| wfDvmrpBaseCreate |
.1.3.6.1.4.1.18.3.5.3.12.1.1 |
|
This entry will provide the base configuration for the DVMRP
multicast support on the router.
|
| wfDvmrpBaseEnable |
.1.3.6.1.4.1.18.3.5.3.12.1.2 |
|
Enable or disable DVMRP support in router
|
| wfDvmrpBaseState |
.1.3.6.1.4.1.18.3.5.3.12.1.3 |
|
State of DVMRP base module
|
| wfDvmrpBaseFullUpdateInterval |
.1.3.6.1.4.1.18.3.5.3.12.1.4 |
|
Full update interval. This value specifies, in seconds, how
often routing messages containing complete routing tables are
sent.
|
| wfDvmrpBaseTriggeredUpdateInterval |
.1.3.6.1.4.1.18.3.5.3.12.1.5 |
|
Triggered update interval. This value specifies, in seconds,
how often triggered routing messages are sent; this represents
the minimum amount of time between these type of messages.
Triggered updates are sent between full update; the timers
restart when a full update is sent so this value should be less
than the full update rate.
|
| wfDvmrpBaseLeafTimeout |
.1.3.6.1.4.1.18.3.5.3.12.1.6 |
|
Leaf timeout. This value specifies, in seconds, the
virtual interface hold down timer.
|
| wfDvmrpBaseNeighborTimeout |
.1.3.6.1.4.1.18.3.5.3.12.1.7 |
|
Neighbor timeout. This value specifies, in seconds, how
long a router neighbor is considered 'up' without confirmation.
|
| wfDvmrpBaseRouteExpirationTimeout |
.1.3.6.1.4.1.18.3.5.3.12.1.8 |
|
Route Expiration timeout. This value specifies, in
seconds, how long a route is considered valid without
confirmation; this represents the duration of time that this
route will be used.
|
| wfDvmrpBaseGarbageTimeout |
.1.3.6.1.4.1.18.3.5.3.12.1.9 |
|
Garbage timeout. This value specifies, in seconds, how
long a route exists without confirmation; this represents the
duration of time that this route will be included in routing
updates. This value must be greater than the route expiration
timeout.
|
| wfDvmrpBaseEstimatedRoutes |
.1.3.6.1.4.1.18.3.5.3.12.1.10 |
|
Estimated number of routes, per slot. This is used for
pre-allocating routing tables. Note that routes are kept on a
per-source network basis, independent of multicast group. This number
must include a route for every local network that has a CCT configured
for multicasting.
|
| wfDvmrpBaseNeighborProbeInterval |
.1.3.6.1.4.1.18.3.5.3.12.1.11 |
|
Neighbor probe interval: how often to send a probe on VIFs
|
| wfDvmrpBaseRouteSwitchTimeout |
.1.3.6.1.4.1.18.3.5.3.12.1.12 |
|
Route switch timeout. How long to wait, without receiving a subsequent route update
from the original neighbor, before switching to a different neighbor.
|
| wfDvmrpBaseActualRoutes |
.1.3.6.1.4.1.18.3.5.3.12.1.13 |
|
Count of number of entries currently in route table
|
| wfDvmrpBaseDebugLevel |
.1.3.6.1.4.1.18.3.5.3.12.1.14 |
|
Turn DVMRP log ON or OFF for DVMRP debuging messages
The levels are:
NO_DISPLAY_LOG 0x0001 - Reserved
ROUTE_UPDATE_LOG 0x0002 - Displays all routing table events
CACHE_ADD_LOG 0x0004 - Displays events relating to addition of
cache entry by the cache gate
CACHE_DELETE_LOG 0x0008 - Displays all events relating to deletion
of cache entry
CACHE_CHANGE_LOG 0x0010 - Displays all events relating to updates of
cache entries
CACHE_DATA_LOG 0x0020 - obsolete
PRUNE_MSG_LOG 0x0040 - Display router received pruning related
messages, including prunes, grafts,
graft_acks, and neighbor reset
PRUNE_XMIT_LOG 0x0080 - Display a messaged when a initial prune
state is established for a (src, group).
IGMP_COM_LOG 0x0100 - Display communication events between IGMP
and DVMRP, events including some hosts
joining a group, and all hosts leaving a
group.
DVMRP_XMIT_LOG 0x0200 - Display transmission events by the router,
e.g, prune, grafts...
