ActiveXperts Network Monitor 2019##AdminFavorites

EBN-MIB.mib object view, vendor RFC

Introduction

Most network devices and programs ship with so-called MIB files to describe the parameters and meanings (i.e.: friendly names) which are available for monitoring via SNMP.
ActiveXperts Network Monitor 2019 can import vendor-specific MIB files, so it can be used to monitor specific OID's (Object Identifiers). This way, you can monitor your devices, computers, etc. by selecting your relevant OID's by name.

ActiveXperts Network Monitor 2019 can import MIB file EBN-MIB and use it to monitor vendor specific OID's.

EBN-MIB file content

Object view of EBN-MIB:

Scalar Object
ebnDirEntry .1.3.6.1.2.1.34.7.1.1.1.1
Entry in the EBN Directory Table.
ebnIsRscvEntry .1.3.6.1.2.1.34.7.1.2.1.1
Entry in ebnIsRscvTable.
ebnSearchCacheTime .1.3.6.1.2.1.34.7.1.3.1
The amount of time in minutes an extended border node will retain information about a multi-subnetwork search, once that that search terminates. A value 0 indicates that the EBN has no defined limit, and the number of entries is bounded only by memory.
ebnMaxSearchCache .1.3.6.1.2.1.34.7.1.3.2
The maximum number of multi-subnet entries to be cached. The value 0 indicates that the local node has no defined limit, and the number of entries is bounded only by memory.
ebnDefaultSubnetVisitCount .1.3.6.1.2.1.34.7.1.3.3
The default maximum number of subnetworks a LOCATE search procedure may traverse.
ebnCosMapEntry .1.3.6.1.2.1.34.7.1.4.1.1
An entry in the EBN COS Mapping table.
ebnSubnetSearchEntry .1.3.6.1.2.1.34.7.1.5.1.1
An entry for the ebnSubnetSearchTable. The entry represents the configured parameters the EBN uses when it is determining how to search for the LU identified by the ebnSubnetSearchLuName object.
ebnSearchEntry .1.3.6.1.2.1.34.7.1.5.2.1
An entry in the ebnSearchTable. An entry can exist in this table only if an entry exists in the ebnSubnetSearchTable with an ebnSubnetSearchLuName value matching this entry's ebnSearchLuName. For a given ebnSearchLuName value, the ordering of entries provides by the ebnSearchIndex values corresponds to the order in which the control points to be searched appear in the CONFIGURED search list for the ebnSearchLuName.
hbnIsInEntry .1.3.6.1.2.1.34.7.1.6.1.1
Entry of the HBN Intermediate Session Table. An entry exists in this table for every intermediate session being routed between back-to-back RTP connections in the HBN. When an entry for a session exists in this table, the NceIds and Tcids for the back-to-back RTP connections are made available in the following four objects: RTP connection in the direction of the PLU: - NceId: appnIsInRtpNceId (in the APPN MIB) - Tcid: appnIsinRtpTcid (in the APPN MIB). RTP connection in the direction of the SLU: - NceId: hbnIsInRtpNceId (in this table) - Tcid: hbnIsInRtpTcid (in this table).
Tabular Object
ebnDirLuName .1.3.6.1.2.1.34.7.1.1.1.1.1
Fully qualified network LU name in the domain of a serving network node. If this object has the same value as the appnDirLuName object in the APPN MIB, then the two objects are referring to the same LU.
ebnDirSubnetAffiliation .1.3.6.1.2.1.34.7.1.1.1.1.2
Specifies the subnetwork affiliation of the LU: - native(1) : The LU is in the native APPN subnetwork. - nonNative(2) : The LU is in a non-native APPN subnetwork. - subarea(3) : The LU is in a subarea network.
ebnIsRscvCpName .1.3.6.1.2.1.34.7.1.2.1.1.1
The network-qualified control point name of the node at which the session and PCID originated. For APPN and LEN nodes, this is either CP name of the APPN node at which the origin LU is located or the CP name of the NN serving the LEN node at which the origin LU is located. For DLUR resources it is the name of the owning SSCP. If this object has the same value as the appnIsInFqCpName object in the APPN MIB, then the two objects are referring to the same APPN control point.
ebnIsRscvPcid .1.3.6.1.2.1.34.7.1.2.1.1.2
