| wfAsrBaseCreate |
.1.3.6.1.4.1.18.3.5.9.11.1.1 |
|
Create/Delete parameter. Default is created.
Users perform a set operation on this
object in order to create/delete ASR.
|
| wfAsrBaseEnable |
.1.3.6.1.4.1.18.3.5.9.11.1.2 |
|
Enable/Disable parameter. Default is enabled.
Users perform a set operation on this
object in order to enable/disable ASR.
|
| wfAsrBaseState |
.1.3.6.1.4.1.18.3.5.9.11.1.3 |
|
The current state of the entire ASR.
|
| wfAsrNextHopRetryLimit |
.1.3.6.1.4.1.18.3.5.9.11.1.4 |
|
Set the number of next hop entries to try to establish
the SVC should the first next hop entry fail.
|
| wfAsrSecureInFilter |
.1.3.6.1.4.1.18.3.5.9.11.1.5 |
|
Enable or disable inbound packet filtering.
This object will be implemented as part of the
follow on project.
|
| wfAsrSecureInValid |
.1.3.6.1.4.1.18.3.5.9.11.1.6 |
|
Enable or disable inbound call validation. This object will
be implemented as part of a follow on project.
|
| wfAsrHoldDownTimer |
.1.3.6.1.4.1.18.3.5.9.11.1.7 |
|
The hold down timer is used to prevent retries to a destination
that the SVC setup process has failed on. This value would be
used if filter/flow spec information is not returned from NHS.
|
| wfAsrActiveSvcs |
.1.3.6.1.4.1.18.3.5.9.11.1.8 |
|
A count of the SVCs currently active on this router slot.
|
| wfAsrFwdTblEntries |
.1.3.6.1.4.1.18.3.5.9.11.1.9 |
|
A count of entries in the ASR forward table.
|
| wfAsrFwdTblSeq |
.1.3.6.1.4.1.18.3.5.9.11.1.10 |
|
Sequence number used to determine changes to the ASR forward
table.
|
| wfAsrDnsProxyPort |
.1.3.6.1.4.1.18.3.5.9.11.1.11 |
|
DNS proxy port for QOS translation queries
|
| wfAsrMaxSessions |
.1.3.6.1.4.1.18.3.5.9.11.1.12 |
|
Maximum number of TCP/IP sessions which are to be managed by ASR.
|
| wfAsrDebugLevel |
.1.3.6.1.4.1.18.3.5.9.11.1.13 |
|
Debug level in which to enable log messages. The
greater the value, the more detailed the log messages.
|
| wfAsrUseDynRdiscPref |
.1.3.6.1.4.1.18.3.5.9.11.1.14 |
|
Enable/Disable parameter for ASR to update
the Dynamic Router Discovery Preference value.
If enabled, wfRdiscInterfacePref must be 0 in
order to advertise the ASR Dynamic Preference.
|
| wfAsrX213PriEntry |
.1.3.6.1.4.1.18.3.5.9.11.2.1 |
|
X.213 conversion table.
|
| wfAsrRtrPriEntry |
.1.3.6.1.4.1.18.3.5.9.11.3.1 |
|
Router priority conversion table.
|
| wfAsrMultiHopEntry |
.1.3.6.1.4.1.18.3.5.9.11.4.1 |
|
Multi Hop PVC identification.
|
| wfAsrDirectExceptEntry |
.1.3.6.1.4.1.18.3.5.9.11.5.1 |
|
The ASR directional exception table.
|
| wfAsrCircuitEntry |
.1.3.6.1.4.1.18.3.5.9.11.6.1 |
|
An ASR circuit description
|
| wfAsrFiltEntry |
.1.3.6.1.4.1.18.3.5.9.11.7.1 |
|
ASR SVC setup information.
|
| wfAsrTestCreate |
.1.3.6.1.4.1.18.3.5.9.11.8.1 |
|
Create/Delete parameter. Default is created.