CACHE_NO_GH_LOG 0x0400 - Display buffer forwarding to non-existing main or remote cache gate.
CACHE_DBG_LOG 0x0800 - Display general debugging messaages
MEM_DBG_LOG 0x1000 - Display dvmrp memory usage activities
INTEROP_DBG_LOG 0x2000 - Display dvmrp mospf debug
CACHE_BASE_ADD_LOG 0x4000 - Obsolete
CACHE_VIF_ADD_LOG 0x8000 - Obsolete
CACHE_BASE_DELETE_LOG 0x10000 - Obsolete
CACHE_VIF_DELETE_LOG 0x20000 - Obsolete
MTRACE_UPDATE_LOG 0x40000 - Displays mtrace update info
NEIGHBOR_UPDATE_LOG 0x80000 - Display events relating to
addition, deletion and update of
neighbor's info
MTM_INTERFACE_LOG 0x100000 - Display events relating to MTM-DVMRP
interface, events as MTM inbound,
outbound interact with DVMRP and entries
deletion/addition.
ROUTE_ADD_LOG 0x200000 -
ROUTE_DEL_LOG 0x400000 -
REMOTE_CACHE_ADD_LOG 0x800000 - Display addition event for the
outgoing interface of (source, group)
cache entry
REMOTE_CACHE_DELETE_LOG 0x1000000 - Display deletion event for the
outgoing interface of (source, group)
cache entry
RX_CONFLICT_ROUTE_INFO_LOG 0x2000000 - Display received conflict
route information
|
| wfDvmrpBasePruningEnable |
.1.3.6.1.4.1.18.3.5.3.12.1.15 |
|
Enable or Disable Pruning functionality at the Base level
|
| wfDvmrpBaseFragmentMtuThreshold |
.1.3.6.1.4.1.18.3.5.3.12.1.16 |
|
the default value is the CSMACD_MTU, and the MINiMUN is
X25_DDN_MTU. Both are taken from dp.h
|
| wfDvmrpBaseMaxRoutes |
.1.3.6.1.4.1.18.3.5.3.12.1.17 |
|
Max number of routes, per slot. This is used to limit
the size of routing tables. Note that routes are kept on a
per-source network basis, independent of multicast group. This number
must include a route for every local network that has a CCT configured
for multicasting.
|
| wfDvmrpBasePolicyEnable |
.1.3.6.1.4.1.18.3.5.3.12.1.18 |
|
Enable or Disable route policy functionality at the Base level
|
| wfDvmrpCircuitEntry |
.1.3.6.1.4.1.18.3.5.3.12.2.1 |
|
One instance of this object exists for every CCT that supports
this feature. The instance ID for this object will be the circuit
number.
|
| wfDvmrpTunnelEntry |
.1.3.6.1.4.1.18.3.5.3.12.3.1 |
|
This object is used to specify the set of 'multicast tunnels',
unicast pipes that are used to send IP multicast datagrams to
remote network multicast routers via intermediate routers that
may not support this style of IP multicasting. One instance of
this object exists for every separate tunnel destination. The
instance identifier is the IP address of the
remote router neighbor and the local circuit number.
|
| wfDvmrpRouteEntry |
.1.3.6.1.4.1.18.3.5.3.12.4.1 |
|
Supported by mib proxy. One entry exists for each active route.
|
| wfDvmrpRouteInterfaceEntry |
.1.3.6.1.4.1.18.3.5.3.12.5.1 |
|
Supported by mib proxy. One entry exists for each virtual interface on
an active route. It is associated with a route via the source network/
net mask fields. The instance ID includes tunnel ID, which is 0 for
non-tunnel interfaces.
|
| wfDvmrpNeighboringRouterEntry |
.1.3.6.1.4.1.18.3.5.3.12.6.1 |
|
This entry is used to indentify the known neighboring routers for
a circuit. This object will be indentified by circuit number,
tunnel id (to identify local interface), and the IP address of the neighbor.
|
| wfDvmrpCircuitCCT |
.1.3.6.1.4.1.18.3.5.3.12.2.1.4 |
|
This circuit number.
|
| wfDvmrpCircuitCreate |
.1.3.6.1.4.1.18.3.5.3.12.2.1.1 |
|
Create or delete
|
| wfDvmrpCircuitEnable |
.1.3.6.1.4.1.18.3.5.3.12.2.1.2 |
|
Enable or disable DVMRP on this circuit
|
| wfDvmrpCircuitState |
.1.3.6.1.4.1.18.3.5.3.12.2.1.3 |
|
The current state of the DVMRP interface. Invalid
indicates an error in processing the configuration record.