The procedure correlation identifier (PCID) of a session. It is an 8-octet value. If this object has the same value as the appnIsInPcid object in the APPN MIB, and if the corresponding ebnIsRscvCpName object has the same value as the corresponding appnIsInFqCpName object, then the entries indexed by these objects are referring to the same session.
ebnIsRscvDestinationRoute .1.3.6.1.2.1.34.7.1.2.1.1.3
The route selection control vector (RSCV x'2B') used in the direction towards the SLU.
ebnIsRscvDestinationCos .1.3.6.1.2.1.34.7.1.2.1.1.4
The Class of Service (COS) name used in the direction towards the SLU. Because the characters allowed in an SNA COS name come from a restricted character set, these names are not subject to internationalization.
ebnCosMapCpName .1.3.6.1.2.1.34.7.1.4.1.1.1
Fully qualified network CP name for which the COS mapping applies.
ebnCosMapNonNativeCos .1.3.6.1.2.1.34.7.1.4.1.1.2
This object contains one of the following values: - An 8-character COS name used in a non-native subnetwork. - The single character '*', identifying the entry with the default native COS for a non-native CP name. This entry is used when there is no entry in the table for a non-native CP name / non-native COS pair. Because the characters allowed in an SNA COS name come from a restricted character set, these names are not subject to internationalization.
ebnCosMapNativeCos .1.3.6.1.2.1.34.7.1.4.1.1.3
An 8-byte name for the class-of-service, as known in the native subnetwork. Because the characters allowed in an SNA COS name come from a restricted character set, these names are not subject to internationalization.
ebnSubnetSearchLuName .1.3.6.1.2.1.34.7.1.5.1.1.1
Fully qualified network LU name.
ebnSubnetSearchDynamics .1.3.6.1.2.1.34.7.1.5.1.1.2
Indicates whether an EBN may add dynamic entries to a subnetwork routing list. none(1) means no entries may be added to the subnetwork routing list. limited(2) means only likely entries may be added to the subnetwork routing list. full(3) means all native extended border nodes and adjacent, non-native EBNs and NNs will be added to the subnetwork routing list.
ebnSubnetSearchOrdering .1.3.6.1.2.1.34.7.1.5.1.1.3
Indicates whether an EBN may reorder a subnetwork routing list so that entries which are more likely to be successful move to the top of the subnetwork routing list and entries which are more likely to be unsuccessful move to the bottom of the list. The following values are defined: - priority(1): Entries may be reordered. - defined(2): Entries must not be reordered.
ebnSearchLuName .1.3.6.1.2.1.34.7.1.5.2.1.1
Fully qualified network LU name. If this object has the same value as the ebnSubnetSearchLuName object, then the two objects are referring to the same LU.
ebnSearchIndex .1.3.6.1.2.1.34.7.1.5.2.1.2
Secondary index enumerating the CONFIGURED order in which a search is forwarded to CPs for a particular LU name. The order for an actual search is determined dynamically by the EBN, based on this configured information and on other factors, including whether search dynamics and search ordering are enabled. Information on these last two settings is available in, respectively, the ebnSubnetSearchDynamics and ebnSubnetSearch ordering objects.
ebnSearchCpName .1.3.6.1.2.1.34.7.1.5.2.1.3
This object specifies the CP(s) to which a search should be forwarded. It either follows the SnaNAUWildcardName textual convention or takes one of the following special formats: '*' indicates that all native EBNs and all adjacent non- native EBNs and NNs may be added to the routing list dynamically, '*SELF' indicates that the EBN should search itself and its native subnetwork at this time during the cross-subnet search, '*EBNS' indicates all native EBNs. Because the characters allowed in a CP name come from a restricted character set, and because the three formats listed here use no special characters, this object is not subject to internationalization.
ebnSearchSNVC .1.3.6.1.2.1.34.7.1.5.2.1.4
