| h323TermSystemDescr |
.0.0.8.341.1.0.1.3.1.1.1.1 |
|
A textual description of the terminal. Name of
manufacturer.
|
| h323TermSystemHWVersionNo |
.0.0.8.341.1.0.1.3.1.1.1.2 |
|
Hardware version number.
|
| h323TermSystemSWVersionNo |
.0.0.8.341.1.0.1.3.1.1.1.3 |
|
Software version number.
|
| h323TermSystemContact |
.0.0.8.341.1.0.1.3.1.1.1.4 |
|
The textual identification of the contact person
for this managed node, together with information
on how to contact this person.
|
| h323TermSystemt35CountryCode |
.0.0.8.341.1.0.1.3.1.1.1.5 |
|
Country code, per T.35.
|
| h323TermSystemt35CountryCodeExtention |
.0.0.8.341.1.0.1.3.1.1.1.6 |
|
Assigned nationally.
|
| h323TermSystemt35ManufacturerCode |
.0.0.8.341.1.0.1.3.1.1.1.7 |
|
Assigned nationally.
|
| h323TermSystemLocation |
.0.0.8.341.1.0.1.3.1.1.1.8 |
|
The physical location of this system. For instance, closet,
terminal room and so on
|
| h323TermSystemUptime |
.0.0.8.341.1.0.1.3.1.1.1.9 |
|
The amount of time (in hundredths of a second) since
this H323 terminal was last initialized. Note that this
is different from sysUpTime in MIB-II because
sysUpTime is the uptime of the network management
portion of the system.
|
| h323TermSystemLocalTime |
.0.0.8.341.1.0.1.3.1.1.1.10 |
|
The local date and time of day.
|
| h323TermSystemDiagnostics |
.0.0.8.341.1.0.1.3.1.1.1.11 |
|
Indicates the results of the last diagnostic routine
performed
noResults(1) No diagnostic has yet been performed,
passed(2) the diagnostic has been passed,
hardwareFault(3) Hardware fault was detected,
softwareFault(4) Software fault was detected
|
| h323TermSystemStatus |
.0.0.8.341.1.0.1.3.1.1.1.12 |
|
General status of the terminal
|
| h323TerminalCapsMaxLineRate |
.0.0.8.341.1.0.1.3.2.1.1.1 |
|
This object represents maximum line rate of combined
audio/video and data in kbit/s of this terminal.
|
| h323TerminalCapsVideoCaps |
.0.0.8.341.1.0.1.3.2.1.1.2 |
|
This object represents the video capabilities of this
terminal
|
| h323TerminalCapsMaxVideoRate |
.0.0.8.341.1.0.1.3.2.1.1.3 |
|
The maximum bit rate that the video channel can do.
|
| h323TerminalCapsAudioCaps |
.0.0.8.341.1.0.1.3.2.1.1.4 |
|
This object represents the audio capabilities of this
terminal.
|
| h323TerminalCapsDataCaps |
.0.0.8.341.1.0.1.3.2.1.1.5 |
|
This object represents the data application
capability of the terminal.
|
| h323TerminalCapsRDCCaps |
.0.0.8.341.1.0.1.3.2.1.1.6 |
|
This object represents the Remote Device Control
capability of the terminal.
other 0
FECC 1 -- Far-end Camera Control
Bits are numbered starting with the most
significant bit of the first byte being bit 0, the
least significant bit of the first byte being bit
7, the most significant bit of the second byte
being bit 8, and so on. A one bit encodes that
the capability is supported, a zero bit encodes that
the capability is not supported.
|
| h323TerminalControlAdminControl |
.0.0.8.341.1.0.1.3.3.1.1.1 |
|
The desired state of the H323 terminal. Setting the value
if this object to these values will have the
following actions:
run(1) The H323 terminal will enter the run state,
reset(2) The H323 terminal will reset,
diagnose(3) Will activate the diagnostic routine,
stop(4) Will halt the H323 terminal.
|
| h323TerminalControlEnableLocalLoopback |
.0.0.8.341.1.0.1.3.3.1.1.2 |
|
Enable or disable local system loopback on a video
conference system. Local loopbacks loop back the audio,
video and data streams in a call. Once looped back,
a new call will show up in the Call Table and the
user can observe the audio/video/data rates to assure
that these components are working properly.
|
| h323TerminalControlEnableRemoteLoopback |
.0.0.8.341.1.0.1.3.3.1.1.3 |
|
Enable or disable remote system loopback on a video
conference system. Remote loopbacks loop back the audio
and video streams from the remote system in
a call.. When the remote system
calls in, a new call will show up in the
Call Table and the user can observe the
audio/video/data rates to assure that these
components are coming in properly from the
remote system.
|