|
| wfDvmrpCircuitRouteEnable |
.1.3.6.1.4.1.18.3.5.3.12.2.1.5 |
|
Enable/disble this circuit for routing. If enabled, this
circuit will be used to propogate routing information,
information about this circuit will be incorporated into routing
updates, and multicast datagrams will be forwarded 'in native
mode' (e.g. as multicast datagrams) via this circuit. If
disabled, this circuit exists only to support unicast tunnels; in
this case, all other paramters are ignored.
|
| wfDvmrpCircuitMetric |
.1.3.6.1.4.1.18.3.5.3.12.2.1.6 |
|
Metric. This value represents the cost of this interface;
the cost of using this hop. This value must be smaller than the
route infinity value
|
| wfDvmrpCircuitRouteThreshold |
.1.3.6.1.4.1.18.3.5.3.12.2.1.7 |
|
Threshold. This value can be used to filter out datagrams
that are being forwarded to a neighboring router; if the IP TTL
is not >= the threshold, the datagram is dropped by this router
|
| wfDvmrpCircuitInPkts |
.1.3.6.1.4.1.18.3.5.3.12.2.1.8 |
|
Number of datagrams received on this interface
|
| wfDvmrpCircuitOutPkts |
.1.3.6.1.4.1.18.3.5.3.12.2.1.9 |
|
Number of datagrams send on this interface
|
| wfDvmrpCircuitInRouteUpdates |
.1.3.6.1.4.1.18.3.5.3.12.2.1.10 |
|
Number of DVMRP route update messages received
|
| wfDvmrpCircuitOutRouteUpdates |
.1.3.6.1.4.1.18.3.5.3.12.2.1.11 |
|
Number of DVMRP route update messages sent
|
| wfDvmrpCircuitInPktDiscards |
.1.3.6.1.4.1.18.3.5.3.12.2.1.12 |
|
Number of inbound datagrams discarded due to route not found
|
| wfDvmrpCircuitOutPktDiscards |
.1.3.6.1.4.1.18.3.5.3.12.2.1.13 |
|
Number of outbound datagrams discarded due to route not found
|
| wfDvmrpCircuitFwdCacheSize |
.1.3.6.1.4.1.18.3.5.3.12.2.1.14 |
|
Maximum number of entries allowed in the Forwarding table
at one time. there is a Forwarding table per vif
|
| wfDvmrpCircuitFwdCacheTTL |
.1.3.6.1.4.1.18.3.5.3.12.2.1.15 |
|
The time_to_live for the Forwarding table entries in seconds .
|
| wfDvmrpCircuitAdvertiseSelf |
.1.3.6.1.4.1.18.3.5.3.12.2.1.16 |
|
If enabled the router will advertise itself as one of
the source net. If not enabled the router will not advertise
itself as one of the source net.
|
| wfDvmrpCircuitFwdCacheEntries |
.1.3.6.1.4.1.18.3.5.3.12.2.1.17 |
|
The most up to date number of entries in the forwarding cache
|
| wfDvmrpCircuitInPrunePkts |
.1.3.6.1.4.1.18.3.5.3.12.2.1.18 |
|
Number of PRUNE datagrams received on this interface
|
| wfDvmrpCircuitOutPrunePkts |
.1.3.6.1.4.1.18.3.5.3.12.2.1.19 |
|
Number of PRUNE datagrams send on this interface
|
| wfDvmrpCircuitInGraftPkts |
.1.3.6.1.4.1.18.3.5.3.12.2.1.20 |
|
Number of GRAFT datagrams received on this interface
|
| wfDvmrpCircuitOutGraftPkts |
.1.3.6.1.4.1.18.3.5.3.12.2.1.21 |
|
Number of GRAFT datagrams send on this interface
|
| wfDvmrpCircuitInGraftAckPkts |
.1.3.6.1.4.1.18.3.5.3.12.2.1.22 |
|
Number of GRAFT_ACK datagrams received on this interface
|
| wfDvmrpCircuitOutGraftAckPkts |
.1.3.6.1.4.1.18.3.5.3.12.2.1.23 |
|
Number of GRAFT_ACK datagrams send on this interface
|
| wfDvmrpCircuitDefaultRouteSupply |
.1.3.6.1.4.1.18.3.5.3.12.2.1.24 |
|
enabled : Send the default route, 0.0.0.0 if learned,
form this interface.
