cisco-queue-mib.mib object
Introduction
Most network devices and programs ship with so-called MIB files to describe the parameters and meanings (i.e.: friendly names) which are available for monitoring via SNMP.
ActiveXperts Network Monitor 2025 can import vendor-specific MIB files, so it can be used to monitor specific OID's (Object Identifiers).
This way, you can monitor your devices, computers, etc. by selecting your relevant OID's by name.
ActiveXperts Network Monitor 2025 can import MIB file cisco-queue-mib and use it to monitor vendor specific OID's.
cisco-queue-mib file content
Object view of cisco-queue-mib:
| Scalar Object |
| cQIfEntry |
.1.3.6.1.4.1.9.9.37.1.1.1 |
|
A list of queue attributes for an interface.
|
| cQStatsEntry |
.1.3.6.1.4.1.9.9.37.1.2.1 |
|
A list of sub-queue attributes for an interface.
|
| cQRotationEntry |
.1.3.6.1.4.1.9.9.37.1.3.1 |
|
Custom Queuing sub-queue attributes for an interface.
|
| Tabular Object |
| cQIfQType |
.1.3.6.1.4.1.9.9.37.1.1.1.1 |
|
The type of queuing used in the Hold Queue.
First In First Out Queuing implies that the interface always
transmits messages in the order that they are received.
Priority Queuing sorts messages out by the use of access lists.
Messages in a higher priority queue are always sent in
preference to messages in a lower priority queue.
Custom Queuing sorts messages out by the use of access lists.
Sub-queues are selected in round robin order as either the
sub-queue is drained or a given number of octets is moved from
the sub-queue to the transmission queue.
Weighted Fair Queuing sorts messages by 'conversation', which
is source-destination pair of addresses and sockets or ports,
as defined by the network layer protocol. Messages are removed
from queues in a sequence that gives each conversation a
proportion of the available bandwidth.
|
| cQIfTxLimit |
.1.3.6.1.4.1.9.9.37.1.1.1.2 |
|
The maximum number of messages placed into the hardware
transmission queue. This is a first come first serve queue, fed
by the hold queue. If the hold queue contains information,
this queue is presumably full.
|
| cQIfSubqueues |
.1.3.6.1.4.1.9.9.37.1.1.1.3 |
|
The number of sub-queues of which the hold queue is built.
This is a constant for each value of cQIfQType.
|
| cQStatsQNumber |
.1.3.6.1.4.1.9.9.37.1.2.1.1 |
|
The number of the queue within the queue set.
In FIFO queuing, this value is always 2.
In Priority Queuing, it corresponds to the various priorities:
high = 0
medium = 1
normal = 2
low = 3
In Custom Queuing, it is the queue number referenced in the
access list.
In Weighted Fair Queuing, it is the queue number associated
with the traffic stream (conversation) identified.
|
| cQStatsDepth |
.1.3.6.1.4.1.9.9.37.1.2.1.2 |
|
The number of messages in the sub-queue.
|
| cQStatsMaxDepth |
.1.3.6.1.4.1.9.9.37.1.2.1.3 |
|
The maximum number of messages permitted in the sub-queue.
|
| cQStatsDiscards |
.1.3.6.1.4.1.9.9.37.1.2.1.4 |
|
The number of messages discarded from this queue since restart
by reason of enqueue at a time that cQStatsDepth >= cQStatsMaxDepth.
|
| cQRotationOctets |
.1.3.6.1.4.1.9.9.37.1.3.1.1 |
|
The number of octets which may be transmitted from a custom
queuing sub-queue before it must yield to another queue.
|
| Table |
| cQIfTable |
.1.3.6.1.4.1.9.9.37.1.1 |
|
This table contains objects that describe the queues on a
Cisco Interface.
An interface queue is modeled as a collection of one or more
secondary queues that feed into a device's hardware queue. The
hardware queue has a maximum depth set by the MCI tx-queue-limit
command or equivalent. The secondary queues (also known as the
'hold queue') have maximum depths set by the hold-queue command
or equivalent.
This table parallels the ifTable, and indicates the type of
queuing in use on the interface, number of queues, and similar
parameters.
|
| cQStatsTable |
.1.3.6.1.4.1.9.9.37.1.2 |
|
This table contains statistical objects that for the
sub-queues of a Cisco Interface.
|
| cQRotationTable |
.1.3.6.1.4.1.9.9.37.1.3 |
|
This table describes the rotation of Custom Queuing on an
Interface.
|
| Object Identifier |
| ciscoQueueMIB |
.1.3.6.1.4.1.9.9.37 |
|
This is the MIB module for objects used to manage
interface queuing in Cisco devices.
|
| ciscoQueueObjects |
.1.3.6.1.4.1.9.9.37.1 |
| ciscoQueueTraps |
.1.3.6.1.4.1.9.9.37.2 |
| ciscoQueueConformance |
.1.3.6.1.4.1.9.9.37.3 |
| cQCompliances |
.1.3.6.1.4.1.9.9.37.3.1 |
| cQGroups |
.1.3.6.1.4.1.9.9.37.3.2 |
| Group |
| cQIfGroup |
.1.3.6.1.4.1.9.9.37.3.2.1 |
|
The configuration of queuing on the interface. Interface
Queuing statistics (ifOutQDepth and ifOutDiscards) are kept in
the interface table.
|
| cQStatsGroup |
.1.3.6.1.4.1.9.9.37.3.2.2 |
|
The statistics for individual queues in the interface queuing
system.
|
| cQRotationGroup |
.1.3.6.1.4.1.9.9.37.3.2.3 |
|
The Custom Queuing queue rotation weights.
|
