| wfDsuCsuIfSlot |
.1.3.6.1.4.1.18.3.4.30.1.1.2 |
|
Instance ID Slot, filled in by driver
|
| wfDsuCsuIfConnector |
.1.3.6.1.4.1.18.3.4.30.1.1.3 |
|
Instance ID Connector, filled in by the driver.
|
| wfDsuCsuIfDelete |
.1.3.6.1.4.1.18.3.4.30.1.1.1 |
|
Create/Delete parameter
|
| wfDsuCsuSoftRev |
.1.3.6.1.4.1.18.3.4.30.1.1.4 |
|
Displays the Software Revision of the DSU CSU card.
|
| wfDsuCsuHardRev |
.1.3.6.1.4.1.18.3.4.30.1.1.5 |
|
Displays the Hardware Revision of the DSU CSU card.
|
| wfDsuCsuOpMode |
.1.3.6.1.4.1.18.3.4.30.1.1.6 |
|
Identifies the type of telco service that the
DSU CSU is connected to. Opmode should be set
to dds1-56kbps (1) when connected to a DDS1 56 Kbps
line. Opmode should be set to cc-64kbps (2) when
connected to a Clear Channel 64Kbps line.
|
| wfDsuCsuTxClkSelect |
.1.3.6.1.4.1.18.3.4.30.1.1.7 |
|
Default timing, or clock, source for transmiting data to the
network. There must be only one source on a DDS line.
Timing should always be slave (1) when connected to a
network. Timing should be set to master (2) on either
end of a private-wire configuration, with the other end
being set to slave (1).
|
| wfDsuCsuUnitReset |
.1.3.6.1.4.1.18.3.4.30.1.1.8 |
|
Enables the operator to remotely reset the unit.
Using this command will cause the unit to terminate
all its connections and drop data.
|
| wfDsuCsu64KTxMonitor |
.1.3.6.1.4.1.18.3.4.30.1.1.9 |
|
This signal is used in 64K Clear Channel mode to suppress
customer data in the event that the data duplicates a
network control code. A setting of enabled(1) suppresses
customer data. A setting of disabled(2) allows all customer
data through, which could
potentially put the other end into a loop if the data
duplicates a network control code.
|
| wfDsuCsuOpState |
.1.3.6.1.4.1.18.3.4.30.1.1.10 |
|
Indicates the current operating state of the DSU CSU card.
|
| wfDsuCsuServiceStatus |
.1.3.6.1.4.1.18.3.4.30.1.1.11 |
|
The Current status of the physical interface.
Your network carrier can send Out-of-Service
or Maintenance Mode codes.
|
| wfDsuCsuV54Lpbk |
.1.3.6.1.4.1.18.3.4.30.1.1.12 |
|
Enables the operator to control, and examine the
state of, V.54 loopbacks within the DSU CSU.
|
| wfDsuCsuV54Timer |
.1.3.6.1.4.1.18.3.4.30.1.1.13 |
|
Duration in seconds that a test specified in wfDsuCsuTestLpbk
is to execute.
|
| wfDsuCsuV54Errors |
.1.3.6.1.4.1.18.3.4.30.1.1.14 |
|
Indicates the number of errors reported during the last
loopback test. This count will only be updated for
loopbacks with test pattern.
|
| wfDsuCsuCqmsLaWindow |
.1.3.6.1.4.1.18.3.4.30.1.1.15 |
|
Indicates the number of minutes within the window in which
the availability of the line (network) is to be calculated. The
availability of the line is an indication of the percentage
of time the line has been in service.
It is calculated as follows:
(((wfDsuCsuCqmsLaWindow*60) - (wfDsuCsuCqmsLaErrCnt*wfDsuCsuCqmsLaPollRate))/
wfDsuCsuCqmsLaWindow*60)
|
| wfDsuCsuCqmsLaErrors |
.1.3.6.1.4.1.18.3.4.30.1.1.16 |
|
Indicates the total number of seconds that the line was not
in service in the last window of size wfDsuCsuCqmsLaWindow.
|
| wfDsuCsuCqmsLaPollRate |
.1.3.6.1.4.1.18.3.4.30.1.1.17 |
|
Indicates the number of seconds between polls for line status
from the DsuCsu. A value of 1 forces polling every second.
A value of 60 forces polling every minute.
|
| wfDsuCsuCqmsReset |
.1.3.6.1.4.1.18.3.4.30.1.1.18 |
|
Resets the CQMS counters to their default values. For
Line Availability, wfDsuCsuCqmsLaErrCnt is reset.
|
| wfDsuCsuOOSErrors |
.1.3.6.1.4.1.18.3.4.30.1.1.19 |
|
The number of seconds in which Out of Service control codes
were received from the Telco. The counter is incremented
whenever a sample within a second indicated the unit received
an out of service control code.
|
| wfDsuCsuFrameErrors |
.1.3.6.1.4.1.18.3.4.30.1.1.20 |
|
The number of seconds in which the unit was out of frame
with the Telco. This is only applicable in 64K mode. The
counter is incremented whenever a sample within a second
indicated the unit was out of frame.
|
| wfDsuCsuLOLErrors |
.1.3.6.1.4.1.18.3.4.30.1.1.21 |
|
The number of seconds in which the unit has detected that no
signal is present on the line, and/or no line is present.
|
| wfDsuCsuInitState |
.1.3.6.1.4.1.18.3.4.30.1.1.22 |
|
Indictes the state of the DSU/CSU initialization sequence. The state will
indicate if the DSU/CSU has been initialized and is in the *monitor*
state polling the card for line condition, or in the *loopback state
running a user-initiated loopback
|