disabled: no default route is sent from this interface.
generate: generate default route, 0.0.0.0 from this
interface.
|
| wfDvmrpCircuitDefaultRouteListen |
.1.3.6.1.4.1.18.3.5.3.12.2.1.25 |
|
Receive the default route, 0.0.0.0 on this interface
|
| wfDvmrpCircuitReportDependProbe |
.1.3.6.1.4.1.18.3.5.3.12.2.1.26 |
|
This is to control accepting the route report. According to
the protocol, dvmrp should send probe packet before sending
the route report packet to the neighbors. But some vendor
implementation did not send probes before sending reports.
Enable: only process the routes from the neighbor sending
probes. Disable: No Dependency (no restriction).
|
| wfDvmrpCircuitPruneLifeTime |
.1.3.6.1.4.1.18.3.5.3.12.2.1.27 |
|
The life time of the prune message the router sends
to its neighbor in seconds.
|
| wfDvmrpCircuitAcceptAggregateRoutes |
.1.3.6.1.4.1.18.3.5.3.12.2.1.28 |
|
Count of number of routes received have been
aggregated to the specific aggregate route currently
in route table for this interface.
|
| wfDvmrpCircuitAnnounceAggregatedRoutes |
.1.3.6.1.4.1.18.3.5.3.12.2.1.29 |
|
Count of number of routes have been aggregated to
the specific aggregate route for advertisement currently
in route table for this interface.
|
| wfDvmrpTunnelCCT |
.1.3.6.1.4.1.18.3.5.3.12.3.1.4 |
|
The multicast circuit associated with this tunnel.
|
| wfDvmrpTunnelLocalRouterIpAddress |
.1.3.6.1.4.1.18.3.5.3.12.3.1.15 |
|
(unicast) IP address of local network router. To support multinet.
|
| wfDvmrpTunnelRemoteRouterIpAddress |
.1.3.6.1.4.1.18.3.5.3.12.3.1.5 |
|
(unicast) IP address of remote network router neighbor.
|
| wfDvmrpTunnelCreate |
.1.3.6.1.4.1.18.3.5.3.12.3.1.1 |
|
create/delete
|
| wfDvmrpTunnelEnable |
.1.3.6.1.4.1.18.3.5.3.12.3.1.2 |
|
enable/disable this tunnel interface
|
| wfDvmrpTunnelState |
.1.3.6.1.4.1.18.3.5.3.12.3.1.3 |
|
The current state of the DVMRP tunnel interface. Invalid
indicates an error in processing the configuration record.
|
| wfDvmrpTunnelEncapsMode |
.1.3.6.1.4.1.18.3.5.3.12.3.1.6 |
|
Will these tunnelled datagrams be encapsulated within an IP datagram, or will
they be loosely encapsulated using the LSSR option (for the latter, refer to
RFC 1075; this is needed for backward compatibility)
|
| wfDvmrpTunnelMetric |
.1.3.6.1.4.1.18.3.5.3.12.3.1.7 |
|
Cost of using this tunnel
|
| wfDvmrpTunnelThreshold |
.1.3.6.1.4.1.18.3.5.3.12.3.1.8 |
|
Threshold for forwarding through this tunnel; if TTL < threshold, the
datagram is dropped.
|
| wfDvmrpTunnelInPkts |
.1.3.6.1.4.1.18.3.5.3.12.3.1.9 |
|
Number of datagrams received on this interface
|
| wfDvmrpTunnelOutPkts |
.1.3.6.1.4.1.18.3.5.3.12.3.1.10 |
|
Number of datagrams send on this interface
|
| wfDvmrpTunnelInRouteUpdates |
.1.3.6.1.4.1.18.3.5.3.12.3.1.11 |
|
Number of DVMRP route update messages received
|
| wfDvmrpTunnelOutRouteUpdates |
.1.3.6.1.4.1.18.3.5.3.12.3.1.12 |
|
Number of DVMRP route update messages sent
|
| wfDvmrpTunnelInPktDiscards |
.1.3.6.1.4.1.18.3.5.3.12.3.1.13 |
|
Number of inbound datagrams discarded due to route not found or due to
invalid inner address (dest address != multicast)
|
| wfDvmrpTunnelOutPktDiscards |
.1.3.6.1.4.1.18.3.5.3.12.3.1.14 |
|
Number of outbound datagrams discarded due to route not found
|
| wfDvmrpTunnelFwdCacheSize |
.1.3.6.1.4.1.18.3.5.3.12.3.1.16 |
|
Maximum number of entries allowed in the Forwarding table
at one time. there is a Forwarding table per vif
|
| wfDvmrpTunnelFwdCacheTTL |
.1.3.6.1.4.1.18.3.5.3.12.3.1.17 |
|
The time_to_live for the Forwarding table entries in seconds .