Users perform a set operation on this
object in order to create/delete ASR Test Object.
|
| wfAsrTestChangeVal |
.1.3.6.1.4.1.18.3.5.9.11.8.2 |
|
Value to set the protocol field in the ASR
Fwd Table. This will take the SVC entry
matching the Dlci and Cct number and change
the filter. This is used only for Inbound Pkt
Filtering tests
|
| wfAsrTestDlci |
.1.3.6.1.4.1.18.3.5.9.11.8.3 |
|
Dlci of SVC Filter entry to change
|
| wfAsrTestCct |
.1.3.6.1.4.1.18.3.5.9.11.8.4 |
|
Circuit number of SVC Filter to change
|
| wfAsrX213PriLowVal |
.1.3.6.1.4.1.18.3.5.9.11.2.1.2 |
|
Low value of X.213 priority range.
|
| wfAsrX213PriHiVal |
.1.3.6.1.4.1.18.3.5.9.11.2.1.3 |
|
High value of X.213 priority range.
|
| wfAsrX213PriDelete |
.1.3.6.1.4.1.18.3.5.9.11.2.1.1 |
|
Create/delete indicator for X.213 priority table entry.
|
| wfAsrX213PriSwVal |
.1.3.6.1.4.1.18.3.5.9.11.2.1.4 |
|
Switch specific X.213 priority value.
|
| wfAsrRtrPriLowVal |
.1.3.6.1.4.1.18.3.5.9.11.3.1.2 |
|
Low value of router priority range.
|
| wfAsrRtrPriHiVal |
.1.3.6.1.4.1.18.3.5.9.11.3.1.3 |
|
High value of router priority range.
|
| wfAsrRtrPriDelete |
.1.3.6.1.4.1.18.3.5.9.11.3.1.1 |
|
Create/delete indicator for Router priority table entry.
|
| wfAsrRtrPriCvtVal |
.1.3.6.1.4.1.18.3.5.9.11.3.1.4 |
|
Router priority Queue value.
|
| wfAsrMhCircuitNumber |
.1.3.6.1.4.1.18.3.5.9.11.4.1.2 |
|
Instance identifier. The circuit number of this interface.
|
| wfAsrMhVcid1 |
.1.3.6.1.4.1.18.3.5.9.11.4.1.3 |
|
VCID 1 value. The Dlci number for Frame Relay, the VPI for ATM.
|
| wfAsrMhVcid2 |
.1.3.6.1.4.1.18.3.5.9.11.4.1.4 |
|
VCID 2 value. The VCI for ATM, NULL for Frame Relay.
|
| wfAsrMultiHopDelete |
.1.3.6.1.4.1.18.3.5.9.11.4.1.1 |
|
Create/delete indicator for multi hop table entry.
|
| wfAsrServiceProtocol |
.1.3.6.1.4.1.18.3.5.9.11.5.1.1 |
|
Service protocol indicates what protocol this entry is
for. Coices are UDP or TCP.
|
| wfAsrServicePort |
.1.3.6.1.4.1.18.3.5.9.11.5.1.2 |
|
Application port number of service connecting to.
|
| wfAsrSrcPortLow |
.1.3.6.1.4.1.18.3.5.9.11.5.1.3 |
|
Low port number of application serving as source used
at host site.
|
| wfAsrSrcPortHigh |
.1.3.6.1.4.1.18.3.5.9.11.5.1.4 |
|
High port number of application serving as source used
at host site.
|
| wfAsrDestPortLow |
.1.3.6.1.4.1.18.3.5.9.11.5.1.5 |
|
Low port number of application serving as destination used
at client site.
|
| wfAsrDestPortHigh |
.1.3.6.1.4.1.18.3.5.9.11.5.1.6 |
|
High port number of application serving as destination used
at client site.
|
| wfAsrCircuitNumber |
.1.3.6.1.4.1.18.3.5.9.11.6.1.4 |
|
Instance identifier. The circuit number of this interface.
|
| wfAsrCircuitCreate |
.1.3.6.1.4.1.18.3.5.9.11.6.1.1 |
|
Create/Delete parameter. Default is created.
Users perform a set operation on this
object in order to create/delete an ASR circuit.
|
| wfAsrCircuitEnable |
.1.3.6.1.4.1.18.3.5.9.11.6.1.2 |
|
Enable/Disable parameter. Default is enabled.
Users perform a set operation on this
object in order to enable/disable an ASR circuit.
|
| wfAsrCircuitState |
.1.3.6.1.4.1.18.3.5.9.11.6.1.3 |
|
Invalid indicates an error in processing the cfg record
|
| wfAsrCircuitCallCtrl |
.1.3.6.1.4.1.18.3.5.9.11.6.1.5 |
|
Define call policy for this SVC circuit. 1) allow inbound calls only 2) allow outbound calls only 3)allow inbound and outbound calls 4) allow neither inbound or outbound calls.
|
| wfAsrCircuitInReceives |
.1.3.6.1.4.1.18.3.5.9.11.6.1.6 |
|
The total number of input datagrams received at the circuit,
including those received in error.
