| wfDs3E3ConfigLineIndex |
.1.3.6.1.4.1.18.3.4.26.10.1.5 |
|
this corresponds to the Wellfleet circuit number
|
| wfDs3E3ConfigDelete |
.1.3.6.1.4.1.18.3.4.26.10.1.1 |
|
Create/Delete parameter
|
| wfDs3E3ConfigDisable |
.1.3.6.1.4.1.18.3.4.26.10.1.2 |
|
Enable/Disable parameter
|
| wfDs3E3ConfigState |
.1.3.6.1.4.1.18.3.4.26.10.1.3 |
|
State of the DS3 Port.
|
| wfDs3E3ConfigLastChange |
.1.3.6.1.4.1.18.3.4.26.10.1.4 |
|
The value of sysUpTime at the time the interface entered
its current operational state.
|
| wfDs3E3ConfigIfIndex |
.1.3.6.1.4.1.18.3.4.26.10.1.6 |
|
this is value of ifIndex from the Interfaces table of
MIB II (RFC 1213).
|
| wfDs3E3ConfigLineType |
.1.3.6.1.4.1.18.3.4.26.10.1.7 |
|
the variety of DS3/E3 application implementing this circuit
|
| wfDs3E3ConfigLineCoding |
.1.3.6.1.4.1.18.3.4.26.10.1.8 |
|
the variety of Zero Code Suppression used on the link
|
| wfDs3E3ConfigLoopbackConfig |
.1.3.6.1.4.1.18.3.4.26.10.1.9 |
|
the loopback configuration of the DS3/E3 interface
|
| wfDs3E3ConfigLineStatus |
.1.3.6.1.4.1.18.3.4.26.10.1.10 |
|
the status of the DS3/E3 line
|
| wfDs3E3ConfigPrimaryClockSource |
.1.3.6.1.4.1.18.3.4.26.10.1.11 |
|
Selects the Primary source of the Tx Clock for the DS3/E3
interface
|
| wfDs3E3ConfigSecondaryClockSource |
.1.3.6.1.4.1.18.3.4.26.10.1.12 |
|
Selects the Secondary source of the Tx Clock for the DS3/E3
interface
|
| wfDs3E3ConfigMtu |
.1.3.6.1.4.1.18.3.4.26.10.1.13 |
|
MTU parameter for all channels on DS3 .
|
| wfDs3E3ConfigLineBuildOut |
.1.3.6.1.4.1.18.3.4.26.10.1.14 |
|
Set according to cable length, short (less than 225 feet)
or long (greater than 225 feet).
|
| wfDs3E3ConfigCurrentClock |
.1.3.6.1.4.1.18.3.4.26.10.1.15 |
|
Indicates the clock source currently in use by the DS1
|
| wfDs3E3ConfigExtClockOperational |
.1.3.6.1.4.1.18.3.4.26.10.1.16 |
|
Indicates whether the External clock is operational
|
| wfDs3E3ConfigSetupAlarmThreshold |
.1.3.6.1.4.1.18.3.4.26.10.1.17 |
|
Specifies setup time for performance failure conditions,
in seconds. When a performance defect is present for greater
than the time specified by this parameter a performance
failure is registered and a message is logged.
|
| wfDs3E3ConfigClearAlarmThreshold |
.1.3.6.1.4.1.18.3.4.26.10.1.18 |
|
Specifies clear time for performance failure conditions,
in seconds. When a performance failure condition has been
cleared for greater than the time specified by this parameter
then the failure cleared condition is registered and a
message is logged.
|
| wfDs3E3ConfigLoopbackState |
.1.3.6.1.4.1.18.3.4.26.10.1.19 |
|
Indicates the current loopback state of this interface.
The interface can be in one the following states:
Line Loopback
Payload Loopback
no loopback
Loopback modes can be initiated by either of two methods:
Manager requested Loopback is initiated by the Manager of
this device.
Network requested Loopback is initiated by this interface
receiving an in-band request on the network from the far
end device.
|
| wfDs3E3ConfigSendCode |
.1.3.6.1.4.1.18.3.4.26.10.1.20 |
|
This variable is currently read-only and it indicates what type of code has
been sent across the DS3 interface by the device. The values mean:
SENDNOCODE - sending looped or normal data
SENDLINECODE - sending a request for a line loopback
SENDPAYLOADCODE - sending a request for a payload loopback
SENDDS1LOOPCODE - sending a request for a DS1 loopback
|
| wfDs3E3ActionPortLineNumber |
.1.3.6.1.4.1.18.3.4.26.17.1.1 |
|
Instance ID LineNumber, filled in by driver
|
| wfDs3E3ActionSendFeacLoopCode |
.1.3.6.1.4.1.18.3.4.26.17.1.2 |
|
Selects a Far End Alarm and Control Channel code to be
sent to the remote end.
|
| wfDs3E3ActionSendFeacDs1LoopUpCode |
.1.3.6.1.4.1.18.3.4.26.17.1.3 |
|
Selects Loop Up code to be sent to the remote end for a DS1.
Value passed through this attribute is the DS1 Port number
(1 through 28).
|
| wfDs3E3ActionSendFeacDs1LoopDownCode |
.1.3.6.1.4.1.18.3.4.26.17.1.4 |
|
Selects Loop Down code to be sent to the remote end for a DS1.
Value passed through this attribute is the DS1 Port number
(1 through 28).
|
| wfDs3E3ActionClearCurrentStats |
.1.3.6.1.4.1.18.3.4.26.17.1.5 |
|
Clears this port's Current 15 minute Statistics.
|
| wfDs3E3ActionClearFarEndCurrentStats |
.1.3.6.1.4.1.18.3.4.26.17.1.6 |
|
Clears this port's Far End, Current 15 minute Statistics.
|
| wfDs3E3ActionClearDayCurrentStats |
.1.3.6.1.4.1.18.3.4.26.17.1.7 |
|
Clears this port's Current Day Statistics.
|
| wfDs3E3ActionClearFarEndDayCurrentStats |
.1.3.6.1.4.1.18.3.4.26.17.1.8 |
|
Clears this port's Far End, Current Day Statistics.
|
| wfDs3E3ActionClearIntervalStats |
.1.3.6.1.4.1.18.3.4.26.17.1.9 |
|
Clears All Interval Statistics (15 minute and day) of this port.
|
| wfDs3E3ActionClearFarEndIntervalStats |
.1.3.6.1.4.1.18.3.4.26.17.1.10 |
|
Clears All Far End Interval Statistics (15 minute and day) of this port.
|
