CISCO-WAN-CES-RSRC-PART-MIB.mib object view, vendor Stratacom
Introduction
Most network devices and programs ship with so-called MIB files to describe the parameters and meanings (i.e.: friendly names) which are available for monitoring via SNMP.
ActiveXperts Network Monitor 2024 can import vendor-specific MIB files, so it can be used to monitor specific OID's (Object Identifiers).
This way, you can monitor your devices, computers, etc. by selecting your relevant OID's by name.
ActiveXperts Network Monitor 2024 can import MIB file CISCO-WAN-CES-RSRC-PART-MIB and use it to monitor vendor specific OID's.
CISCO-WAN-CES-RSRC-PART-MIB file content
Object view of CISCO-WAN-CES-RSRC-PART-MIB:
| Scalar Object |
| cesmPortCnfResPartGrpEntry |
.1.3.6.1.4.1.351.110.5.3.1.2.1.1 |
|
An entry for a resource partition. A resource
partition have to be created before connections
can be added to the logical ports.
|
| Tabular Object |
| cesmResPartPortNum |
.1.3.6.1.4.1.351.110.5.3.1.2.1.1.1 |
|
The value of this object identifies the CES port.
The value of this object must be same as the value
of 'cesPortNum' from cesmPortCnfGrpTable.
|
| cesmResPartCtrlrNum |
.1.3.6.1.4.1.351.110.5.3.1.2.1.1.2 |
|
This object identifies the controller
which can be used for accessing the resources.
The possible values are :
par(1) : Portable Auto Route controller.
: This value is applicable in Release 1.x.
pnni(2): PNNI Controller.
: This value is applicable in Release 2.x.
tag(3) : MPLS(Formerly known as Tag Switch)Controller
|
| cesmResPartRowStatus |
.1.3.6.1.4.1.351.110.5.3.1.2.1.1.3 |
|
This object is used for adding/deleting/modifying
resource partition on a CES port.
In MGX Release 1.x:
To add an entry, this object should be set to
add(1), value for other objects should not be
specified.
In MGX Release 2.x:
To add an entry, this object should be set to add(1).
To delete an entry, this object has to be set to del(2).
The resource partition can be deleted only after
deleting all the connections (LCNs).
|
| cesmResPartNumOfLcnAvail |
.1.3.6.1.4.1.351.110.5.3.1.2.1.1.4 |
|
This represents number of LCNs available for this
controller and this port.
In CESM-T3/E3 and 8-T1/E1,this value is 1.
|
| cesmResPartLcnLow |
.1.3.6.1.4.1.351.110.5.3.1.2.1.1.5 |
|
This represents low end of reserved LCN
In CESM-8T1/E1 and T3/E3, this refers to the
logical port.
|
| cesmResPartLcnHigh |
.1.3.6.1.4.1.351.110.5.3.1.2.1.1.6 |
|
This represents high end of reserved LCN
In CESM-8T1/E1 and T3/E3, this refers to the
logical port.
|
| cesmResPartIngrPctBW |
.1.3.6.1.4.1.351.110.5.3.1.2.1.1.7 |
|
The percentage of total ingress bandwidth reserved.
In CESM-8T1/E1 and T3/E3, as
there is only one LCN per port and it could be
used by only one controller,this value is
100% for that controller.
|
| cesmResPartEgrPctBW |
.1.3.6.1.4.1.351.110.5.3.1.2.1.1.8 |
|
The percentage of total egress bandwidth reserved
In CESM-8T1/E1 and T3/E3, as
there is only one LCN per port and it could be
used by only one controller,this value is
100% for that controller.
|
| cesmResPartCtrlrID |
.1.3.6.1.4.1.351.110.5.3.1.2.1.1.9 |
|
This is the controller identifier for the resource patition.
The default value is set for PNNI controller.
|
| Table |
| cesmPortCnfResPartGrpTable |
.1.3.6.1.4.1.351.110.5.3.1.2.1 |
|
This table is for configuring the resource partition
parameters.
|
| Object Identifier |
| ciscoWanCesRsrcPartMIB |
.1.3.6.1.4.1.351.150.41 |
|
The mib module to configure the resource
partition on Circuit Emulation Service(CES)
ports. This is applicable for service modules
providing the Circuit Emulation Services.
|
| cesmPortCnfResPartGrp |
.1.3.6.1.4.1.351.110.5.3.1.2 |
| cwcRsrcPartMIBConformance |
.1.3.6.1.4.1.351.150.41.2 |
| cwcRsrcPartMIBCompliances |
.1.3.6.1.4.1.351.150.41.2.1 |
| cwcRsrcPartMIBGroups |
.1.3.6.1.4.1.351.150.41.2.2 |
| Group |
| ciscoWanCesRsrcPartGroup |
.1.3.6.1.4.1.351.150.41.2.2.1 |
|
A collection of objects providing the
resource partition configuration on CES
ports.
|
