| cwmIndex |
.1.3.6.1.4.1.9.9.145.1.1.1.1.1 |
|
This object's value generally corresponds to the
slot number where the module resides. However,
system wide uniqueness is the only true requirement.
|
| cwmIngressSCTFileId |
.1.3.6.1.4.1.9.9.145.1.1.1.1.2 |
|
The file ID of the Service Class Template(SCT) file. The SCT
holds the connection specific parameters for this module in
the ingress direction(From Network to the Switch).
Terminologies used:
SCT : Service Class Template
The Service Class Template ( or Service Template or SCT )
provides a means for inferring extended parameters, which
are generally platform-specific, from the set of standard
ATM protocol parameters passed in VSI(Virtual Switch Interface)
connection setup primitives. A set of Service Templates are
available in a non-volatile storage and is downloaded onto
each Service Module on power up.
In general, SCTs contain two classes of data. One class consists
of parameters necessary to establish a Virtual Connection
(i.e. Per-VC) and includes entries such as UPC(Usage Parameter Control)
actions, various bandwidth-related items, per-VC thresholds,
and some hardware-specific items.The second class of data items
includes those necessary to configure the associated
Class-of-Service Buffers that provide the QoS support.
|
| cwmIngressSCTFileName |
.1.3.6.1.4.1.9.9.145.1.1.1.1.3 |
|
This variable contains the SCT filename. Write access
is not required. The filename has cwmIngressSCTFileId
value as the suffix. For example, the value SCT.INGR.13
for this object indicates 13 is the value of
cwmIngressSCTFileId.
|
| cwmAutoLineDiagEnable |
.1.3.6.1.4.1.9.9.145.1.1.1.1.4 |
|
This object enables/disables automatic diagnostic feature
of physical lines on module.
In case of a line alarm, enabling this feature temporarily
suspends traffic in both direction and starts local loop-back
testing. Disabling this feature will not effect the traffic
in one direction while another direction is in alarm.
|
| cwmSCTFileVerCfg |
.1.3.6.1.4.1.9.9.145.1.1.1.1.5 |
|
The Configured version of the Service Class Template(SCT)
file. This version applies to both the card SCT and the port
SCT files in a service module.
The port SCT files are specified while provisioning a port using
the caviFileId field in the CISCO-WAN-VIRTUAL-IF-MIB.my MIB.
The card SCT file is specifed in this MIB using the
cwmIngressSCTFileName object.
The configured version of the SCT does not take effect until
the service module is rebooted. However, graceful invocation
of a new SCT version can be achieved by using redundant service
modules. The configured SCT version is first applied on a standby
service module by rebooting it. When the standby reboots, it
comes up with the configured SCT version. Thereafter a switchover
can be performed, making the standby SM take over as active.
|
| cwmSCTFileVerOpr |
.1.3.6.1.4.1.9.9.145.1.1.1.1.6 |
|
The operational version of the Service Class Template(SCT)
file. This is sct version currently in use. The operational
version could be different from the configured version
(cwmSCTFileVerCfg), until the service module is rebooted.
|
| cwmUploadCounter |
.1.3.6.1.4.1.9.9.145.1.1.1.1.7 |
|
This counter is used by the management station to
determine if any changes(other than ATM/FR connections)
have been done on configuration of a card.
The use of this object is implementation specific.
This requires the NMS application saving the previous
value of this object and compare it later for finding
any changes in the card.
The upload counter is incremented in, for instance:
- any physical interface characteristics are modified.
- any logical interface is added/deleted/modified.
- any IMA Group/MFR bundle is added/deleted/modified.
- any resource is added/deleted/modified on an interface.
- any configuration changes are done(not specified above)
which are not related to ATM/FR Connections
(SPVCs for example).
|
| cwmStatBucketInterval |
.1.3.6.1.4.1.9.9.145.1.2.1.1.1 |
|
This object contains the bucket interval in minutes used in
collecting statistics. This specifies the interval over
which the module accumulates a sample. This value also
defines the amount of time available to NMS application
to upload the statistic file in order to not miss one
interval worth of data.
|
| cwmStatCollectionInterval |
.1.3.6.1.4.1.9.9.145.1.2.1.1.2 |
|
The collection interval of statistics. Within a sampling interval,
as defined by cwmStatBucketInterval, statistics counters are
updated every collection interval.
Default value of collection interval is same as bucket interval.
In case of bucket interval being 5 minutes, default(0) and five(5)
values for this object has the same effect.
|
| cwmStatCollectionStatus |
.1.3.6.1.4.1.9.9.145.1.2.1.1.3 |
|
Enables or disables statistics collection on the module.
|
| cwmStatCurrentLevel |
.1.3.6.1.4.1.9.9.145.1.2.1.1.4 |
|
The current statistics level of the module.
A change in the card statistic level can take place only
after a module reset. This object shows the current module
statistic level. While cwmStatLevelConfigured object is
used to configure module statistic level. The value
set in cwmStatLevelConfigured object will take effect after
next module reset.
|
| cwmStatLevelConfigured |
.1.3.6.1.4.1.9.9.145.1.2.1.1.5 |
|
This object is used to configure the statistics level
for the module. The statistics level value set in this
object will take effect only on reset of the module.
This object can be set only if cwmStatCollectionStatus is set
to enable(1). This object cannot be set to notApplicable(0).
|
| cwmStatMaximumConnections |
.1.3.6.1.4.1.9.9.145.1.2.1.1.6 |
|
The maximum number of connections for which the statistics are
being collected.
|
