| frNniTraceIndex |
.1.3.6.1.4.1.562.2.4.1.70.7.1.1.10 |
|
This variable represents the index for the frNniTrace tables.
|
| frNniTraceRowStatus |
.1.3.6.1.4.1.562.2.4.1.70.7.1.1.1 |
|
This variable is used as the basis for SNMP naming of
frNniTrace components.
These components can be added and deleted.
|
| frNniTraceComponentName |
.1.3.6.1.4.1.562.2.4.1.70.7.1.1.2 |
|
This variable provides the component's string name for
use with the ASCII Console Interface
|
| frNniTraceStorageType |
.1.3.6.1.4.1.562.2.4.1.70.7.1.1.4 |
|
This variable represents the storage type value for the
frNniTrace tables.
|
| frNniTraceReceiverName |
.1.3.6.1.4.1.562.2.4.1.70.7.10.1.2 |
|
This attribute should be set to the name of the desired trace receiver
before starting a trace session. All available trace receivers are listed
under the Trace Rcvr/<string> component. This attribute cannot be
set while a trace is active.
|
| frNniTraceDuration |
.1.3.6.1.4.1.562.2.4.1.70.7.10.1.3 |
|
This attribute specifies the duration, in minutes, of a trace session.
A value of 0 indicates unlimited duration in which case a trace
session remains active until a stop command is issued. The default
duration is 60 minutes. This attribute cannot be set while a trace is
active.
|
| frNniTraceQueueLimit |
.1.3.6.1.4.1.562.2.4.1.70.7.10.1.4 |
|
This attribute specifies the total number of bytes of traced data
which may be queued for transmission to the trace receiver. When
this limit is exceeded, incoming traced frames are discarded. This
attribute can be set while a trace is active and takes effect
immediately.
|
| frNniTraceSession |
.1.3.6.1.4.1.562.2.4.1.70.7.10.1.5 |
|
This attribute is set automatically. It identifies the Trace Session
component which is forwarding the trace data. This attribute is
empty unless a trace is active.
|
| frNniTraceFilterIndex |
.1.3.6.1.4.1.562.2.4.1.70.7.2.1.1.10 |
|
This variable represents the index for the frNniTraceFilter tables.
|
| frNniTraceFilterRowStatus |
.1.3.6.1.4.1.562.2.4.1.70.7.2.1.1.1 |
|
This variable is used as the basis for SNMP naming of
frNniTraceFilter components.
These components cannot be added nor deleted.
|
| frNniTraceFilterComponentName |
.1.3.6.1.4.1.562.2.4.1.70.7.2.1.1.2 |
|
This variable provides the component's string name for
use with the ASCII Console Interface
|
| frNniTraceFilterStorageType |
.1.3.6.1.4.1.562.2.4.1.70.7.2.1.1.4 |
|
This variable represents the storage type value for the
frNniTraceFilter tables.
|
| frNniTraceFilterTraceType |
.1.3.6.1.4.1.562.2.4.1.70.7.2.10.1.1 |
|
This attribute specifies the level of filtering required for this trace
session. A value of lmi indicates that Lmi frames are traced. A
value of dlci indicates that frames from the Dlci specified by the
tracedDlci attribute are traced. A value of badFrames indicates that
bad received frames (overruns, CRC errors, aborts) are traced. The
default is to trace all frames. This attribute can be set while a trace
is active and takes effect immediately.
Description of bits:
lmi(0)
dlci(1)
badFrames(2)
|
| frNniTraceFilterTracedDlci |
.1.3.6.1.4.1.562.2.4.1.70.7.2.10.1.2 |
|
This attribute specifies a particular Dlci to trace. A value of zero
specifies that all Dlcis are to be traced. This attribute can be set
while a trace is active and takes effect immediately.
|
| frNniTraceFilterDirection |
.1.3.6.1.4.1.562.2.4.1.70.7.2.10.1.3 |
|
This attribute specifies the direction of the data to be traced as
viewed by the service. The values can be egress, and/or ingress. An
egress value indicates frames outbound from the service. An
ingress value indicates frames inbound to the service. This attribute
can be set while a trace is active and takes effect immediately.
Description of bits:
egress(0)
ingress(1)
|
| frNniTraceFilterTracedLength |
.1.3.6.1.4.1.562.2.4.1.70.7.2.10.1.4 |
|
This attribute specifies the maximum number of bytes to trace per
frame starting from the byte following the frame flag. If the frame
length is longer than the value specified by this attribute, then the
traced frame is truncated. This attribute can be set while a trace is
active and takes effect immediately.
|