|
| wfDvmrpTunnelFwdCacheEntries |
.1.3.6.1.4.1.18.3.5.3.12.3.1.18 |
|
The most up to date number of entries in the forwarding cache
|
| wfDvmrpTunnelInPrunePkts |
.1.3.6.1.4.1.18.3.5.3.12.3.1.19 |
|
Number of PRUNE datagrams received on this interface
|
| wfDvmrpTunnelOutPrunePkts |
.1.3.6.1.4.1.18.3.5.3.12.3.1.20 |
|
Number of PRUNE datagrams send on this interface
|
| wfDvmrpTunnelInGraftPkts |
.1.3.6.1.4.1.18.3.5.3.12.3.1.21 |
|
Number of GRAFT datagrams received on this interface
|
| wfDvmrpTunnelOutGraftPkts |
.1.3.6.1.4.1.18.3.5.3.12.3.1.22 |
|
Number of GRAFT datagrams send on this interface
|
| wfDvmrpTunnelInGraftAckPkts |
.1.3.6.1.4.1.18.3.5.3.12.3.1.23 |
|
Number of GRAFT_ACK datagrams received on this interface
|
| wfDvmrpTunnelOutGraftAckPkts |
.1.3.6.1.4.1.18.3.5.3.12.3.1.24 |
|
Number of GRAFT_ACK datagrams send on this interface
|
| wfDvmrpTunnelDefaultRouteSupply |
.1.3.6.1.4.1.18.3.5.3.12.3.1.25 |
|
Send the default route, 0.0.0.0 on this interface
|
| wfDvmrpTunnelDefaultRouteListen |
.1.3.6.1.4.1.18.3.5.3.12.3.1.26 |
|
Receive the default route, 0.0.0.0 on this interface
|
| wfDvmrpTunnelCtrlMsgMode |
.1.3.6.1.4.1.18.3.5.3.12.3.1.27 |
|
Dvmrp tunneling control messages encapsulated type.
noencaps is the mode that control messages are sent in regular
igmp packets with ip protocol type set to IP_PROTOCOL_IGMP.
encaps is the mode that control messages are encapsed inside
ip packets with ip protocol type set to IP_PROTOCOL_IPINIP.
All DVMRP messages sent across tunnels will be encapsulated
in the same way as data packets in this mode.
|
| wfDvmrpTunnelReportDependProbe |
.1.3.6.1.4.1.18.3.5.3.12.3.1.28 |
|
This is to control accepting the route report. According to
the protocol, dvmrp should send probe packet before sending
the route report packet to the neighbors. But some vendor
implementations do not send probes before sending reports.
Enable: only process the routes from the neighbor sending
probes. Disable: No Dependency (no restriction).
|
| wfDvmrpTunnelPruneLifeTime |
.1.3.6.1.4.1.18.3.5.3.12.3.1.29 |
|
The life time of the prune message the router send
to its neighbor in seconds.
|
| wfDvmrpTunnelAcceptAggregateRoutes |
.1.3.6.1.4.1.18.3.5.3.12.3.1.30 |
|
Count of number of routes received have been
aggregated to the specific aggregate route currently
in route table for this interface.
|
| wfDvmrpTunnelAnnounceAggregatedRoutes |
.1.3.6.1.4.1.18.3.5.3.12.3.1.31 |
|
Count of number of routes have been aggregated to
the specific aggregate route for advertisement currently
in route table for this interface.
|
| wfDvmrpRouteSourceNetwork |
.1.3.6.1.4.1.18.3.5.3.12.4.1.1 |
|
A source of multicast datagrams
|
| wfDvmrpRouteSourceMask |
.1.3.6.1.4.1.18.3.5.3.12.4.1.2 |
|
Mask for the specified source network
|
| wfDvmrpRouteNextHopRouter |
.1.3.6.1.4.1.18.3.5.3.12.4.1.3 |
|
Next hop multicast router to the specified source
network; we consider this neighboring router to be on the
shortest path to the source. Note that this neighboring router
may be a tunnel endpoint.