The maximum number of subnets a Locate search procedure may traverse.
hbnIsInFqCpName .1.3.6.1.2.1.34.7.1.6.1.1.1
The network-qualified control point name of the node at which the session and PCID originated. For APPN and LEN nodes, this is either the CP name of the APPN node at which the origin LU is located or the CP name of the NN serving the LEN node at which the origin LU is located. If this object has the same value as the appnIsInFqCpName object in the APPN MIB, then the two objects are referring to the same APPN control point.
hbnIsInPcid .1.3.6.1.2.1.34.7.1.6.1.1.2
The procedure correlation identifier (PCID) of a session. It is an 8-octet value. If this object has the same value as the appnIsInPcid object in the APPN MIB, and if the corresponding hbnIsInFqCpName object has the same value as the corresponding appnIsInFqCpName object, then the entries indexed by these objects are referring to the same session.
hbnIsInRtpNceId .1.3.6.1.2.1.34.7.1.6.1.1.3
The HPR local Network Connection Endpoint of the session in the direction of the SLU.
hbnIsInRtpTcid .1.3.6.1.2.1.34.7.1.6.1.1.4
The RTP connection local TCID of the session in the direction of the SLU.
Table
ebnDirTable .1.3.6.1.2.1.34.7.1.1.1
The EBN Directory Table. This table is an extension to the APPN MIB's appnDirTable. Entries in this table are in one-to-one correspondence with entries in the appnDirTable, with corresponding entries having identical values for their respective indexes.
ebnIsRscvTable .1.3.6.1.2.1.34.7.1.2.1
The EBN Intermediate Session RSCV table. This table is an extension to the appnIsInTable. It contains the RSCV and COS used in the direction of the BIND destination. There is an entry in this table for each session that traverses an ISTG when it enters or leaves this EBN, with corresponding entries having identical values for their respective indexes.
ebnCosMapTable .1.3.6.1.2.1.34.7.1.4.1
The EBN COS Mapping Table. This table specifies how non- native COS values are mapped to COS values defined in the native subnetwork. Note: The COS mappings that an EBN performs are determined by multiple factors, one of which is a set of user-defined initial mappings. This table returns the COS mappings that the EBN is actually performing at the time it is queried, rather than the user-defined initial ones.
ebnSubnetSearchTable .1.3.6.1.2.1.34.7.1.5.1
This table contains one entry for each fully qualified LU name for which an associated subnet routing list has been defined. An entry in this table contains general characteristics of the subnet search routing list for an LU name. The routing list itself is represented by a set of contiguous entries in the ebnSearchTable.
ebnSearchTable .1.3.6.1.2.1.34.7.1.5.2
This table indicates the CONFIGURED list of control points to which the EBN sends Locate searches for a given fully qualified LU name. Each entry in the table indicates one control point that should be included in a multi-subnet search for a particular LU name.
hbnIsInTable .1.3.6.1.2.1.34.7.1.6.1
The HBN Intermediate Session table.
Object Identifier
ebnMIB .1.3.6.1.2.1.34.7
The MIB Module for Extended Border Node
ebnObjects .1.3.6.1.2.1.34.7.1
ebnDir .1.3.6.1.2.1.34.7.1.1
ebnIsRscv .1.3.6.1.2.1.34.7.1.2
ebnDirConfig .1.3.6.1.2.1.34.7.1.3
ebnCOS .1.3.6.1.2.1.34.7.1.4
ebnSubnetRoutingList .1.3.6.1.2.1.34.7.1.5
hbn .1.3.6.1.2.1.34.7.1.6
ebnConformance .1.3.6.1.2.1.34.7.2
ebnCompliances .1.3.6.1.2.1.34.7.2.1
ebnGroups .1.3.6.1.2.1.34.7.2.2
Group
ebnDirectoryGroup .1.3.6.1.2.1.34.7.2.2.1
The EBN-related directory objects.
ebnIsRscvGroup .1.3.6.1.2.1.34.7.2.2.2
Two objects representing RSCV and class of service information saved by an EBN.
ebnDirectoryConfigGroup .1.3.6.1.2.1.34.7.2.2.3
The EBN Directory Configuration Group.
ebnCosMappingGroup .1.3.6.1.2.1.34.7.2.2.4
The EBN COS Mapping Group.
ebnSubnetRoutingListGroup .1.3.6.1.2.1.34.7.2.2.5
The Subnet Routing List Group.
hbnIsInGroup .1.3.6.1.2.1.34.7.2.2.6
The HBN-related Intermediate Session Objects.