.132.1.2.2.1.9 |
|
The number of BIP-8 Severely Errored Framing Seconds(SEFS)
encountered by the line in the current 15-minute period.
|
| cds3PlcpSEFS24HrBucket |
.1.3.6.1.4.1.9.9.132.1.2.2.1.10 |
|
The number of BIP-8 SEFS encountered by the line in the last 24 hour.
|
| cds3PlcpUASCurrent |
.1.3.6.1.4.1.9.9.132.1.2.2.1.11 |
|
The number of Unavailable Seconds(UAS) encountered by the line
in the current 15-minute period.
|
| cds3PlcpUAS24HrBucket |
.1.3.6.1.4.1.9.9.132.1.2.2.1.12 |
|
The number of BIP-8 UAS encountered by the line in the last 24 hour.
|
| cds3PlcpRcvBip8Count |
.1.3.6.1.4.1.9.9.132.1.3.2.1.1 |
|
The number of of BIP-8 errors encountered by the line.
|
| cds3PlcpRcvOOFCount |
.1.3.6.1.4.1.9.9.132.1.3.2.1.2 |
|
The number of times Out of Frame(OOF) was detected
with or without integrating to OOF alarm.
|
| cds3PlcpRcvRAICount |
.1.3.6.1.4.1.9.9.132.1.3.2.1.3 |
|
The number of times Remote Alarm Indication(RAI) was detected
with or without integrating to RAI alarm.
|
| cds3PlcpFECount |
.1.3.6.1.4.1.9.9.132.1.3.2.1.4 |
|
The number of Framing Errors detected.
|
| cds3PlcpFESecCount |
.1.3.6.1.4.1.9.9.132.1.3.2.1.5 |
|
The number of Framing Error errored seconds.
|
| cds3PlcpSEFSecCount |
.1.3.6.1.4.1.9.9.132.1.3.2.1.6 |
|
The number of Severely errored Framing error seconds.
|
| cds3PlcpFEBECount |
.1.3.6.1.4.1.9.9.132.1.3.2.1.7 |
|
The count of Far End Block Errors (FEBE) detected.
|
| cds3PlcpFEBESecCount |
.1.3.6.1.4.1.9.9.132.1.3.2.1.8 |
|
The number of FEBE errored seconds.
|
| cds3PlcpSEFEBESecCount |
.1.3.6.1.4.1.9.9.132.1.3.2.1.9 |
|
The number of Severely errored FEBE seconds.
|
| cds3IntervalNumber |
.1.3.6.1.4.1.9.9.132.1.3.4.1.1 |
|
A number between 0 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the 15 minute interval completed 23 hours and 45
minutes prior to interval number 1. Interval number
0 refers to the current 15 minute data.
|
| cds3IntervalLSESs |
.1.3.6.1.4.1.9.9.132.1.3.4.1.2 |
|
The number of LSESs encountered by the line
in 15 minute interval.
|
| cds3LCVCurrent24Hr |
.1.3.6.1.4.1.9.9.132.1.3.5.1.1 |
|
The number of LCVs encountered by the line since
the start of current 24 hour period.
|
| cds3LESCurrent24Hr |
.1.3.6.1.4.1.9.9.132.1.3.5.1.2 |
|
The number LESs encountered by the line since
the start of current 24 hour period.
|
| cds3PCVCurrent24Hr |
.1.3.6.1.4.1.9.9.132.1.3.5.1.3 |
|
The number PCVs encountered by the line since
the start of current 24 hour period.
|
| cds3PESCurrent24Hr |
.1.3.6.1.4.1.9.9.132.1.3.5.1.4 |
|
The number of PESs encountered by the line since
the start of current 24 hour period.
|
| cds3PSESCurrent24Hr |
.1.3.6.1.4.1.9.9.132.1.3.5.1.5 |
|
The number of PSESs encountered by the line since
the start of current 24 hour period.
|
| cds3SEFSCurrent24Hr |
.1.3.6.1.4.1.9.9.132.1.3.5.1.6 |
|
The number of SEFSs encountered by the line since
the start of the current 24 hour period.
|
| cds3UASCurrent24Hr |
.1.3.6.1.4.1.9.9.132.1.3.5.1.7 |
|
The number of UASs encountered by the line since
the start of current 24 hour period.
|
| cds3CCVCurrent24Hr |
.1.3.6.1.4.1.9.9.132.1.3.5.1.8 |
|
The number CCVs encounterd by the line since the start
of current 24 hour period.
|
| cds3CESCurrent24Hr |
.1.3.6.1.4.1.9.9.132.1.3.5.1.9 |
|
The number of CESs encountered by the line since the
start of current 24 hour period.
|
| cds3CSESCurrent24Hr |
.1.3.6.1.4.1.9.9.132.1.3.5.1.10 |
|
The number of CSESs encountered by the line since th
start of current 24 hour period.
|
| cds3LSESCurrent24Hr |
.1.3.6.1.4.1.9.9.132.1.3.5.1.11 |
|
The number of LSESs (Line severedly errored seconds)
encountered by the line since the start of current
24 hour period.
|
| cds3LCVPrevious24Hr |
.1.3.6.1.4.1.9.9.132.1.3.6.1.1 |
|
The number of LCVs encountered by the line in
the previous 24 hour period.
|
| cds3LESPrevious24Hr |
.1.3.6.1.4.1.9.9.132.1.3.6.1.2 |
|
The number LESs encountered by the line in
the previous 24 hour period.
|
| cds3PCVPrevious24Hr |
.1.3.6.1.4.1.9.9.132.1.3.6.1.3 |
|
The number PCVs encountered by the line in
the previous 24 hour period.
|
| cds3PESPrevious24Hr |
.1.3.6.1.4.1.9.9.132.1.3.6.1.4 |
|
The number of PESs encountered by the line in
the previous 24 hour period.
|
| cds3PSESPrevious24Hr |
.1.3.6.1.4.1.9.9.132.1.3.6.1.5 |
|
The number of PSESs encountered by the line in
the previous 24 hour period.
|
| cds3SEFSPrevious24Hr |
.1.3.6.1.4.1.9.9.132.1.3.6.1.6 |
|
The number of SEFSs encountered by the line in
the start of the current 24 hour period.
|
| cds3UASPrevious24Hr |
.1.3.6.1.4.1.9.9.132.1.3.6.1.7 |
|
The number of UASs encountered by the line in
the previous 24 hour period.
|
| cds3CCVPrevious24Hr |
.1.3.6.1.4.1.9.9.132.1.3.6.1.8 |
|
The number CCVs encounterd by the line in the
previous 24 hour period.
|
| cds3CESPrevious24Hr |
.1.3.6.1.4.1.9.9.132.1.3.6.1.9 |
|
The number of CESs encountered by the line in
the previous 24 hour period.
|
| cds3CSESPrevious24Hr |
.1.3.6.1.4.1.9.9.132.1.3.6.1.10 |
|
The number of CSESs encountered by the line in
the previous 24 hour period.
|
| cds3LSESPrevious24Hr |
.1.3.6.1.4.1.9.9.132.1.3.6.1.11 |
|
The number of LSESs encountered by the line in
the previous 24 hour period.
|