|
| wfDvmrpRouteNextHopInterfaceCCT |
.1.3.6.1.4.1.18.3.5.3.12.4.1.4 |
|
Next hop interface (CCT) to the specified source router; we
consider this interface to be on the shortest path to the source.
|
| wfDvmrpRouteNextHopInterfaceTunnelId |
.1.3.6.1.4.1.18.3.5.3.12.4.1.5 |
|
Next hop interface (tunnel id) to the specified source router; we
consider this interface to be on the shortest path to the source.
|
| wfDvmrpRouteNextHopInterfaceLocalTunnelId |
.1.3.6.1.4.1.18.3.5.3.12.4.1.6 |
|
Next hop interface (local tunnel id) to the specified source router; we
consider this interface to be on the shortest path to the source.
|
| wfDvmrpRouteTimer |
.1.3.6.1.4.1.18.3.5.3.12.4.1.7 |
|
route timer
|
| wfDvmrpRouteState |
.1.3.6.1.4.1.18.3.5.3.12.4.1.8 |
|
Set of flags indicating state of entry. Note that the
router uses this field as a bit mask.
0x8000 Network is local to this router
0x4000 Route is being timed
0x2000 Route is garbaged
|
| wfDvmrpRouteMetric |
.1.3.6.1.4.1.18.3.5.3.12.4.1.9 |
|
current route metric
|
| wfDvmrpRouteProtocol |
.1.3.6.1.4.1.18.3.5.3.12.4.1.10 |
|
current route protocol dvmrp (2) or mospf (4) or internal (6)
which is the route from unicast and incoming interface no i
dvmrp configure, if dvmrp is configured then the protocol will
be set to 2, see wfIgmpRoutingProtocol
|
| wfDvmrpRouteType |
.1.3.6.1.4.1.18.3.5.3.12.4.1.11 |
|
The orginal route source from. If it is from
pure dvmrp route (0x0001)
unicast best route (0x0002)
unciast route but has dvmrp interface (0x0003)
ospf(0x0004)
ospf best route (0x0006)
ospf ase route (0x0008)
|
| wfDvmrpRouteAggregatedType |
.1.3.6.1.4.1.18.3.5.3.12.4.1.12 |
|
Route Aggregated types :
0 - normal route
1 - inbound aggregated route
2 - outbound aggregated route
4 - inbound aggregate route
8 - outbound aggregate route
|
| wfDvmrpRouteInterfaceSourceNetwork |
.1.3.6.1.4.1.18.3.5.3.12.5.1.1 |
|
A source of multicast datagrams
|
| wfDvmrpRouteInterfaceParentCCT |
.1.3.6.1.4.1.18.3.5.3.12.5.1.15 |
|
circuit number with which this route is associated;parent VIF
|
| wfDvmrpRouteInterfaceParentLocalTunnelId |
.1.3.6.1.4.1.18.3.5.3.12.5.1.16 |
|
Tunnel ID for tunnelled interfaces. This value is zero
for non-tunnelled interfaces, otherwise it contains the local IP
address of the tunnel; parent VIF.
|
| wfDvmrpRouteInterfaceParentTunnelId |
.1.3.6.1.4.1.18.3.5.3.12.5.1.17 |
|
Tunnel ID for tunnelled interfaces. This value is zero
for non-tunnelled interfaces, otherwise it contains the remote IP
address of the tunnel; parent VIF.
|
| wfDvmrpRouteInterfaceSourceMask |
.1.3.6.1.4.1.18.3.5.3.12.5.1.2 |
|
Mask for the specified source network
|
| wfDvmrpRouteInterfaceNextHopInterfaceCCT |
.1.3.6.1.4.1.18.3.5.3.12.5.1.3 |
|
circuit number with which this route is associated
|
| wfDvmrpRouteInterfaceNextHopInterfaceLocalTunnelId |
.1.3.6.1.4.1.18.3.5.3.12.5.1.4 |
|
Tunnel ID for tunnelled interfaces. This value is zero
for non-tunnelled interfaces, otherwise it contains the local IP
address of the tunnel.
|
| wfDvmrpRouteInterfaceNextHopInterfaceTunnelId |
.1.3.6.1.4.1.18.3.5.3.12.5.1.5 |
|
Tunnel ID for tunnelled interfaces. This value is zero
for non-tunnelled interfaces, otherwise it contains the remote IP
address of the tunnel.
|
| wfDvmrpRouteInterfaceState |
.1.3.6.1.4.1.18.3.5.3.12.5.1.6 |
|
state of interface for this route. Note that the router
uses this field as a bit mask.