|
| wfAsrCircuitInDiscards |
.1.3.6.1.4.1.18.3.5.9.11.6.1.7 |
|
The total number of input datagrams discarded due to failed
setup attempts, unreachable destinations, etc.
|
| wfAsrCircuitSetupRequests |
.1.3.6.1.4.1.18.3.5.9.11.6.1.8 |
|
The total number of SVC setup requests attempted on the circuit
,
including those which failed.
|
| wfAsrCircuitSetupSucc |
.1.3.6.1.4.1.18.3.5.9.11.6.1.9 |
|
The total number of SVC setup requests attempted on the circuit
which resulted in an SVC being established.
|
| wfAsrCircuitSetupFail |
.1.3.6.1.4.1.18.3.5.9.11.6.1.10 |
|
The total number of SVC setup requests attempted on the circuit
which resulted in an SVC not being established.
|
| wfAsrCircuitSVCsEstablished |
.1.3.6.1.4.1.18.3.5.9.11.6.1.11 |
|
The total number of SVCs currently established on the circuit.
|
| wfAsrNegativeNHR |
.1.3.6.1.4.1.18.3.5.9.11.6.1.12 |
|
Count of negative NHR responses received from NHRP.
|
| wfAsrSvcOutboundReqFail |
.1.3.6.1.4.1.18.3.5.9.11.6.1.13 |
|
Count of outbound requests for SVCs that failed.
|
| wfAsrSvcInboundFilterFail |
.1.3.6.1.4.1.18.3.5.9.11.6.1.14 |
|
Count of inbound packets failing inbound packet filtering.
|
| wfAsrSvcInboundCallValFail |
.1.3.6.1.4.1.18.3.5.9.11.6.1.15 |
|
Count of inbound SVC call validation failures.
|
| wfAsrFilterSlot |
.1.3.6.1.4.1.18.3.5.9.11.7.1.2 |
|
The router slot on which this filter exists.
|
| wfAsrDestIpAddr |
.1.3.6.1.4.1.18.3.5.9.11.7.1.3 |
|
Filter destination IP address reference value.
|
| wfAsrDestIpMask |
.1.3.6.1.4.1.18.3.5.9.11.7.1.4 |
|
Filter destination IP address mask.
|
| wfAsrSourceIpAddr |
.1.3.6.1.4.1.18.3.5.9.11.7.1.5 |
|
Filter source IP address reference value.
|
| wfAsrSourceIpMask |
.1.3.6.1.4.1.18.3.5.9.11.7.1.6 |
|
Filter source IP address mask.
|
| wfAsrDestPortRangeLow |
.1.3.6.1.4.1.18.3.5.9.11.7.1.7 |
|
The low value for the range of TCP/UDP destination ports.
|
| wfAsrDestPortRangeHigh |
.1.3.6.1.4.1.18.3.5.9.11.7.1.8 |
|
The high value for the range of TCP/UDP destination ports.
|
| wfAsrSourcePortRangeLow |
.1.3.6.1.4.1.18.3.5.9.11.7.1.9 |
|
The low value for the range of TCP/UDP source ports.
|
| wfAsrSourcePortRangeHigh |
.1.3.6.1.4.1.18.3.5.9.11.7.1.10 |
|
The high value for the range of TCP/UDP source ports.
|
| wfAsrIPProtocol |
.1.3.6.1.4.1.18.3.5.9.11.7.1.11 |
|
IP protocol for this filter (TCP or UDP).
|
| wfAsrFilterCreate |
.1.3.6.1.4.1.18.3.5.9.11.7.1.1 |
|
Create/delete this filter entry.
|
| wfAsrFilterTtl |
.1.3.6.1.4.1.18.3.5.9.11.7.1.12 |
|
For SVC filters, this is the SVC idle time (seconds).
For all other filter types, this is the filter expiration
time (seconds).
|
| wfAsrFilterType |
.1.3.6.1.4.1.18.3.5.9.11.7.1.13 |
|
Type of filter (SVC, NOSVC, in-progress, dest unreachable).
|
| wfAsrSvcCircuitNumber |
.1.3.6.1.4.1.18.3.5.9.11.7.1.14 |
|
Circuit number on which the SVC is created.
|
| wfAsrSvcVcid1 |
.1.3.6.1.4.1.18.3.5.9.11.7.1.15 |
|
For Frame Relay SVCs, this is the DLCI value.
