cisco-udldp-mib.mib object
Introduction
Most network devices and programs ship with so-called MIB files to describe the parameters and meanings (i.e.: friendly names) which are available for monitoring via SNMP.
ActiveXperts Network Monitor 2025 can import vendor-specific MIB files, so it can be used to monitor specific OID's (Object Identifiers).
This way, you can monitor your devices, computers, etc. by selecting your relevant OID's by name.
ActiveXperts Network Monitor 2025 can import MIB file cisco-udldp-mib and use it to monitor vendor specific OID's.
cisco-udldp-mib file content
Object view of cisco-udldp-mib:
| Scalar Object |
| cudldpGlobalEnable |
.1.3.6.1.4.1.9.9.118.1.1.1 |
|
This variable is used to
enable(true)/disable(false) Uni Direction
Link Detection Protocol on the device.
cudldpGlobalEnable is deprecated and
replaced with cudldpGlobalMode.
|
| cudldpHelloInterval |
.1.3.6.1.4.1.9.9.118.1.1.2 |
|
Indicates interval in seconds at which each port
sends a hello packet to all of its neighbors at
steady state when the link has been identified as
bidirectional.
|
| cudldpGlobalMode |
.1.3.6.1.4.1.9.9.118.1.1.3 |
|
Indicates the mode of UDLDP feature on the device.
enable -- Uni Direction Link Detection Protocol is
enabled on the device.
disable -- Uni Directional Link Detection Protocol is
disabled on the device.
aggresive -- Uni Directional Link Detection protocol
is enabled in aggressive mode on the
device.
|
| cudldpInterfaceEntry |
.1.3.6.1.4.1.9.9.118.1.2.1.1 |
|
A conceptual row of cudldpInterfaceTable. An
entry exists for each interface that supports
UDLDP.
|
| Tabular Object |
| cudldpInterfaceEnable |
.1.3.6.1.4.1.9.9.118.1.2.1.1.1 |
|
This variable is used to enable UDLDP on this
interface. If cudldpGlobalEnable is set to
'false' then this variable has no effect.
cudldpInterfaceEnable is deprecated and
replaced with cudldpInterfaceAdminMode.
|
| cudldpInterfaceOperStatus |
.1.3.6.1.4.1.9.9.118.1.2.1.1.2 |
|
This mib oject contains the following values,
which has the meaning as:
'shutdown' - An Uni-Direction link has been
detected and the port has been
disabled.
'indeterminant' - Uni-Direction Link Detection
protocol has not collected enough
information to determine if the
link is bi directional or not.
'biDirectional' - A bi directional link has been
detected.
'notApplicable' - Uni-Direction Link Detection
Protocol is disabled.
|
| cudldpInterfaceAggressiveMode |
.1.3.6.1.4.1.9.9.118.1.2.1.1.3 |
|
An indication of whether the UDLDP aggressive mode
is enabled on this interface. If the
aggressive mode is set to 'true', an active port may
be shutdown in case of the abrupt loss of its
neighbor(s) because the loss of communication
(heartbeat) with the neighbor(s) is assumed to be
caused by a fault; thus, the cudldpInterfaceOperStatus
of the active port will be 'shutdown'. Instead, when
the aggressive mode is set to 'false', and if there
is a loss of communication with the neighbor(s), then
the cudldpInterfaceOperStatus of the active port
will be 'indeterminant'.
Therefore, this mode is recommended
only for links that don't use hubs, media converters
or similar devices, and where the unexpected loss of
the port's neighbor is not an admissible condition.
cudldpInterfaceAggressiveMode is deprecated and
replaced with cudldpInterfaceAdminMode.
|
| cudldpInterfaceAdminMode |
.1.3.6.1.4.1.9.9.118.1.2.1.1.4 |
|
Indicates the Administartive mode of Uni Direction
Link Detection Protocol Feature configured on this
interface.
enable -- Uni Direction Link Detection Protocol is
enabled on this interface.
disable -- Uni Direction Link Detection Protocol is
disabled on this interface.
aggressive -- Uni Direction Link Detection protocol
is enabled in aggressive mode on this
interface.
default -- Whether the Uni Directiona Link Detection
protocol is enabled or not on this interface
depends on the object value of
cudldpGlobalMode.
|
| cudldpInterfaceOperMode |
.1.3.6.1.4.1.9.9.118.1.2.1.1.5 |
|
Indicates the operational mode of Uni Direction Link
Detection Protocol Feature on this interface.
|
| Table |
| cudldpInterfaceTable |
.1.3.6.1.4.1.9.9.118.1.2.1 |
|
The (conceptual) table containing the status
of UDLDP on the device's interfaces.
|
| Object Identifier |
| ciscoUdldpMIB |
.1.3.6.1.4.1.9.9.118 |
|
Cisco Uni Direction Link Detection Protocol
MIB
|
| ciscoUdldpMIBObjects |
.1.3.6.1.4.1.9.9.118.1 |
| cudldpGlobal |
.1.3.6.1.4.1.9.9.118.1.1 |
| cudldpInterface |
.1.3.6.1.4.1.9.9.118.1.2 |
| ciscoUdldpMIBConformance |
.1.3.6.1.4.1.9.9.118.3 |
| ciscoUdldpMIBCompliances |
.1.3.6.1.4.1.9.9.118.3.1 |
| ciscoUdldpMIBGroups |
.1.3.6.1.4.1.9.9.118.3.2 |
| Group |
| ciscoUdldpMIBGroup |
.1.3.6.1.4.1.9.9.118.3.2.1 |
|
A collection of objects for use with the Uni Direction
Link Detection Protocol.
|
| ciscoUdldpAggreModeOptionalGroup |
.1.3.6.1.4.1.9.9.118.3.2.2 |
|
A collection of optional objects providing UDLDP
aggressive mode configuration information.
|
| ciscoUdldpMIBGroup2 |
.1.3.6.1.4.1.9.9.118.3.2.3 |
|
A collection of objects providing Uni Direction
Link Detection Protocol information.
|