0x8000 - interface is leaf
0x4000 - interface is child
0x2000 - interface is in hold-down state
0x1000 - interface has loop neighbor for this route
|
| wfDvmrpRouteInterfaceDominantRouter |
.1.3.6.1.4.1.18.3.5.3.12.5.1.7 |
|
dominant router address for virtual interface
|
| wfDvmrpRouteInterfaceSubordinateRouter |
.1.3.6.1.4.1.18.3.5.3.12.5.1.8 |
|
subordinate router address for virtual interface
|
| wfDvmrpRouteInterfaceHoldDownTimer |
.1.3.6.1.4.1.18.3.5.3.12.5.1.9 |
|
Current value of hold down timer, used to determine if
interface is for leaf or non-leaf network. Non-leaf network means
that a local network router considers us to be in the shortest
path to the source (they have sent us a route update with metric
>= infinity).
|
| wfDvmrpRouteInterfaceSPInDiscards |
.1.3.6.1.4.1.18.3.5.3.12.5.1.10 |
|
Count of inbound packets discarded because interface not on shortest path
|
| wfDvmrpRouteInterfaceSPOutDiscards |
.1.3.6.1.4.1.18.3.5.3.12.5.1.11 |
|
Count of outbound packets discarded because interface not on shortest path
|
| wfDvmrpRouteInterfaceThresholdOutDiscards |
.1.3.6.1.4.1.18.3.5.3.12.5.1.12 |
|
Count of outbound packets discarded because of threshold
|
| wfDvmrpRouteInterfaceInSuccessfulPkts |
.1.3.6.1.4.1.18.3.5.3.12.5.1.13 |
|
Count of inbound packets accepted for forwarding
|
| wfDvmrpRouteInterfaceOutSuccessfulPkts |
.1.3.6.1.4.1.18.3.5.3.12.5.1.14 |
|
Count of outbound packets accepted for forwarding
|
| wfDvmrpNeighboringRouterCCT |
.1.3.6.1.4.1.18.3.5.3.12.6.1.1 |
|
Local circuit number
|
| wfDvmrpNeighboringRouterLocalTunnelId |
.1.3.6.1.4.1.18.3.5.3.12.6.1.2 |
|
Tunnel Id for interface. This value is zero for non-
tunnelled interfaces, otherwise it contains the IP address of the
local tunnel endpoint.
|
| wfDvmrpNeighboringRouterTunnelId |
.1.3.6.1.4.1.18.3.5.3.12.6.1.3 |
|
Tunnel Id for interface. This value is zero for non-
tunnelled interfaces, otherwise it contains the IP address of the
remote tunnel endpoint.
|
| wfDvmrpNeighboringRouterIpAddr |
.1.3.6.1.4.1.18.3.5.3.12.6.1.4 |
|
IP address of neighboring router
|
| wfDvmrpNeighboringRouterState |
.1.3.6.1.4.1.18.3.5.3.12.6.1.5 |
|
State of neighbor. The router uses this as a bit mask.
0x8000 - Neighbor is being timed
|
| wfDvmrpNeighboringRouterTimer |
.1.3.6.1.4.1.18.3.5.3.12.6.1.6 |
|
Current value of neighbor timer
|
| wfDvmrpNeighboringRouterGenId |
.1.3.6.1.4.1.18.3.5.3.12.6.1.7 |
|
The neighboring router's generation identifier.
|
| wfDvmrpNeighboringRouterMajorVersion |
.1.3.6.1.4.1.18.3.5.3.12.6.1.8 |
|
The neighboring router's major DVMRP version number.
|
| wfDvmrpNeighboringRouterMinorVersion |
.1.3.6.1.4.1.18.3.5.3.12.6.1.9 |
|
The neighboring router's minor DVMRP version number.
|
| wfDvmrpNeighboringRouterCapabilities |
.1.3.6.1.4.1.18.3.5.3.12.6.1.10 |
|
This object describes the neighboring router's capabilities.
The leaf bit indicates that the neighbor has only one
interface with neighbors. The prune bit indicates that the
neighbor supports pruning. The generationID bit indicates
that the neighbor sends its generationID in Probe messages.
The mtrace bit indicates that the neighbor can handle
mtrace requests.
|