For ATM SVCs, this is the VPI value.
|
| wfAsrSvcVcid2 |
.1.3.6.1.4.1.18.3.5.9.11.7.1.16 |
|
For ATM SVCs, this is the VCI value.
|
| wfAsrSvcCalledAddr |
.1.3.6.1.4.1.18.3.5.9.11.7.1.17 |
|
SVC Called Party Address
|
| wfAsrSvcSetupTime |
.1.3.6.1.4.1.18.3.5.9.11.7.1.18 |
|
Time stamp of when the SVC was created.
|
| wfAsrSvcType |
.1.3.6.1.4.1.18.3.5.9.11.7.1.19 |
|
Type of SVC created (Frame Relay or ATM).
|
| wfAsrSvcMTU |
.1.3.6.1.4.1.18.3.5.9.11.7.1.20 |
|
The maximum transmission unit for this SVC.
|
| wfAsrSvcRouterPriOut |
.1.3.6.1.4.1.18.3.5.9.11.7.1.21 |
|
The router priority queue to be used for the packets
sent on this SVC.
|
| wfAsrFrSvcCIRIn |
.1.3.6.1.4.1.18.3.5.9.11.7.1.22 |
|
Frame Relay SVC commited information rate - inbound (bps).
|
| wfAsrFrSvcCIROut |
.1.3.6.1.4.1.18.3.5.9.11.7.1.23 |
|
Frame Relay SVC commited information rate - outbound (bps).
|
| wfAsrFrSvcBCIn |
.1.3.6.1.4.1.18.3.5.9.11.7.1.24 |
|
Frame Relay commited burst rate for SVC - inbound (bps).
|
| wfAsrFrSvcBCOut |
.1.3.6.1.4.1.18.3.5.9.11.7.1.25 |
|
Frame Relay commited burst rate for the SVC - outbound (bps).
|
| wfAsrFrSvcBEIn |
.1.3.6.1.4.1.18.3.5.9.11.7.1.26 |
|
Frame Relay excess burst rate for the SVC - inbound (bps).
|
| wfAsrFrSvcBEOut |
.1.3.6.1.4.1.18.3.5.9.11.7.1.27 |
|
Frame Relay excess burst rate for the SVC - outbound (bps).
|
| wfAsrFrSvcX213Pri |
.1.3.6.1.4.1.18.3.5.9.11.7.1.28 |
|
Frame Relay SVC X.213 data priority value passed
to the switch during call setup.
|
| wfAsrAtmSvcPCRIn |
.1.3.6.1.4.1.18.3.5.9.11.7.1.29 |
|
ATM SVC Peak Cell Rate - inbound.
|
| wfAsrAtmSvcPCROut |
.1.3.6.1.4.1.18.3.5.9.11.7.1.30 |
|
ATM SVC Peak Cell Rate - outbound.
|
| wfAsrAtmSvcSCRIn |
.1.3.6.1.4.1.18.3.5.9.11.7.1.31 |
|
ATM SVC Sustainable Cell Rate - inbound.
|
| wfAsrAtmSvcSCROut |
.1.3.6.1.4.1.18.3.5.9.11.7.1.32 |
|
ATM SVC Sustainable Cell Rate - outbound.
|
| wfAsrAtmSvcMBSIn |
.1.3.6.1.4.1.18.3.5.9.11.7.1.33 |
|
ATM SVC Maximum Burst Size - inbound.
|
| wfAsrAtmSvcMBSOut |
.1.3.6.1.4.1.18.3.5.9.11.7.1.34 |
|
ATM SVC Maximum Burst Size - outbound.
|
| wfAsrAtmSvcQOSClassIn |
.1.3.6.1.4.1.18.3.5.9.11.7.1.35 |
|
ATM SVC Quality of Service - inbound. Class 0 through 4.
|
| wfAsrAtmSvcQOSClassOut |
.1.3.6.1.4.1.18.3.5.9.11.7.1.36 |
|
ATM SVC Quality of Service - outbound. Class 0 through 4.
|
| wfAsrAtmSvcCDVTIn |
.1.3.6.1.4.1.18.3.5.9.11.7.1.37 |
|
ATM SVC Cell Delay Variation Tolerance - inbound.
|
| wfAsrAtmSvcCDVTOut |
.1.3.6.1.4.1.18.3.5.9.11.7.1.38 |
|
ATM SVC Cell Delay Variation Tolerance - outbound.
|
| wfAsrAtmSvcCLRIn |
.1.3.6.1.4.1.18.3.5.9.11.7.1.39 |
|
ATM SVC Cell Loss Ratio - inbound.
|
| wfAsrAtmSvcCLROut |
.1.3.6.1.4.1.18.3.5.9.11.7.1.40 |
|
ATM SVC Cell Loss Ratio - outbound.
|
